Numark Industries PROFESSIONAL DUAL CDN 32S User Manual

®
Professional Disc Jockey Products  
CDN-32S  
PROFESSIONAL DUAL CD PLAYER  
with  
Buffered memory  
OPERATING MANUAL  
©1999  
Industries  
CDN-32S  
WARNING: To reduce the risk of fire or electrical  
shock, do not expose this appliance to rain or  
moisture. Electrical equipment should NEVER be  
kept or stored in damp environments.  
NOTICE CONCERNING FCC REGULATIONS  
This equipment generates and uses radio frequency  
energy and may cause interference to radio and  
television reception if you do not operate it in strict  
accordance with the procedures detailed in this  
OPERATING MANUAL.  
This unit complies with Class B computing device rules  
in accordance with the specifications in Sub-part J or  
Part 15 of the FCC Rules, which are designed to provide  
reasonable protection against such interference in a  
residential installation. There is no guarantee, however,  
that interference will not occur in a particular installation.  
If the unit does cause interference to any radio or  
television reception, try to reduce it by one or more of  
the following means:  
DANGER: INVISIBLE LASER RADIATION WHEN  
OPEN AND INTERLOCK FAILED OR DEFEATED.  
AVOID DIRECT EXPOSURE TO BEAM.  
CAUTION: This product utilizes a laser. Use of  
controls or adjustments other than those  
specified herein may result in hazardous  
radiation exposure.  
SERVICE INSTRUCTIONS  
a) Reposition the other unit and/or its antennae  
b) Move this unit  
c) Move this unit and the other unit(s) further apart  
d) Plug this unit into a different AC outlet so that it is  
on a different circuit from the other equipment.  
·
·
Disconnect power cord before servicing  
Replace critical components  
with factory parts or recommended  
equivalents  
only  
This note is in accordance with Section 15.838 of the  
FCC Rules.  
·
For AC line powered units - Before returning  
repaired unit to user, use an ohmmeter to  
measure from both AC plug blades to all  
exposed metallic parts. The resistance should  
be no more than 100,000ohms.  
This unit does not exceed the Class B limits for  
radio noise emission from digital apparatus set out  
in the radio interference regulations of the  
Canadian Department of Communications.  
DOUBLE INSULATED - When servicing use only identical replacement parts  
For 220-volt use in USA, use NEMA style 220-volt plug. For other countries use proper plug for local outlet.  
LINE VOLTAGE SELECTION  
1 1 5 V  
1) The desired voltage may be set with the VOLTAGE SELECTOR switch on the  
rear panel of the main unit, using a screwdriver.  
2) Do not twist the VOLTAGE SELECTOR switch with excessive force as this may  
cause damage.  
2 3 0 V  
3) If the VOLTAGE SELECTOR switch does not move smoothly contact a qualified serviceman.  
Please record the serial number of your unit as shown on the back of the chassis as well as the  
name of the dealer from whom you purchased the unit. Retain this information and your original  
purchase receipt for your records. Please return the enclosed warranty card to register your CD  
player with us.  
MODEL: ___________________________ PURCHASED FROM: ________________________  
SERIAL NUMBER: __________________  
DATE OF PURCHASE: _______________________  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 3 -  
CDN-32S  
®
CDN-32S  
PROFESSIONAL DUAL CD PLAYER  
WITH  
CONGRATULATIONS...  
You have just purchased a dual CD player designed specifically for the  
professional DJ. This unit has been designed to provide CD mixing with the same  
ease and creativity that you have enjoyed with records. Please take a few moments to  
familiarize yourself with the CDN-32 by reading the following information before  
attempting to operate the unit.  
Once again, congratulations and thank you for making the CDN-32 your choice in  
professional CD players.  
