Melitta ME2TMDS User Manual

READ AND SAVE THESE INSTRUCTIONS  
Coffee Maker  
IMPORTANT SAFEGUARDS  
When using electrical appliances, basic safety precautions should  
always be followed, including the following:  
• Read all instructions.  
• Do not touch hot surfaces. Use handles or knobs.  
To protect against electric shock, do not place cord, plugs, or  
appliance in water or other liquid.  
• Close supervision is necessary when any appliance is used by  
or near children.  
• Unplug from outlet when not in use and before cleaning. Allow  
to cool before putting on or taking off parts, and before cleaning  
the appliance.  
• Do not operate any appliance with a damaged cord or plug or  
after the appliance malfunctions, or has been damaged in any  
manner. Contact Consumer Service for examination, repair or  
adjustment.  
• The use of an accessory not evaluated for use with this  
appliance may cause injuries.  
• Do not use outdoors.  
• Do not let cord hang over edge of table or counter, or touch hot  
surfaces.  
• Do not place on or near a hot gas or electric burner, or in a  
heated oven.  
To disconnect, press the Power Switch with LED Indicator Light  
so that the light is off, then remove plug from wall outlet.  
• Do not use appliance for other than intended use.  
• Be certain lids are securely in place before operating appliance.  
• Scalding may occur if the lid is removed during the brewing  
cycles.  
SAVE THESE INSTRUCTIONS  
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.  
3
ADDITIONAL IMPORTANT  
SAFEGUARDS  
WARNING: This appliance generates heat and escaping steam  
during use. Use proper precautions to prevent the risk of burns,  
fires, or other injury to persons or damage to property.  
• All users of this appliance must read and understand this  
Owner’s Manual before operating or cleaning this appliance.  
• The cord to this appliance should be plugged into a 120V AC  
electrical outlet only.  
• Use water only in this appliance! Do not put any other liquids  
or food products in this appliance. Do not mix or add anything  
to the water placed in this appliance, except as instructed in the  
User Maintenance Instructions to clean the appliance.  
• DO NOT attempt to move an appliance containing hot liquids.  
Allow appliance to cool completely before moving.  
• Keep appliance at least 4 inches away from walls or other  
objects during operation. Do not place any objects on top of  
appliance while it is operating. Place the appliance on a surface  
that is resistant to heat.  
• If this appliance begins to malfunction during use, immediately  
unplug the cord. Do not use or attempt to repair the  
malfunctioning appliance.  
• If this appliance falls or accidentally becomes immersed in  
water or any other liquid, unplug it immediately. Do not reach  
into the water! Do not use this appliance after it has fallen  
into or has become immersed in water. Contact Consumer  
Service for examination and repair.  
• Do not leave this appliance unattended during use.  
• The appliance must be left to cool down sufficiently before  
adding more water to avoid splattering.  
• Always use fresh, cool water in your appliance. Warm water or  
other liquids, except as listed in cleaning section, may cause  
damage to the appliance.  
• DO NOT lift Filter Basket Lid until brewing is complete, and all  
parts have cooled.  
• The Mugs are designed for use with this appliance. They must  
never be used on a range top.  
• DO NOT put mugs into a microwave.  
4
CAUTION: A short power supply cord is provided to reduce the  
risk resulting from becoming entangled in or tripping over a longer  
cord. Do not use an extension cord with this product.  
POLARIZED PLUG: This appliance has a polarized plug, (one  
blade is wider than the other). To reduce the risk of electric shock,  
this plug is intended to fit in a polarized outlet only one way. If the  
plug does not fit fully in the outlet, reverse the plug. If it still does  
not fit, contact a qualified electrician. Do not attempt to modify the  
plug in any way.  
CAUTION: To prevent Plasticizers from migrating from the finish of  
the countertop or tabletop or other furniture, place NON-PLASTIC  
coasters or placemats between the appliance and the finish of the  
countertop or tabletop.  
Failure to do so may cause the finish to darken, permanent  
blemishes may occur or stains can appear.  
