Zanussi Washer ZWH7120 P User Manual

EN  
User manual ............... 2  
............... 25  
CN  
Washing machine  
ZWH7120 P  
147214520  
 
Garments which have been in contact with  
volatile petroleum products should not be  
machine washed. If volatile cleaning fluids  
are used, care should be taken to ensure  
that the fluid is removed from the garment  
before placing in the machine.  
Installation  
This appliance is heavy. Care should be  
taken when moving it.  
When unpacking the appliance, check that  
it is not damaged. If in doubt, do not use it  
and contact the Service Centre.  
Never pull the power supply cable to remove  
the plug from the socket; always take hold of  
the plug itself.  
All packing and transit bolts must be  
removed before use. Serious damage can  
occur to the product and to property if this  
is not adhered to. See relevant section in  
the user manual.  
Never use the washing machine if the power  
supply cable, the control panel, the working  
surface or the base are damaged so that the  
inside of the washing machine is accessible.  
After having installed the appliance, check  
that it is not standing on the inlet and drain  
hose and the worktop is not pressing the  
electrical supply cable.  
Child safety  
If the machine is situated on a carpeted  
floor, please adjust the feet in order to allow  
air to circulate freely.  
This washing machine is not intended for  
use by young children or infirm persons  
without supervision.  
Always be sure, that there is no water  
leakage from hoses and their connections  
after the installation.  
Young children should be supervised to  
ensure that they do not play with the  
appliance.  
Any plumbing work required to install this  
appliance should be carried out by a  
qualified plumber.  
The packaging components (e.g. plastic film,  
polystyrene) can be dangerous to children -  
danger of suffocation! Keep them out of  
childrens reach  
Any electrical work required to install this  
appliance should be carried out by a  
qualified electrician.  
Keep all detergents in a safe place out of  
childrens reach.  
Make sure that children or pets do not climb  
into the drum. To avoid this the machine  
incorporates special feature.  
Use  
This appliance is designed for domestic  
use. It must not be used for purposes other  
than those for which it was designed.  
To activate this  
device, rotate the  
button (without  
pressing it) inside  
the door clockwise  
until the groove is  
horizontal. If  
Only wash fabrics which are designed to be  
machine washed. Follow the instructions on  
each garment label.  
Do not overload the appliance. See the  
relevant section in the user manual.  
necessary use a  
coin.  
Before washing, ensure that all pockets are  
empty and buttons and zips are fastened.  
Avoid washing frayed or torn articles and  
treat stains such as paint, ink, rust, and  
grass before washing. Underwired bras  
must NOT be machine washed.  
To disable this device and restore the  
possibility of closing the door, rotate the  
button anti-clockwise until the groove is  
vertical.  
3
 
Environment concerns  
With adequate pre-treatment, stains and  
limited soiling can be removed; the laundry  
can then be washed at a lower temperature.  
Packaging materials  
The materials marked with the symbol  
recyclable.  
are  
Measure out detergent according to the  
water hardness, the degree of soiling and the  
quantity of laundry being washed.  
>PE<=polyethylene  
>PS<=polystyrene  
>PP<=polypropylene  
This means that they can be recycled by  
disposing of them properly in appropriate  
collection containers.  
Old machine  
Use authorised disposal sites for your old  
appliance. Help to keep your country tidy!  
The symbol  
on the product or on its  
packaging indicates that this product may not  
be treated as household waste. Instead it shall  
be handed over to the applicable collection  
point for the recycling of electrical and  
electronic equipment.  
By ensuring this product is disposed of  
correctly, you will help prevent potential  
negative consequences for the environment  
and human health, which could otherwise be  
caused by inappropriate waste handling of this  
product.  
For more detailed information about recycling  
of this product, please contact your local city  
office, your household waste disposal service  
or the shop where you purchased the product.  
Ecological hints  
To save water, energy and to help protect the  
environment, we recommend that you follow  
these tips:  
Normally soiled laundry may be washed  
without prewashing in order to save  
detergent, water and time (the environment  
is protected too!).  
The machine works more economically if it is  
fully loaded.  
4
 