FEATURES:  
· Anti-Shock buffered memory  
· True buffered instant start  
· Interactive pitch wheel adjustment  
· Fader/relay start  
· Digital Output  
· 3 speed scanning  
· Frame search  
· Auto cue  
· +10 tracks skip search  
· 30 tracks program play  
· Pitch display  
· 8 times oversampling  
· 8cm single CD compatible  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 4 -  
CDN-32S  
TABLE OF CONTENTS  
Safety and Registration  
2
4
7
Introduction  
Set-up Instructions & Connections  
Description of the Features  
Remote Control Unit  
Display  
8
9
9
Transport  
Basic Operation  
Play, Pause and Cue Operations  
Matching the Tempo  
Beat Matching Using Pitch Bend  
Relay and Fader Start  
10  
11  
11  
12  
Example of Mixing  
13  
14  
14  
15  
16  
Before Switching off the Power  
Troubleshooting Guide  
Information and Specifications  
Warranty  
CHECK TO BE SURE  
THE FOLLOWING ITEMS ARE IN THIS BOX:  
1) DUAL-TRANSPORT PLAYER UNIT  
1) REMOTE CONTROL UNIT  
1) OWNERS MANUAL (THIS BOOKLET)  
2) RCA CONNECTING CABLES  
2) CONTROL CABLES  
1) FADER START CABLE  
1) IEC POWER CORD  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 5 -  
CDN-32S  
DESCRIPTION OF ANTI-SHOCK BUFFER MEMORY  
The CDN-32S is equipped with a total of 24 Seconds of RAM Buffer memory.  
12 Seconds of this is used for the Anti-Shock Buffer and the other 12 are used for  
instant start functions. Anti-shock is to allows the unit to be bumped around hard for 6  
seconds per side and not stop. When the CD is first placed in the tray and a track is  
selected, the CD player quickly reads the beginning of the track and stores it into a  
buffer memory, the same way a computer stores information in RAM. This initial  
operation takes about 5 seconds. As you play the track, the CD Player continues to  
read ahead of the music and stores this information in the buffer. If the unit is  
bumped the CD Player will continue to play from this buffer until the unit recovers and  
can start filling the buffer again. The buffer should be long enough to allow recovery  
from most situations, however, continual shocks can erase the buffer memory. If the  
unit should ever run out of buffer and still be receiving shocks, then the last 2 seconds  
will repeat until continuation can occur. The music never stops.  
NOTE: The CD player can not store buffer information during the setting of a cue  
point with the jog wheel. If you start a CD without giving it an opportunity to load the  
buffer it will still start instantly and load buffer slowly. It will recover 1 second of buffer  
for every 6 seconds of music played at 0% pitch.  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 6 -  
CDN-32S  
CONNECTIONS  
Typical connection with a mixer is illustrated right.  
1. Connect the output connection cords from the CD Player to the line  
inputs of your mixer.  
2. Connect the remote control connection cable from the Unit 1 connector  
on the main unit to the Unit 1 connector on the remote control unit.  
Repeat for Unit 2.  
3. The output connection cords and the remote control connection cables  
are supplied with the main unit. Be sure to use the remote control  
connection cables which have been supplied. Use of another cable type  
might cause damage.  
4. Connect Relay or Fader start cables  
·
For fader start attach both side of your CD play to a similarly equipped  
DJ mixer, as in the top drawing.  
·
For relay capability take the autostart cable and connect the two jacks in  
the rear of your CD player.  
POWER ATTACHMENT: Your CD player is  
equipped with an IEC style power connector.  
Please first select the proper voltage for your  
location. Next, plug in you supplied power  
cable into the rear of the unit then plug into  
the appropriate power outlet.  
DIGITAL OUTPUTS: This CD player is specially equipped with digital outputs. The format is  
type 2, form 1, also known as S/PDIF (Sony/Phillips Digital Interface Format). In order to use  
the digital output you must activate the rear panel switch. When the digital output is active  
the variable pitch slider and pitch bend buttons or pitch wheel will not work.  
Note: If digital information was allowed to change in pitch, other devices will not read the digital output properly.  
MOUNTING YOUR CD PLAYER  
·
·
·
Mount the units in your console or rack with 19” EIA rails  
The transport should be mounted not to exceed an angle of 15 degrees.  