ELECTRIC POWER: If the electric circuit is overloaded with other  
appliances, your appliance may not operate properly. It should be  
operated on a separate electrical circuit from other appliances.  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC  
SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER-  
SERVICABLE PARTS INSIDE. REPAIR SHOULD BE DONE BY  
AUTHORIZED SERVICE PERSONNEL ONLY.  
Before Using Your Take 2™  
Programmable Clock Timer  
Coffee Maker  
Before using your Take 2Programmable Clock Timer Coffee  
Maker for the first time, we suggest you become familiar with all of  
its parts. Read all instructions and cautions carefully.  
CAUTION: Press the Power Switch with LED Indicator Light so  
that the light is off. Unplug from outlet.  
IMPORTANT: Never place Thermal Mugs on a hot stove or in a  
microwave. Never let Thermal Mugs stand in water.  
Before brewing coffee, follow instructions for cleaning. See “Care  
and Cleaning,page 8.  
CAUTION: Do not immerse cord, plug, or coffee maker unit in  
water or other liquids.  
5
Your product may vary slightly from illustration.  
Parts Identification  
Filter Basket  
(P/N 31142)  
Water Chamber  
with Water Level  
Indicator  
Filter  
Basket  
Holder  
Mug Lid(s)  
(P/N 30909)  
Flow Nozzle  
(P/N 31144)  
FIGURE B  
Thermal Mugs  
(P/N 30911)  
Drip Tray  
(P/N 31145)  
Overflow  
Tray  
(P/N 31143)  
Base  
FIGURE A  
FIGURE C  
FIGURE D  
FIGURE E  
6
Setting the Clock  
1. Plug into 120 V~60 Hz outlet.  
2. The display will go to AM 12:00 and continue to flash until you  
press a button.  
3. Press the Program button, “SET TIME” will be displayed in the  
top right corner.  
4. Press and hold the HR button for rapid hour advancement.  
When the desired hour is reached, release the button.  
5. Press and hold the MIN button for rapid minute advancement.  
When the desired minute is reached, release the button.  
6. Press the PROG button again. The time is now set. If you do  
not press the PROG button again, the display will  
automatically return to the time of day after 10 seconds.  
Brewing  
1. Plug into 120V ~ 60 Hz outlet.  
2. Make sure unit is in the OFF position. The LED Indicator Light  
will be off.  
IMPORTANT: Place coffee maker on a level surface.  
3. Markings on the Water Level Indicator indicate the amount of  
water required to brew the desired number of Thermal Mugs.  
Lift up the hinged Water Chamber Lid and fill to desired level  
with cold, fresh water for the number of Thermal Mugs (one or  
two), using the Water Level Indicator on the Water Window.  
WARNING: When making one Thermal Mug, do not fill above  
level 1.  
IMPORTANT: If cream or milk will be added to Thermal Mugs,  
use less water for brewing.  
4. For optimal holding temperature, rinse the inside of Thermal  
Mugs with warm water before brewing. Place Lids securely on  
tops of Thermal Mugs. Press down on the Lids to ensure  
proper fit.  
NOTE: You can brew either one Thermal Mug or two Thermal  
Mugs at once. Place Thermal Mugs snugly on Base of unit as  
shown in Figure A (for two Thermal Mugs). The contoured  
design on the Base should be used as a guide for Thermal  
Mug alignment.  
5. Insert a #2 paper cone filter into the Removable Filter Basket  
and add coffee grounds. Use approximately 12-2 tablespoons  
for each Thermal Mug of coffee. Close Water Chamber Lid,  
snapping the Basket into place. (See Figure D.)  
7
6. Press Power Switch ON. The LED Indicator Light will turn red.  
CAUTION: Avoid contact with heated water.  
IMPORTANT: Do not remove Thermal Mugs until the LED  
Indicator Light has turned OFF. The LED Indicator Light will  
turn OFF approximately two minutes after brewing is  
complete. This delay will allow the last drops of coffee to flow  
into the Thermal Mugs.  
7. After LED Indicator Light turns off, Thermal Mugs may be  
safely removed.  
8. If brewing more than one cycle, allow unit to cool for 10  
minutes between cycles.  