Product description  
Front View  
Back View  
1
2
3
8
9
4
5
6
10  
12  
11  
7
13  
11  
1
6
7
8
9
Detergent Dispenser Drawer  
Worktop  
Rating Plate  
Water Drain Hose  
2
3
4
5
12  
13  
Hose Holders  
Back Feet  
Front Feet  
Control Panel  
Water Inlet Hose  
Drain Hose Support  
Mains Cable  
Door Opening Handle  
Drain Filter  
10  
Technical data  
Dimensions  
60 cm  
85 cm  
54 cm  
Width  
Height  
Depth  
Power supply voltage/frequency  
Total power absorbed  
220-240 V/50 Hz  
2000 W  
Minimum fuse protection  
10A  
Water supply pressure  
Maximum Load  
Minimum  
Maximum  
0,05 MPa  
0,8 MPa  
Cottons  
7.0 kg  
2.5 kg  
2.5 kg  
2.0 kg  
Synthetics  
Delicates  
Hand Wash  
Spin Speed  
Maximum :  
1200 rpm  
5
 
Installation  
Unpacking  
Important!  
Very carefully  
remove the front  
polystyrene block  
(B) by gently  
B
All transit bolts and packing must be  
removed before using the appliance.  
1
pulling the  
2
polyethylene bag  
(1) downwards  
then (2) out,  
ensuring not to  
tear the bag.  
You are advised to keep all transit devices so  
that they can be refitted if the machine ever has  
to be transported again.  
Using a spanner  
unscrew and  
remove the two  
rear bottom  
Some models are provided with a bottom  
cover that will be found inside the washing  
machine drum.  
screws.  
After ensuring the  
polyethylene bags  
2
have been  
removed, follow  
2
below instruction:  
Slide out the two  
plastic pins.  
1
C
(1).  
Locate the bottom cover as shown in  
position (C).  
(2).Then push the top end to lock to the  
bottom of washing machine.  
Remove the polystyrene base, set the  
machine upright and unscrew the remaining  
rear screw. Slide  
out the relevant  
pin.  
Lay the machine on its back ensuring that  
the hoses are not crushed.  
Place one of the  
polystyrene angle  
packings under  
the machine.  
Cover all the open  
holes with the  
plugs which you  
can find in the  
bag containing  
the instruction  
booklet.  
Remove the  
polystyrene block  
(A) protecting the  
motor.  
A
6
 
Positioning  
Install the machine on a flat hard floor.  
Water drainage  
The end of the drain hose can be positioned in  
three ways:  
Make sure that air circulation around the  
Hooked over the edge of a sink using the  
plastic hose guide supplied with the  
machine.  
machine is not impeded by carpets, rugs etc.  
Check that the machine does not touch the  
wall or cupboard units.  
In this case, make  
sure the end cannot  
come unhooked when  
the machine is  
Carefully level by  
screwing the  
adjustable front feet  
in or out.  
emptying.  
Never place cardboard, wood or similar  
materials under the machine to compensate  
for any unevenness in the floor.  
This could be done by tying it to the tap with a  
piece of string or attaching it to the wall.  
In a sink drain pipe branch. This branch  
must be above the trap so that the bend is  
at least 60 cm above the ground.  
Water inlet  
Connect the water inlet hose to a tap with  
3/4” BSP thread.  
Directly into a drain pipe at a height of not  
less than 60 cm and not more than 90 cm.  
Use the hose supplied with the washing  
machine. DO NOT USE OLD HOSES.  
The end of the drain hose must always be  
ventilated, i.e. the inside diameter of the drain  
pipe must be larger than the outside diameter of  
the drain hose.  
The other end of the inlet hose which  
connects to the machine can be turned in  
any direction.  
The drain hose must not be kinked. Run it along  
the floor; only the part near the drainage point  
must be raised.  
Simply loosen the fitting, rotate the hose and  
retighten the fitting, making sure there are no  
water leaks.  
For the correct functioning of the machine  
the drain hose must remain hooked on the  
proper support piece situated on the top  
part of back side of the appliance.  
The inlet hose must not be lengthened. If it is  
too short and you do not wish to move the  
tap, you will have to purchase a new, longer  
hose specially designed for this type of use.  
7
 