Your CD player can be affected by excess vibration so mount the units  
in a secure environment if possible.  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 7 -  
CDN-32S  
DESCRIPTION CDN-32S REMOTE FEATURES  
button is pressed (allowing “fall back”) and return to the  
1. PROGRAM - Depress this button and the unit will  
stop and the program indicator will light. Select  
each track to be programmed and press the  
PROGRAM button between selections. You can  
program up to 30 tracks. Press PLAY to start the  
program. To exit and erase program hold the  
program button down for more than 2 seconds while  
the unit is stopped, open the disc tray, or turn off the  
power.  
original pitch when the button is released. By changing  
the pitch of one disc with respect to the other in this  
way the beats can be matched.  
10. SEARCH WHEEL (OUTER RING) - This wheel has 3  
forward and 3 reverse speed positions for searching  
through songs. The more you turn the wheel in either  
direction the faster you search through the music.  
11. JOG WHEEL (INNER RING) - This jog wheel serves 2  
2. CONT/SING - Will cause just a single track to play or  
functions depending on the current mode.  
all tracks in order by pressing once or twice.  
a) The jog wheel will act as a slow frame search  
control when the CD is not playing but either  
paused or set to a cue point. To set a new frame  
cue point, spin the wheel then press play when you  
have determined the proper position. Press CUE to  
return to the “CUE POINT”.  
3. LCD DISPLAY - Indicates all the functions, as they  
are occurring, with the CD. These functions are  
explained in the next section.  
4. TIME (Time Button) - The TIME button switches the  
time display between elapsed playing time and  
remaining time on the track. Holding for more than  
one second activates auto-start functions.  
b) The jog wheel will temporarily bend the pitch of the  
music if the song is already playing by rotating the  
wheel clockwise to speed up or counterclockwise to  
slow down.  
5. OPEN/CLOSE (Disc Tray Open/Close) - Press to  
load or eject the disc. Each press will open or close  
the disc tray on the transport. NOTE: Tray will not  
open unless the disc has been paused.  
12. CUE - Pressing the CUE button during play provides a  
return to the position at which play was started. If  
PAUSE is used before CUE, that will become the cue  
point. Alternately pressing the PLAY button and the  
CUE button allows the CD to be played from the same  
position any number of times. The CUE LED will light  
up from the time the CUE button is pressed until the CD  
has reset to the position at which play was started.  
Steady lighting of this LED indicates the ready  
condition.  
6. TRACK (Track Buttons) - These buttons are used  
to select the track to be played.  
7. Track 10 Button - This button is for quickly  
advancing to higher tracks on a CD.  
8. PITCH (Pitch Button) - This button activates the  
Pitch Slider (14).  
9. PITCH BEND (Pitch Bend Button) - When each of  
the two CD players is playing a CD, the pitch bend  
function allows the positioning of the bass beats to  
be matched after the pitch of each disc is matched.  
Either player can “catch up” or “fall back” to match  
the other player. The pitch will automatically rise  
while the + button is pressed (allowing “catch up”)  
and return to the original pitch when the button is  
released. The pitch will automatically drop while the  
13. START/PAUSE (Play/Pause Button) - Each press of  
the Play/Pause Button causes the operation to change  
from play to pause or from pause to play.  
14. PITCH SLIDER - The pitch can be changed up to +/-  
12% by pressing the PITCH button so the PITCH LED  
is lit, then moving the sliding fader. The pitch will not be  
changed if the PITCH LED is off.  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 8 -  
CDN-32S  
LCD DISPLAY FEATURES  
TRANSPORT FEATURES  
19. DISC TRAY- Place your CD in here.  
20. OPEN/CLOSE (Disc Tray Open/Close) - Press to  
load or eject the disc. Each press will open or close  
the disc tray on the transport. NOTE: Tray will not  
open unless the disc has been paused.  
c) PLAY - Active while the unit is actually playing a CD.  