Helpful Hints for Brewing  
• Always use fresh, cold water for brewing. In areas with hard  
water or where water contains a high mineral content, use cold  
filtered water for optimal coffee taste.  
• For best results, use Melitta® #2 paper cone filters and Melitta®  
Premium Coffee.  
• The markings on the Water Level Indicator reflect the quantity  
of fresh water to be used. The quantity of brewed coffee is less  
because the coffee grounds absorb water.  
Programming a Delayed Brew  
1. Press the PROG button twice, “SET TIMER” will be displayed  
in the bottom center of the Display Window.  
2. Using the HR and MIN button, set the time you wish the coffee  
to begin brewing. Once the time is set, the display will return  
to the time of day automatically after 8 seconds, and then  
“SET TIMER” will disappear. You may also press the PROG  
button to make the display return to the time of day.  
3. Press AUTO button, LED Indicator Light will be green to  
indicate the timer has been set for delayed start.  
Note:To cancel the delayed start, press AUTO once again, the  
LED Indicator Light will go off and the delayed start program  
will be cancelled.  
4. When the delayed start program has reached the preset time,  
the LED Indicator Light will change to red and the brewing will  
start.  
Note: During the auto-brew program, you may start brewing at  
once by pressing the ON/OFF button.  
8
Care and Cleaning  
1. Make sure Power Switch is in the OFF position. The LED  
Indicator Light will be off.  
2. Unplug and allow to cool completely before cleaning.  
3. Open Filter Basket Holder and lift up on the tab of Filter  
Basket. Discard any paper filter and coffee grounds.  
4. Wash removable Filter Basket, Drip Tray and Overflow Tray,  
Mugs and Mug Lids in warm, soapy water. Rinse and dry  
thoroughly. Or, you may wash the Mugs and Lids in the top  
rack of a dishwasher.  
5. Clean the outside of the coffee maker with a damp cloth.  
CAUTION: DO NOT IMMERSE CORD, PLUG OR COFFEE  
MAKER UNIT IN WATER OR OTHER LIQUID.  
6. Replace Filter Basket, Drip Tray and Overflow Tray for next use.  
Descaling  
We recommend that you descale your coffee maker once a month  
because mineral deposits can form a coating in the coffee maker,  
causing slower brewing time and possibly an off flavor in the  
coffee. Use a cleaner recommended for coffee makers. To descale  
your unit:  
1. Pour two ounces of vinegar or coffee cleaner into the Water  
Chamber. Add cold water to the level 2 indicator.  
2. Place a clean #2 paper cone filter in the filter basket and close  
Water Chamber Lid. Place both Mugs in proper position on  
Base of unit.  
3. Follow “Brewing” instructions (without coffee).  
4. When the LED Indicator Light turns off, wait 15 minutes and  
pour solution from Mugs back into coffee maker. Be sure that  
the Filter Basket is still in proper position.  
5. Turn unit on again. Allow all solution to empty into Mugs.  
When LED Indicator Light turns off, discard solution.  
6. Allow unit to cool 10 minutes. To rinse unit, fill Water Chamber  
with fresh, cold water up to the level 2 indicator. Insert a fresh  
paper filter into Filter Basket. Close Water Chamber Lid. Place  
both Mugs in proper position on Base of unit and turn Power  
Switch on.  
7. At end of cycle, allow unit to cool, discard water and paper  
filter. Wash and dry Mugs and other removable parts.  
8. Unplug coffee maker from outlet. When coffee maker has  
cooled, wipe exterior with a damp cloth.  
9
IMPORTANT NOTICE  
If any parts are missing or defective,  
DO NOT return this product.  
Please call our Customer Relations Department for assistance.  
800-233-9054 Monday - Friday 9am - 5pm CST  
LIMITED ONE YEAR WARRANTY  
Warranty: This Melitta® product is warranteed by Salton, Inc. to be free from defects  
in materials or workmanship for a period of (1) year from the original purchase date.  
This product warranty covers only the original consumer purchaser of the product.  