Electrical Connection  
Important!  
This machine is designed to operate on a  
220-240 V, single-phase, 50 Hz supply.  
Connect the machine to an earthed socket.  
The manufacturer declines any responsibility  
for damage or injury through failure to comply  
with the above safety precaution. Should the  
appliance power supply cable need to be  
replaced, this should be carried out by our  
Service Centre.  
“An incorrect power supply may void your  
warranty.”  
Check that your domestic electrical installation  
can take the maximum load required (2.0 kW),  
also taking into account any other appliances  
in use.  
First Use  
Run a cotton cycle at 90 °C, without any  
laundry in the machine, to remove any  
manufacturing residue from the drum and  
tub. Pour 1/2 a measure of detergent into  
the dispenser drawer and start the machine.  
Ensure that the electrical and water  
connections comply with the installation  
instructions.  
Daily Use  
Rub particularly soiled areas with a special  
detergent or detergent paste. Treat curtains  
with special care. Remove hooks or tie them  
up in a bag or net.  
Sorting the laundry  
Follow the wash code symbols on each  
garment label and the manufacturer’s washing  
instructions. Sort the laundry as follows: whites,  
coloureds, synthetics, delicates, woollens.  
Removing stains  
Before loading the laundry  
Stubborn stains may not be removed by just  
water and detergent. It is therefore advisable to  
treat them prior to washing.  
Never wash whites and coloureds together.  
Whites may lose their “whiteness” in the  
wash.  
New coloured items may run in the first  
wash; they should therefore be washed  
separately the first time.  
Blood: treat fresh stains with cold water. For  
dried stains, soak overnight in water with a  
special detergent then rub in the soap and  
water.  
Make sure that no metal objects are left  
in the laundry (e.g. coins, hair clips,  
safety pins, pins).  
Oil based paint: moisten with benzine stain  
remover, lay the garment on a soft cloth and  
dab the stain; treat several times.  
Remove persistent stains before washing.  
Dried grease stains: moisten with turpentine,  
lay the garment on a soft surface and dab the  
stain with the fingertips and a cotton cloth.  
Button up pillowcases, close zip fasteners,  
hooks and poppers. Tie any belts or long  
tapes.  
8
 
Rust: oxalic acid dissolved in hot water or a  
rust removing product used cold. Be careful  
with rust stains which are not recent since the  
cellulose structure will already have been  
damaged and the fabric tends to hole.  
Cotton, linen: drum full but not too tightly  
packed;  
Synthetics: drum no more than half full;  
Delicate fabrics and woollens: drum no  
more than one third full.  
Mould stains: treat with bleach, rinse well  
Washing a maximum load makes the most  
efficient use of water and energy.For heavily  
soiled laundry, reduce the load size.  
(whites and fast coloureds only).  
Grass: soap lightly and treat with bleach  
(whites and fast coloureds only).  
Ball point pen and glue: moisten with  
acetone (*), lay the garment on a soft cloth and  
dab the stain.  
Detergents and additives  
Good washing results also depend on the  
choice of detergent and use of the correct  
quantities to avoid waste and protect the  
environment. Although biodegradable,  
detergents contain substances which, in large  
quantities, can upset the delicate balance of  
nature.  
Lipstick: moisten with acetone (*) as above,  
then treat stains with methylated spirits.  
Remove any residual marks from white fabrics  
with bleach.  
Red wine: soak in water and detergent, rinse  
and treat with acetic or citric acid, then rinse.  
Treat any residual marks with bleach.  
The choice of detergent will depend on the type  
of fabric (delicates, woollens, cottons, etc.), the  
colour, washing temperature and degree of  
soiling.  
Ink: depending on the type of ink, moisten the  
fabric first with acetone (*), then with acetic  
acid; treat any residual marks on white fabrics  
with bleach and then rinse thoroughly.  
Only low suds Front load washer detergents  
should be used in this appliance:  
Tar stains: first treat with stain remover,  
methylated spirits or benzine, then rub with  
detergent paste.  
powder detergents for all types of fabric.  
powder detergents for delicate fabrics (60  
°C max) and woollens,  
(*) do not use acetone on artificial silk.  
liquid detergents, preferably for low  
temperature wash program (60 °C max) for  
all types of fabric, or special for woollens  
only.  
Load the laundry  
Open the door by carefully pulling the door  
handle outwards.  
The detergent and any additives must be  
placed in the appropriate compartments of the  
dispenser drawer before starting the wash  
program.  
Place the laundry in  
the drum, one item at  
a time, shaking them  
out as much as  
possible. Close the  
door.  
If using concentrated powder or liquid  
detergents, a program without prewash must  
be selected.  
Any fabric softener or starching additives must  
be poured into the compartment marked “  
before starting the wash program.  
Maximum loads  
Follow the product manufacturer’s  
recommendations on quantities to use and do  
not exceed the MAX mark in the detergent  
dispenser drawer.  
Recommended loads are indicated in the  
program charts. General rules:  
9
 
