Russell Hobbs Coffeemaker 10444 User Guide

10444_IB_3-5-02 5/3/02 3:19 PM Page 1  
ESPRESSO MAKER  
Model No. 10444  
Instructions and guarantee  
 
10444_IB_3-5-02 5/3/02 3:19 PM Page 3  
Read these instructions before using your Espresso Maker and keep them in a  
safe place for future reference. If you pass the Espresso Maker on to anyone  
else, pass on the instructions too. Remove all packaging, but keep it until  
you’re satisfied that the Espresso Maker is working.  
Important safeguards  
When using electrical appliances, follow basic safety precautions, including:  
1.Take care — the espresso maker uses steam under pressure.  
2.Don’t try to remove the pressure cap while the espresso maker is  
working.  
3.Release all pressure after use and before trying to remove the  
pressure cap.  
4.The espresso maker must always be supervised while switched on.  
5.The espresso maker must be used only by a responsible adult.  
6.Don’t put it in water, don’t use it in a bathroom or near any  
source of water, and don’t use it outdoors.  
7.Don’t touch hot surfaces (carafe, filter holder or steam pipe),  
use handles/knobs.  
8.Take care to avoid contact with steam when using the milk frother.  
9.Fill with at least 2 cups of water, but not more than one carafe-full.  
10.Don’t overfill. If overfilled, boiling water or steam may be ejected.  
11.Use only clean, cold, fresh water, don’t fill with milk or any other liquid.  
12.Before refilling the espresso maker, switch it off, let it cool down for a  
couple of minutes, then release the pressure before removing the pressure  
cap (“Releasing steam” on page 6).  
13.Don’t interfere with the espresso maker while it’s brewing. If you need to  
stop it for any reason, turn off the heating, unplug it, let it cool down,  
then release the pressure (“Releasing steam” on page 6).  
16.Position the espresso on a firm, level, heat-resistant surface, close to a  
power socket and out of reach of children.  
17.Route the mains lead so that it doesn’t overhang and can’t be caught  
accidentally.  
18.Keep the espresso maker and the mains lead away from hot surfaces,  
hotplates, hot hobs and burners.  
20.Unplug the espresso maker when not in use, before moving and before  
cleaning. Let it cool down and release the pressure (“Releasing steam” on  
page 6) before moving or cleaning.  
21.Don’t use accessories or attachments other than those we provide.  
22.Don’t use the espresso maker for any purpose other than those described in  
these instructions.  
23.Don’t operate this appliance after it malfunctions or if the power cord or  
plug is damaged. There are no user-serviceable parts. If the mains lead is  
damaged, the coffee maker must be returned in order to avoid hazard.  
24.Don’t try to reposition the handle on the carafe, you’ll break the glass.  
Household use only  
3
 
10444_IB_3-5-02 5/3/02 3:19 PM Page 4  
Safety valve  
In the unlikely event of the normal controls failing, a safety valve in the  
pressure cap will open automatically and release excess pressure. If this  
happens, don’t touch the espresso maker. Unplug it and let it cool down for at  
least one hour before trying to release the pressure or open the pressure cap.  
Before use  
Before using the espresso maker for the first time, or if it hasn’t been used for  
a long time, clean out any dust that may have gathered inside it.  
Run it through three cycles without coffee. Between cycles, discard the water,  
unplug, let it cool, and release the pressure (“Releasing steam” on page 6).  
Using the Espresso Maker  
Note: Measurements are given in metric units. Imperial units given in brackets  
are only rough equivalents.  
Making Espresso (from cold)  
1.Remove the carafe from under the filter holder. You’ll need to turn it until  
the slot in the carafe lid is aligned with the nozzle under the filter holder.  
2.Remove the pressure cap by turning it anticlockwise.  
Filling  
3.Pour the required amount of water into the pressure tank. You must use at  
least 125ml (4 fl oz), but not more than 400ml (14 fl oz).  
4.It’s best to use the carafe to measure the water. The front is marked from  
2 to 4 (espresso) cups. Fill to at least the 2 cup level. If you use the carafe,  
you can’t overfill the espresso maker.  
5.Refit the pressure cap and turn it clockwise until it’s fully tightened.  
6.Remove the filter holder by turning the handle to the left arrow (open) on  
the front of the espresso maker, then lower it from the brewing head.  
7.Check that the filter is inside the filter holder.  
8.Put enough fine ground coffee for 2 or 4 cups of espresso into the filter.  
Levels are marked on the inside of the filter. Don’t fill above the 4 mark.  
9.Tamp the coffee down lightly with a spoon — don’t press too hard, you’ll  
make the coffee too strong and bitter.  
10. Run the scoop round the filter holder rim to clear it of any coffee grounds.  
Loading  
11.Flip the retaining clip back, out of the way, then lift the filter holder up to  
the brewing head.  
12.Align the filter holder handle with the left arrow (open) on the  
front of the espresso maker. The lugs on top of the filter holder should  
engage in the lugs round the brewing head.  
13.Turn the handle to the right arrow (close) to lock the filter holder in place.  
The marks may not match exactly — turn the handle as far right as it’ll go.  
14.Put the lid on the carafe, turn it to align the arrow on the lid with the  
arrow on the side of the carafe, then slide the carafe between the filter  
holder and the drip tray.  
4
 