21. POWER BUTTON - Turn on and turn off the  
machine from this button. The unit should always be  
shut down with this button first before any external  
power is removed.  
d) PAUSE - Active when the unit is paused.  
e) CUE - Flashing when the unit is setting a cue point.  
Lit continuously when the unit is paused at a cue  
point.  
22. RCA AUDIO JACKS - Connect your CD player to  
f) PROGRAM - Used for preprogramming the track  
order to automatically be played by the unit. This is  
a great function if you need to leave the CD player  
alone.  
your mixer from this line level output.  
23. VOLTAGE SELECTOR - Set this switch to the  
voltage for your location.  
24. IEC POWER CONNECTOR - Plug your supplied  
power cord into here then plug unit into a power  
outlet.  
g) TIME MODE -  
(Elapsed) is for showing time as it is taking place.  
(Remain) shows how much time is left on a  
particular track. This function is controlled by the  
TIME BUTTON (4).  
25. CONTROL CONNECTOR - Plug your control cables  
for each unit into here and the back of the remote  
unit.  
h) SINGLE - Shows when the unit is set to play just  
one track at a time. When this is not lit the CD will  
play continuously through all tracks. This function is  
controlled by the SING/CONT BUTTON (2).  
26. DIGITAL OUTPUTS - The format is type 2, form 1,  
also known as S/PDIF (Sony/Phillips Digital Interface  
Format). In order to use the digital output you must  
set the digital output selector to on. This will  
deactivate the variable pitch slider and the pitch  
bend buttons or pitch wheel. If you were able to  
adjust the pitch, other devices will not read the  
digital output properly.  
i) PITCH - Is lit when the PITCH BUTTON is active.  
j) TIME BAR - Shows either time remaining or elapsed  
depending on the setting of the TIME BUTTON (4).  
k) PITCH - Shows the percentage change in pitch.  
l) TRACK - Shows the track that the unit  
is playing with.  
m) MINUTES - Shows the minutes elapsed  
or remaining depending on mode  
setting.  
n) SECONDS - Shows the seconds  
elapsed or remaining depending on  
mode setting.  
o) FRAMES - The CD Player breaks down  
a second into 75 frames for accurate  
cueing. This shows the frames elapsed  
or remaining depending on mode  
setting.  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 9 -  
CDN-32S  
DESCRIPTION OF THE PLAY/PAUSE AND CUE OPERATIONS  
PLAY and CUE  
Pressing the “PLAY/PAUSE” button starts the disc. Pressing the “CUE” button will reset the disc to  
the last place where the disc was started. This is called the cue point. By alternately pressing the  
“PLAY/PAUSE” button and the “CUE” button, the disc may be returned and played from the cue point  
any number of times. This function is called back cue.  
PLAY, PAUSE and CUE  
EDITING CUE POINT  
When the inner search dial is turned  
while a cue point is set, a new cue  
point can be located. The CD player  
will repeatedly play small parts of the  
CD as you move it to the desired  
position. By pressing “PLAY/PAUSE”  
then “CUE” you can confirm that this  
new cue point is desirable  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 10 -  
CDN-32S  
MATCHING THE BEATS PER MINUTE (BPM)  
Match the tempo by monitoring the music of both PLAYER 1 and PLAYER 2 by ear and adjusting the  
pitch. When the tempo of the music of the selected CD player is slow compared to the tempo of the  
other player, move the slider to the ( + ) side and match the tempo. When faster, move the pitch  
slider to the ( - ) side. The following description is for the case of matching the pitch of PLAYER 2 to  
the pitch of the music being played on PLAYER 1.  
Press PLAY/PAUSE to start PLAYER 1  
PLAYER 1 is playing  
Press PLAY/PAUSE to start PLAYER 2  
Both CD players are playing discs.  