Do not spray stain pre-treatment products  
(e.g. Vanish) on or near the machine, as it  
can attack plastic materials reducing its life.  
Compartment  
used for washing powder or liquid.  
: this compartment is  
Compartment  
: this compartment is used  
for fabric conditioner and starching agent.  
Quantity of detergent to be used  
Aways add laundry detergents before switching  
the machine on and keep the dispenser clean  
and dry, so that the detergent can be efficiently  
dispensed from the unit.  
The type and quantity of detergent will depend  
on the type of fabric, load size, degree of soiling  
and hardness of the water used.  
Water hardness is classified in so-called  
“degrees” of hardness.  
Measure out the detergent and the  
fabric softener  
Information on hardness of the water in your  
area can be obtained from the relevant water  
supply company, or from your local authority.  
Measure out the amount of detergent required,  
pour it into the “main wash” compartment  
Follow the product manufacturers’ instructions  
on quantities to use.  
”.  
Not enough washing powder causes:  
for prewash  
the washload to turn grey,  
greasy clothes.  
for mainwash  
Too much washing powder causes:  
sudsing,  
reduced agitation and washing effect,  
inadequate rinsing.  
If you wish to carry out the “prewash” phase,  
pour it into the compartment marked “  
”.  
Use less detergent if:  
If required, pour fabric softener into the  
you are washing a small load,  
the laundry is lightly soiled,  
compartment marked  
must not exceed the “MAX” mark in the  
drawer).  
(the amount used  
large amounts of foam form during washing.  
Open the detergent dispenser drawer  
The detergent  
dispenser is  
for softener  
divided into three  
compartments.  
Close the drawer gently.  
Compartment  
: this compartment is only  
used for washing powder when a program  
has Prewash or Stain.  
10  
 
Control panel  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Program selector dial  
Temperature button  
Spin button  
Extra Rinse Button  
Display  
Start/Pause button  
Delay Start button  
Rinse Hold button  
Super Quick button  
11  
 
Set your washing program  
Program selector dial  
Turn the program selector dial to the required program. The  
green Start/Pause light starts to flash.  
The selector dial is divided into following sections:  
(Cancelling/Off)  
(Cottons)  
(Rinse)  
(Drain)  
(Spin)  
(Cottons Prewash)  
(Cottons Economy)  
(Easy Iron)  
(Blanket)  
(Mini 30)  
(Jeans)  
(Synthetics)  
(Mixed Fabric)  
(Delicates)  
(Wool/Handwash)  
The selector dial can be turned either clockwise or  
anticlockwise. Position “Off” to Reset program/Switching  
OFF the machine.  
At the end of the program the selector dial must be  
turned to position “Off”, to switch the machine off.  
Attention!  
If you turn the program selector dial to another program  
when the machine is working, the red Start/Pause pilot  
light will flash 3 times to indicate a wrong selection. The  
machine will not perform the new selected program.  
Cancelling a program  
Turn the selector dial to “Off” to cancel a program which is  
running. Now you can select a new program.  
Press this button repeatedly to increase or decrease the  
temperature, if you want your laundry to be washed at a  
temperature different from the one proposed by the  
washing machine.  
Temperature selector  
If a temperature is chosen that is not allowed with the  
selected program, the red pilot light of the Start/pause  
button will flash 3 times.  
12  
 
Press the Spin button repeatedly to change the spin speed,  
if you want your laundry to be spun at a speed different from  
the one proposed by the washing machine. The relevant  
light will light up.  
Spin Buttons  
Rinse Hold  
By selecting this option the water of the last rinse is not  
emptied out to prevent the fabrics from creasing.  
To empty out the water:  
turn the program selector dial to “Off”.  
select the Drain or Spin program.  
reduce the spin speed if needed, by means of the  
relevant button.  
depress Start/Pause button.  
This option can be used for lightly soiled in order to obtain  
a good washing result in a short time.  
Super Quick Buttons  
The washing time will be reduced according to type of  
fabric and the selected temperature.  
If an option is chosen that is not allowed with the selected  
program, the red pilot light of the Start/Pause button  
will flash 3 times.  
This option is recommended for people who are  
allergic to detergents, and in areas where the water is  
very soft.  
Extra Rinse Option  
The machine performs some additional rinses.  
The display shows the following information:  
Display  
Duration of the selected program.  
After selecting a program the duration is displayed in  
hours and minutes (for example 2.05).  
The duration is calculated automatically on the basis of the  
maximum recommended load for each type of fabric.  
13  
 