10444_IB_3-5-02 5/3/02 3:19 PM Page 5  
The control  
The control switches the element on and off and operates the valve. The  
“Heating” light indicates when the element is on.  
The positions are, anti-clockwise from the bottom:  
Hot water for coffee: the valve directs the output from the boiler to the  
brewing head to make coffee, the heater is switched on.  
Off closed: the valve is closed, the heater is switched off.  
Release steam: the valve is gradually opened to release residual steam, the  
heater is switched off.  
Steam for cappuccino: the valve directs the output from the boiler to the  
steam pipe to generate steam, the heater is switched on.  
Switching on  
15.Turn the control to bring the mark to the “Off closed” area.  
16.Plug the espresso maker into the power socket and switch the socket on if  
it’s switchable.  
17.Turn the control fully clockwise ` to heat the water. The “Heating” light  
will come on.  
18. Within a few minutes you’ll see coffee liquor dripping into the carafe. If  
you’re making Cappuccino, go to point 31 on page 6.  
19.When the coffee stops flowing, the process is complete.  
20.Turn the control clockwise to bring the mark to the “Off closed” area.  
Don’t turn it as far as the “Release steam” markings yet.  
5
 
10444_IB_3-5-02 5/3/02 3:19 PM Page 6  
Releasing steam  
Before you can remove the pressure cap safely, you have to release the steam  
remaining in the pressure tank.  
Warning: To avoid the risk of scalding, keep fingers, hands, etc. clear of the  
escaping steam.  
21.Unplug the espresso maker from the power socket (switch the socket off  
first if it’s switchable).  
22.Hold an empty mug or jug up to the milk frother, with the bottom of the  
milk frother well below the rim of the cup.  
23.Very slowly, turn the control anti-clockwise to the “Release steam”  
markings. The residual steam will escape from the end of the milk frother.  
24.The further round the “Release steam” markings you turn the control, the  
faster the steam will escape.  
25.Don’t turn it too far or too fast, and don’t turn it past the end of the  
“Release steam” markings.  
26.When all the steam has escaped, unscrew the pressure cap (anti-clockwise)  
and lift it off.  
27.Unless you’re going to re-use the espresso maker right away, let it cool  
then clean it.  
Drinking espresso  
28.If you’re drinking it neat, try slurping rather than drinking. It’s a bit noisy  
and not the thing to do in public, but slurping mixes air with the coffee, so  
the flavour fills your mouth, sinuses and nose as well as hitting your taste  
buds — noisy but nice!  
29.You’ll no doubt have heard that espresso coffee is supposed to be taken  
without milk. Who makes these rules? If we must have rules, then how  
about: if you take it with milk, use warm or hot milk to stop it going cold.  
30.If you take cream with it, pour the cream gently over the back of a warm  
spoon, so that it floats on top of the coffee rather than mixing in with it.  
No doubt this is bad for you, but it tastes nice.  
31.Cappuccino is made by spooning hot, frothy milk on top of cups of espresso,  
often sprinkled with powdered cinnamon, nutmeg or chocolate, sometimes  
garnished with a cinnamon stick.  
Making Cappuccino  
You’ll need a heat-resistant half litre jug (a 1pt or pt jug will do nicely)  
containing up to 270ml (pt) cold, semi-skimmed milk. To allow room for the  
froth, don’t fill the jug more than two thirds full.  
Ideally, the jug should be tall(ish) and narrow(ish), as the milk must be deep  
enough to cover the open end of the milk frother without the milk frother  
hitting the bottom of the jug.  
We’ve found that cold skimmed or semi-skimmed milk give better results than  
full cream milk. You’ll need to experiment with the milk supplied in your area  
to find which type works best for you.  
6
 