Listen to PLAYER 2 in your headphones  
When PLAYER 2 is slow  
compared to PLAYER 1  
speed up PLAYER 2  
When PLAYER 2 is fast  
compared to PLAYER 1  
slow down PLAYER 2  
BEAT MATCHING USING PITCH BEND  
If you find the BPM’s (Beats Per Minute or Tempos) are the same, however, the drum beats are not  
matched you will need to temporarily change the pitch. This description is for the case of matching  
the beat of PLAYER 2 to the beat of the music being played on PLAYER 1. (This procedure can be  
done on either PLAYER).  
After matching the BPM’s adjust the pitch temporarily as follows:  
When PLAYER 2 is ahead press the  
or rotate the jog wheel counter clockwise  
When PLAYER 2 is behind press the  
or rotate the jog wheel clockwise  
or  
or  
The pitch changes automatically while the  
or  
button is being pressed or the jog wheel is  
rotated. The faster you rotate the wheel the more you change. Releasing the button or wheel results  
in a return to the original pitch. (So the BPM’s are once again the same.)  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 11 -  
CDN-32S  
RELAY PLAY  
The cables required are commercially available 3.5mm (1/8”) mini-plug cables. One has already  
been included with your unit so the relay function could be used.  
1. Connect auto start cable between both sides of the remote unit.  
2. Insert CDs into both sides of the unit.  
3. Hold down the time buttons for 1-2 seconds until the display  
indicates “auto” and the track number begins to flash. The track  
number will flash while the mode is active. Both sides must be  
active for relay to work.  
4. Put both sides in SINGLE play mode while learning this function.  
5. Press play on CD1 of the unit. When that CD1 has finished play it will send a signal to CD2 to  
start play. You will see CD2 start play and CD1 pause and cue to the beginning of the next track.  
When CD2 has completed play CD1 will start.  
Note: The play command is sent at the end of specified play. If the unit is in SINGLE mode the play  
command will start at the end of the track. If the unit is in CONTINUOUS mode the play command  
will be sent at the end of the full CD. Two CDs will play continuously, alternating from side to side.  
This feature will also work in program mode, however, if the sides are also in SINGLE mode the same  
number of tracks programmed should be the same. Play will stop at the end of the last track.  
FADER-START MODE  
This mode is achievable by attaching both sides of your CD player to a similarly equipped DJ mixer.  
1. Connect cables between the CD remote unit and your DJ mixer.  
2. Hold down the time button for 1-2 seconds to activate the fader start capability.  
3. Follow the directions in your mixer manual  
Typically if you move the crossfader toward the active channel, the attached CD player will activate.  
When it is moved away that side will cue, (similar to pressing the cue button).  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 12 -  
CDN-32S  
EXAMPLE OF MIXING USING BOTH PLAYERS OF YOUR CD PLAYER  
While playing a disc on PLAYER 1 load a disc into PLAYER 2 and select your next track, match its  
pitch to the track playing on PLAYER1 and when you are ready use the crossfader on your mixer to  
fade from PLAYER 1 to PLAYER 2.  
PLAYER 1  
PLAYER 1  
PLAYER 1  
Load a disc in PLAYER 1  
and select the track and  
press PLAY.  
Load a disc and press the  
OPEN/CLOSE button.  
Select the track to be  
played.  
Press the PLAY button  
PLAYER 2  
PLAYER 2  
PLAYER 2  
Load a disc in PLAYER 2  
and select the track then  
play.  
Load a disc and press the  
OPEN/CLOSE button.  
Select the track to be  
played.  
Press the PLAY button  
PLAYER 2  
PLAYER 2  
PLAYER 2  
Set and edit a start cue  
point on PLAYER 2  
Press the Pause button of  
PLAYER 2.  
Rapidly search for a cue  
point using the outer wheel  
Slowly set the right point  
using the inner wheel  
PLAYER 2  
PLAYER 2  
PLAYER 2  
Check you new cue point  
Listen with the monitor and  
press the play button.  
Press the cue button then  
play to be sure of the set  
cue point.  
Set the player to the Cue  
point by pressing Cue  
PLAYER 2  
PLAYER 2  
MIXER  
Do a MIX!  