After the program has started, the time remaining is  
updated every minute.  
Display (continues)  
Delayed start  
The selected delay (20 hours max) set by means of the  
relevant button appears on the display for about 3  
seconds, then the duration of the previously selected  
program is displayed. The delay time value decreases by  
one unit every hour and then, when 1 hours remain, the  
time decreases every minute.  
Incorrect option selection  
If an option which is not compatible with the set wash  
programme is selected, the message  
is displayed  
for about 2 seconds and the integrated red Start/Pause  
light start flashing.  
Alarm codes  
In the event of operating problems, some alarm codes  
can be displayed, for example E20 (see paragraph  
“Something not working”).  
End of programme  
When the program has finished a flashing zero is  
displayed.  
Door open  
When the door has not been closed a flashing E40 is  
displayed.  
To start the selected program, press the “Start/Pause”  
button; the corresponding green pilot light stops  
flashing.  
Start/Pause button  
To interrupt a program which is running, depress the  
“Start/Pause” button: the corresponding green pilot  
light starts to flash.  
To restart the program from the point at which it was  
interrupted, press the “Start/Pause” button again.  
If you have chosen a delayed start, the machine will  
begin the countdown.  
Delay Start Button  
Before you start the program, this option makes it  
possible to delay the starting of the washing program by  
30 min - 60 min - 90 min, 2 hours and then by 1 hour till  
20 hours.  
The selected delay time will appear on the display for  
about 3 seconds, then the duration of the program will  
appear again.  
14  
 
The above options must be selected after choosing the  
wash program with the dial, and before pressing the  
Start/Pause button.  
Delay Start Button (continues)  
If after having set the delay start option (and pressed  
Start/Pause button) and you wish the cancel it,  
follow the below steps:  
set the washing machine to PAUSE by pressing the  
Start/Pause button;  
deselect the Delay start option, changing the status;  
press the Start/Pause button to start the program.  
Important!  
The selected delay can be changed only after selecting  
the washing program again.  
The door will lock through out the delay time.  
If you need to open the door, you must first set the  
washing machine to PAUSE by pressing the Start/Pause  
button, after that you need to wait about 2-3 minutes to  
release door lock, the Door Lock (  
) pilot light is  
flashing to show the door release is in process, pilot light  
switch off when the door can be opened.  
The “Child Lock” feature will allow you to lock the controls  
while the machine is running to prevent tampering.  
Child Lock Option (  
)
ACTIVATE “Child Lock” by pressing the “Temperature”  
and “Spin” buttons about 3 seconds, the padlock  
symbol “  
” is displayed on the screen.  
To DE-ACTIVE “Child Lock” simply press the “Temperature”  
and “Spin” buttons about 3 seconds, the “  
padlock  
symbol in the screen will disappear.  
Child Lock will remain activated until you de-activate it, even  
if the machine is turned off.  
The machine is provided of an acoustic device, which  
sounds in the following cases:  
Acoustic Signals Option  
when selecting a wash program  
when depressing the options buttons  
at the end of the cycle  
in the event of operating problems  
By pressing the “Rinse Hold” and “Super Quick” buttons  
simultaneously for about 3 seconds, the acoustic signal is  
deactivated (except for the events of operating problems).  
By pressing these 2 buttons again, the acoustic signal is  
reactivated.  
15  
 