10444_IB_3-5-02 5/3/02 3:19 PM Page 7  
Follow points 1 to 18, then jump to point 31. At point 3, add extra water (half  
a cup to a cup), to generate the steam to heat and froth the milk.  
Use the carafe to measure the water. For 2 cups of coffee, fill the carafe to  
between the 2 and 3 cup marks, for 4 cups, fill to just below the spout.  
Don’t try to make too much froth at one time. Too much steam will flatten the  
milk, rather than froth it, leaving you with nothing but hot, watery milk. The  
technical name for this is “yeuch!”.  
Frothing the milk  
31.Watch the marks on the carafe. When the level reaches the number of cups  
you want, turn the control anti-clockwise till the “Heating” light goes out.  
32.Bring the jug containing the milk up to the milk frother and hold it so that  
the end of the milk frother is just under the surface of the milk.  
33.Turn the control anti-clockwise to ¬. This forces steam down the steam  
pipe to the milk frother. You’ll hear/see it burbling through the milk.  
34.Move the jug up and down slightly, keeping the end of the milk frother just  
below the surface of the milk.  
35.Don’t lift the end of the milk frother out of the milk, or the milk will  
spatter and steam will be ejected sideways.  
36.When you’ve got enough froth, turn the control clockwise past the “Release  
steam” markings to the blank area.  
37.Return to point 21 to release the residual steam.  
Making hot milk  
If you want to make warm milk to mix with your coffee, follow the procedure  
for making froth, but immerse the milk frother fully in the milk, so that the  
escaping steam bubbles through the milk, heating it all. Don’t use too much  
steam, or you’ll get watery milk.  
Stiffer froth  
Some people like to make the froth earlier in the process and let it stand, to  
stiffen it. You can go from coffee making ` to froth making ¬ as soon as  
the coffee reaches the a mark on the carafe. When you’ve made your froth,  
turn back to ` and finish making your coffee.  
Care and maintenance  
Before you do anything else, unplug the espresso maker, release the residual  
steam, then leave it to cool down.  
Flip the retaining clip forward and put a finger on it, to hold the metal filter in  
place while you empty it. This should stop you throwing the filter in the bin  
along with the coffee grounds. Alternatively, ring our Customer Service Dept,  
who’ll be happy to sell you a new filter.  
The pressure cap, filter holder, filter, carafe, lid, milk frother, drip tray and  
cover, should be hand washed in warm soapy water. Rinse and dry thoroughly.  
Rinse well to remove all traces of soap, then dry thoroughly before re-use or  
storing away.  
Wipe the body of the espresso maker with a soft, damp cloth.  
7
 
10444_IB_3-5-02 5/3/02 3:19 PM Page 8  
Removing the drip tray, cover, and frother  
To lift the drip tray cover, insert a fingertip in the indent on its right and lift it  
out. You can then lift the drip tray out (try not to spill the drips).  
To remove the milk frother, support the steam pipe with one hand and pull the  
milk frother gently down with the other hand. To refit, push the milk frother  
up the steam pipe until you feel resistance, then 15mm more (a bit over half  
an inch). The steam pipe shouldn’t stick through the frother.  
Releasing the residual steam after use normally keeps the steam tube from  
becoming blocked by milk residue. If residue builds up, clear the nozzle of the  
steam tube with a needle.  
Emptying the tank  
If you need to empty the pressure tank manually, unplug, let it cool, and  
release the pressure (“Releasing steam” on page 6). Remove all removable  
parts (carafe, filter holder, filter, pressure cap, drip tray, cover). Turn the  
espresso maker upside down over a sink or basin. Dry thoroughly before use.  
Don’t immerse the espresso maker in water or any other liquid.  
Don’t use harsh or abrasive cleaners or solvents.  
Descaling  
Scale build-up will overheat the element, reducing its working life. It may  
cause the safety cut-out to operate prematurely, switching off before the  
water boils. It’ll also lengthen the brewing time.  
To minimise scale build-up, empty after each use, don’t leave water in the  
pressure tank overnight, and descale regularly. Use a proprietary brand of  
descaler suitable for use in plastic-bodied products, and follow the instructions  
on the packet of descaler. After descaling, run it twice with fresh water  
(without coffee), including the frother stage (without milk). Discard the water.  
Frequency of descaling depends on water hardness. In areas of very hard water  
you may have to use filtered water instead of ordinary tap water.  
If the descaler doesn’t have instructions for espresso makers, use the  
proportions (descaler to water) for a kettle, then run the espresso maker twice  
with this mixture (without coffee), including the frother stage (without milk).  
Note: Products returned during the guarantee period with faults which are  
directly related to scale build-up will be subject to a repair charge.  
8
 