With a matching downbeat  
from Player 1 press the  
play button.  
If you are beat mixing turn  
on your Pitch adjust and  
follow the directions for  
beat matching.  
When you are happy with  
you mix adjust you mixer  
accordingly.  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 13 -  
CDN-32S  
BEFORE SWITCHING OFF THE POWER:  
When you have finished using the CD player, be sure that the disc tray is closed with the  
“OPEN/CLOSE” button before switching off the power.  
DO NOT switch off the power when  
Switch off the power after the  
disc holder has been closed  
with the “OPEN/CLOSE” button  
the disc holder is open.  
TROUBLESHOOTING:  
Symptom  
Possible Cause  
Corrective Action  
The power fails to switch on  
when the POWER switch is set  
to on  
Poor power plug connection at  
the AC outlet or IEC Power cord the AC outlet and make sure  
loose from rear of unit connection is good in unit rear  
Insert the power plug firmly into  
Disc play does not start  
The disc is loaded upside down Reload the disc with the label  
side up  
The disc is too dirty  
Clean the disc  
No sound  
Improper output cable  
connections  
Connect the output cables  
correctly  
Improper amplifier operation  
Check amplifier setup  
Sound skips  
The CD player is subject to  
vibrations or physical shock  
Change the installation location  
The disc is too dirty  
Clean the disc  
Programmed disc play will not  
function  
The CD player is in normal disk Hold down the Program button  
play mode  
for 3 seconds then program the  
tracks  
Hum  
Loose cable connections  
Firmly connect all audio plugs  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 14 -  
CDN-32S  
SPECIFICATIONS  
TECHNICAL  
Quantization  
Oversampling rate  
16-bit linear/channel, 3 beam laser  
8 times  
Frequency response 20Hz-20KHz  
Channel separation  
T.H.D. + NOISE  
S/N ratio (IHF-A)  
Output level  
86dB  
0.01%  
94dB  
2.0Vrms  
Short access time  
(Play next track)  
Long access time  
less than 1.7sec  
(Track 1 ->Track 20) less than 3sec  
Instant start  
less than .015 sec  
Pitch control range  
Pitch bend  
+/-12%  
+/-16%  
Digital Output  
type 2, form 1, S/PDIF (Sony/Phillips Digital Interface Format)  
GENERAL  
Dimensions:  
Main Unit: 482 (W) x 88.8 (H) x 264 (D) mm (without feet)  
19 (W) x 3.5 (H) x 10 3/8 (D) inches (without feet)  
Control Unit: 482 (W) x 88.8 (H) x 74 (D) mm (without feet)  
19 (W) x 3 1/2 (H) x 2 7/8 (D) inches (without feet)  
Weight:  
Player Unit: 5 Kgs., 11 lbs.  
Control Unit: 2 Kgs., 4.4 lbs.  
Power Supply:  
115/230V AC, 50/60Hz  
Power Consumption:  
25W  
- The Leader in DJ Technology  
©1999 Numark Industries  
- 15 -  
®
Professional Disc Jockey Products  
LIMITED PRODUCT WARRANTY  
1. What is covered and for how long? NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK'S DJ mixers and amplifiers are  
free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized  
NUMARK dealer and continuing for the following period of time after that date for (2) Years. The warranty is extended to (3) Years with the completion of the  
warranty card provided that the warranty card is completed and returned within (30) days from the date of purchase. All other NUMARK products are warranted  
for (1) Year including but not limited to CD players, turntables, preamplifiers, beatkeepers, equalizers, microphones, headphones, and all other accessories.  
2. What is not covered? This Limited Warranty is conditioned upon proper use of the product by the purchaser.  
This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical or electrical stress,  
modification of any part of the product, or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c) all plastic surfaces  
and other externally exposed parts that are scratched or damaged due to normal use; (d) defects or damage from improper testing, operation,  
maintenance, installation, adjustment, or service of the mixers; (e) crossfaders.  