Altering an option or a running program Opening the door after the program  
has started  
It is possible to change any option before the  
program carries it out. The option “Super Quick”  
cannot be modified after the Start/Pause has  
been pressed.  
If you need to open the door, you must first  
set the washing machine to PAUSE by  
pressing the Start/Pause button, after that  
you need to wait about 2-3 minutes to  
release door lock.  
Changing a running program is possible only  
by resetting it. Turn the program selector dial  
to “Off” and then to the new program position.  
The washing water in the tub not be emptied  
out. Start the new program by depressing the  
“Start/Pause” button again.  
If the machine is already heating or the water  
level is above the bottom edge of the door or  
that the drum is turning. In this case the door  
can not be opened.  
Interrupting a program  
If you can not open the door but you need to  
open it you have to switch the machine off by  
turning the selector dial to “Off”. After about 3  
minutes the door can be opened (pay attention  
to the water level and temperature!).  
Depress the “Start/Pause” button to interrupt a  
program which is running, the corresponding  
light starts to flash. Depress the button again to  
restart the program.  
International wash code symbols  
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.  
Energetic wash  
Max.wash  
temperature  
95 °C  
Max.wash  
temperature  
60 °C  
Max.wash  
temperature  
40 °C  
Max.wash  
temperature  
30 °C  
Hand wash  
Do not wash  
at all  
Delicate wash  
Bleaching  
Ironing  
Bleach in cold water  
Do not bleach  
Hot iron max 200°C  
Warm iron max 150°C  
Lukewarm iron max 110°C  
Do not iron  
Dry cleaning  
Dry cleaning  
in all solvents  
Dry cleaning in perchlorethylene,  
petrol, pure alcohol, R 111 & R 113  
Dry cleaning in petrol,  
pure alcohol and R 113  
Do not  
dry clean  
high  
temperature  
low  
temperature  
Tumble dry  
Do not  
tumble dry  
Drying  
16  
 
Programs informations  
To reset a programme and to switch off the machine turn the selector dial  
to “Off”. Now, a new programme can be selected.  
(Cancelling/Off)  
Washing programme for white and coloured cottons fabrics.  
Cottons  
Cottons  
Prewash  
select this program if you wish your laundry to be prewashed at 30° C  
before the main wash.  
select this program if you wish your laundry to be washed is slightly/  
normally soiled cottons. This program will obtain good washing results  
whilst saving energy.  
Cottons  
Economy  
Synthetics  
Washing programme for synthetic or mixed fabrics.  
Highly energy efficient cold wash programme for lightly soiled laundry.  
This programme requires a detergent which is active in cold water.  
Mixed Fabric  
Washing programme for delicate fabrics.  
Delicates  
Washing programme for machine washable wool as well as for hand  
washable woollens and delicate fabrics with the “hand washing  
symbol.  
Handwash/  
Wool  
” care  
With this programme it is possible to rinse and spin cotton garments which  
have been washed by hand. The machine performs 3 rinses, followed by a  
final spin at maximum speed. The spin speed can be reduced by pressing  
Spin button.  
Rinse  
Drain  
Spin  
For emptying out the water of the last rinse in programmes with the  
“Rinse Hold” option. Turn first the programme selector dial to “Off”, then  
select programme Drain and press the Start/Pause button.  
Separate spin for hand washed garments and after programmes with  
“Rinse Hold” option. Before selecting this programme the selector dial  
must be turned to “Off”. You can choose the speed by means of the  
relevant button to adapt it to the fabrics to be spun.  
Selecting this programme the laundry is gently washed and spun to avoid  
any creasing. In this way ironing is easier. Furthermore the machine will  
perform some additional rinses. This programme can be used only for  
cotton and synthetic fabrics.  
Easy Iron  
Blanket  
Mini 30  
Jeans  
A gentle program designed for mixed fabrics found in delicate clothes.  
Separate programme for lightly soiled synthetics, mixed fabrics and  
delicates.  
Trousers, shirts or jackets in denim and jersey realized with hi-tech  
materials. The Extra Rinse option is activated automatically.  
17  
 