10444_IB_3-5-02 5/3/02 3:19 PM Page 9  
Connection to the mains supply  
Check that the voltage marked on the appliance  
corresponds with the supply voltage.  
The appliance must be earthed. It’s supplied with  
three-core mains lead and a 13A plug complying with  
BS1363. To replace the fuse, use a 13A ASTA or BSI  
approved fuse conforming to BS1362.  
The appliance conforms to EC Directive 92/31/EEC with  
respect to Electromagnetic Compatibility  
If the plug needs replacing  
Connect the Green/Yellow wire (Earth) to the terminal  
marked E or  
. Connect the Blue wire (Neutral) to the terminal marked N.  
Connect the Brown wire (Live) to the terminal marked L. Secure the cord grip.  
If in doubt consult an electrician.  
If the plug supplied is non-rewireable (moulded)  
Don’t use the plug without the fuse cover in place. If you need to  
remove the plug, cut it off and dispose of it. To avoid electric shock,  
don’t re-use the plug or put it into a socket.  
After sales service  
The appliance isn’t user–serviceable. If it’s not working properly, check:  
1.You’ve followed the instructions correctly.  
2.The plug fuse hasn’t blown.  
3.The main supply fuse/circuit breaker hasn’t blown/tripped.  
If it still doesn’t work, consult your retailer. If your retailer fails to solve your  
problem, and you need to return it to us, proceed as follows:  
1.Pack it carefully.  
2.Enclose your name, address, and daytime telephone number.  
3.Tell us what’s wrong with it.  
4.If under guarantee, state where and when bought, and include proof of  
purchase (e.g. till receipt).  
5.Send it to Customer Service Dept, at the address at the end of this leaflet.  
6.They’ll give you an estimate for inspection/repair.  
9
 
10444_IB_3-5-02 5/3/02 3:19 PM Page 10  
Spare parts  
Phone Customer Service Dept on 0161-947-3111. Tell them the Model No. (on  
the product’s rating label), and the part(s) you need. They’ll give you the  
price(s).  
You may then:  
Either order spares by phone using MASTERCARD or VISA.  
Or  
fill in this form (or a copy), and send it, with a cheque or postal order  
payable to Salton Europe Ltd, to Customer Service Dept.  
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  
Your Name: ..................................................................................  
Your Address: ................................................................................  
..................................................................................................  
Post Code: ...............................  
Model No.  
Part(s) required  
Quantity  
I enclose a cheque/postal order for £ .......... in full payment.  
Guarantee  
Any defect affecting the functionality of the appliance which becomes  
apparent within three years of its purchase will be corrected by free repair or  
replacement provided that it has been used and maintained in accordance with  
the instructions and has not been abused or misused in any way. Your statutory  
rights are not affected.  
In line with our policy of continuous product development we reserve the right  
to change the product, packaging and documentation specifications without  
notice.  
Customer Service Department  
Salton Europe Ltd, Failsworth, Manchester M35 0HS England  
Telephone 0161–947–3111 Fax 0161–684–8712  
Leaflet No: 436-175  
10  
 

Radio Shack Telephone System 350 User Guide
Rangemaster Stove Toledo FS Hob User Guide
RCA Camcorder CC437 User Guide
Renesas Computer Hardware H8S 2214 Series User Guide
Samsung Cell Phone 07212010 User Guide
Samsung Cell Phone A640 User Guide
Samsung Cordless Telephone SGH t609 User Guide
Samsung Range FER300SB User Guide
Scientific Atlanta Universal Remote AT8400TM User Guide
Sears Treadmill 831297140 User Guide