Warranty Coverage: This warranty is void if the product has been damaged by  
accident in shipment, unreasonable use, misuse, neglect, improper service,  
commercial use, repairs by unauthorized personnel, normal wear and tear, improper  
assembly, installation or maintenance abuse or other causes not arising out of  
defects in materials or workmanship. This warranty is effective only if the product is  
purchased and operated in the USA, and does not extend to any unit which has been  
used in violation of written instructions furnished with the product, or to units which  
have been altered or modified, or to damage to products or parts thereof which have  
had the serial number removed, altered, defaced or rendered illegible.  
Implied Warranties: ANY IMPLIED WARRANTIES WHICH THE  
PURCHASER MAY HAVE ARE LIMITED IN DURATION TO ONE (1) YEAR FROM  
THE DATE OF PURCHASE. Some states do not allow limitations on how long an  
implied warranty lasts, so the above limitation may not apply to you.  
Warranty Performance: During the above one-year warranty period, a product with  
a defect will be either repaired or replaced with a reconditioned comparable model  
(at our option) when the product is returned to the Repair Center, or the purchase  
price refunded. The repaired or replacement product will be in warranty for the  
balance of the one-year warranty period and an additional one-month period. No  
charge will be made for such repair or replacement.  
Service and Repair: Should the appliance malfunction, you should first call toll-free  
1-800-233-9054 between the hours of 9:00 am and 5:00 pm Central Standard Time  
and ask for CONSUMER SERVICE stating that you are a consumer with a problem.  
Please refer to model number ME2TMDS when you call.  
In-Warranty Service (USA): For an appliance covered under the warranty period, no  
charge is made for service or postage. Call for return authorization 1-800-233-9054.  
Out-of Warranty Service: A flat rate charge by model is made for out-of-warranty  
service. Include $8.00 (U.S.) for return shipping and handling. We will notify you by  
mail of the amount of the charge for service and require you to pay in advance for  
the repair or replacement.  
10  
For Products Purchased in the USA, but Used in Canada: You may return the  
product insured, packaged with sufficient protection, and postage and insurance  
prepaid to the USA address listed below. Please note that all customs duty /  
brokerage fees, if any, must be paid by you and we will require you to pay the cost of  
customs duty / brokerage fees to us in advance of our performing any service.  
Risk During Shipment: We cannot assume responsibility for loss or damage  
during incoming shipment. For your protection, carefully package the product for  
shipment and insure it with the carrier. Be sure to enclose the following items with  
your appliance: any accessories related to your problem, your full return address and  
daytime phone number, a note describing the problem you experienced, a copy of  
your sales receipt or other proof of purchase to determine warranty status. C.O.D.  
shipments cannot be accepted.  
To return the appliance, ship to:  
Attn: Repair Center  
To contact us, please write, call or email:  
Salton, Inc.  
Salton, Inc.  
P.O. Box 6916  
708 South Missouri Street  
Macon, MO 63552  
Columbia, MO 65205-6916  
1-800-233-9054  
Limitation of Remedies: No representative or person is authorized to assume for  
Salton, Inc. any other liability in connection with the sale of our products. There shall  
be no claims for defects or failure of performance or product failure under any theory  
of tort, contract or commercial law including, but not limited to negligence, gross  
negligence, strict liability, breach of warranty and breach of contract. Repair,  
replacement or refund shall be the sole remedy of the purchaser under this warranty,  
and in no event shall Salton, Inc. be liable for any incidental or consequential  
damages, losses or expenses. Some states do not allow the exclusion or limitation  
of incidental or consequential damages, so the above limitation or exclusion may not  
apply to you.  
Legal Rights: This warranty gives you specific legal rights, and you may also have  
other rights which vary from state to state.  
© 2004 Salton, Inc.  
All Rights Reserved  
P/N 61575  
Printed in China  
11  

Mr Coffee BVMC KG1 User Manual
LG Electronics KG300 User Manual
iHome iP47 User Manual
HTC P6500 User Manual
Hitachi Travelstar HTS725040A9A364 User Manual
Franklin Modem+Disk CDU 680DOrA User Manual
Epson RX 8581NB User Manual
Disney DCR5500 C User Manual
Bunn VP17 2 User Manual
Bloomfield 8372 User Manual