3. What are NUMARK'S obligations? During the applicable warranty period, NUMARK will repair or replace, at NUMARK'S sole discretion, without charge to the  
purchaser, any defective component part of the mixer. To obtain service under this Limited Warranty, purchaser must first contact NUMARK and obtain a return  
authorization number ("RA#"). Purchaser must then return the mixer to NUMARK in an adequate container for shipping, accompanied by purchaser's sales  
receipt or comparable proof of sale showing the date of purchase, the serial number of the product, and the seller's name and address. To obtain an RA# and  
assistance on where to return the mixer, contact NUMARK customer service at 401-295 9000. Upon receipt, NUMARK will repair or replace the defective  
products. NUMARK may, at NUMARK'S sole discretion, use rebuilt, reconditioned, or new parts or components when repairing any product or replace a  
product with a rebuilt, reconditioned or new product. Repaired mixers will be warranted for a period equal to the remainder of the original Limited Warranty on  
the original mixer or for (90) days, whichever is longer. All replaced parts, components, boards and equipment become the property of NUMARK. If NUMARK  
determines that any mixer is not covered by this Limited Warranty, purchaser must pay all parts, shipping, and labor charges for the repair or return of such  
mixer.  
4. What are the limits on NUMARK'S liabilities? THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY, TOGETHER WITH ANY IMPLIED WARRANTIES  
COVERING NUMARK MIXERS, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR  
PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, NUMARK  
SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO  
PURCHASER'S PROPERTY, OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY NUMARK  
MIXER, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT LIMITED TO NUMARK'S OWN NEGLIGENCE, EVEN IF NUMARK OR ITS  
AGENT HAS BEEN ADVISED OF SUCH DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY. THIS LIMITED  
WARRANTY IS THE COMPLETE WARRANTY FOR NUMARK'S MIXERS, AND IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THIS  
LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER'S  
EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL  
ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH  
PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.  
This Limited Warranty allocates risk of product failure between purchaser and NUMARK, and NUMARK'S product pricing reflects this allocation of risk and the  
limitations of liability contained in this Limited Warranty. The agents, employees, distributors, and dealers of NUMARK are not authorized to make modifications  
to this Limited Warranty, or make additional warranties binding on NUMARK. Accordingly, additional statements such as dealer advertising or presentation,  
whether oral or written, do not constitute warranties by NUMARK and should not be relied upon.  
5. How does state law apply to this warranty? SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES OR HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER.  
6. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary from one jurisdiction to another.  
RETURN INFORMATION  
·
·
·
·
A Return Authorization number must be obtained from Numark through the address or phone numbers below.  
A copy of the original sales receipt must also be included for the equipment to be repaired under warranty.  
The faulty equipment must be packed in its original packaging.  
One additional outer layer of packaging must be included to ensure product safety. Failure to do so may inadequately protect the equipment in transit and,  
therefore, jeopardize the customer’s warranty.  
·
·
Numark will not accept COD shipments and no call tags will be issued for merchandise return.  
Numark will not return repaired merchandise to customers by priority service, unless by written request at the customer’s cost. Requests must be submitted in  
writing with merchandise returned.  
·
The defective Numark equipment should be sent, FREIGHT PREPAID with Return Authorization number clearly printed on the outer packaging and original  
sales receipt enclosed to:  
INDUSTRIES  
Attention: Service Department  
11 Helmsman Avenue  
North Kingstown, RI 02852 USA  
Phone: +1 (401) 295-9000  
Fax::  
+1 (401) 295-5200  
Web:  

Tripp Lite NS2000SR User Manual
Transcend Information StoreJet TS500GSJ25M User Manual
Toshiba G500 User Manual
Superior W550C User Manual
Sony Xplod CDX F5500 User Manual
Sony Ericsson W890i User Manual
Sony CD Player CDX L380X User Manual
Samsung SH B083L User Manual
Oster Coffeemaker PSTX Series User Manual
Numark Industries CDN 20S User Manual