Washing programs  
Type of laundry  
Max.  
Load  
Program/  
Temperature  
Description  
of program  
Options  
- Spin Reduction  
- Rinse Hold  
- Delay Start  
- Super Quick  
- Extra Rinse  
7.0  
kg  
White, coloured cotton  
and linen (Normally  
soiled items).: e.g. shirts, Rinses  
Main wash at  
Cold - 90° C  
Cottons  
Cold - 90° C  
underwear, towels.  
Long spin  
- Spin Reduction  
- Rinse Hold  
- Delay Start  
- Super Quick  
- Extra Rinse  
White, coloured cotton  
and linen (Heavy soiled  
items).: e.g. sheets,  
tablecloths, household  
linen.  
Main wash at  
Cold - 90° C  
Rinses  
7.0  
kg  
Prewash  
Cold - 90° C  
Long spin  
Main wash at  
40° - 60° C  
Rinses  
White, coloured cotton  
and linen (slightly or  
normally soiled cotton  
items).: e.g. shirts,  
blouses, underwear,  
towels.  
7.0  
kg  
- Spin Reduction  
- Rinse Hold  
- Delay Start  
- Extra Rinse  
Economy  
40° - 60° C  
Long spin  
2.5  
kg  
- Spin Reduction  
- Rinse Hold  
- Delay Start  
- Super Quick  
- Extra Rinse  
Synthetic or mixed fabrics Main wash at  
(Normally soiled items).: Cold - 60° C  
e.g. underwear, coloured Rinses  
Synthetics  
Cold - 60° C  
garments, non-shrink  
shirts, blouses.  
Long spin  
2.5  
kg  
Mixed fabrics (lightly  
soiled laundry).  
Main wash at  
Cold  
Rinses  
- Spin Reduction  
- Rinse Hold  
- Delay Start  
- Extra Rinse  
Mixed Fabric  
Cold  
Long spin  
Main wash at - Spin Reduction  
2.5  
kg  
Delicate fabrics  
Delicates  
(Maximum 700 rpm)  
- Rinse Hold  
- Delay Start  
Cold - 40° C  
Rinses  
Short spin  
(Normally soiled items).:  
e.g. curtains, acrylics,  
viscose, polyester.  
Cold - 40° C  
- Super Quick  
- Extra Rinse  
Woollens and hand  
washing fabrics.  
Main wash at - Spin Reduction  
2.0  
kg  
Handwash/  
Wool  
- Rinse Hold  
- Delay Start  
Cold - 40° C  
Rinses  
Cold - 40° C  
Long spin  
- Spin Reduction  
- Rinse Hold  
- Delay Start  
- Extra Rinse  
Separate rinse cycle for  
hand washed items of  
cottons.  
7.0  
kg  
Rinses  
Long spin  
Rinse  
18  
 
Type of laundry  
Max.  
Load  
Program/  
Temperature  
Description  
of program  
Options  
For emptying out the  
water left in the drum.  
Drain of  
water  
Not available  
7.0  
kg  
Drain  
Spin  
- Spin Reduction  
- Delay Start  
7.0  
kg  
Separate spin program  
for spin out the water  
from clothes.  
Drain  
Long spin  
2.5  
kg  
- Spin Reduction  
(Maximum 900 rpm)  
- Rinse Hold  
Main wash at  
Cold - 40° C  
Rinses  
Easy Iron  
Cottons and synthetic  
or mixed fabrics.  
Cold - 40° C  
- Delay Start  
Short spin  
- Extra Rinse  
- Spin Reduction  
(Maximum 700 rpm)  
- Delay Start  
Main wash at  
30° - 40° C  
Rinses  
A gentle program  
designed for mixed  
fabrics found in delicate  
clothes.  
7.0  
kg  
Blanket  
30° - 40° C  
Short spin  
Main wash at  
30° C  
Rinses  
Synthetics and delicates  
(lightly soiled items) or  
which only needs  
- Spin Reduction  
(Maximum 700 rpm)  
- Delay Start  
2.5  
kg  
Mini 30  
30° C  
Short spin  
freshening up.  
2.5  
kg  
- Spin Reduction  
- Rinse Hold  
- Delay Start  
Trousers, shirts or  
jackets in denim and  
jersey realized with  
hi-tech materials.  
Main wash at  
Cold - 60° C  
Rinses  
Jeans  
Cold - 60° C  
Long spin  
* Cottons Economy at 60 °C is recommended for a full load of normally soiled cottons, and is  
the water and energy rating label program (in accordance with CEE 92/75 standards).  
Care and cleaning  
Important!  
After each wash  
You must DISCONNECT the appliance from the  
electricity supply, before you can carry out any  
cleaning or maintenance work.  
Leave the door open for a while. This helps to  
prevent mould and stagnant smells forming  
inside the appliance. Keeping the door open  
after a wash will also help to preserve the door  
seal.  
Descaling  
The water we use normally contains lime. It is a  
good idea to periodically use a water softening  
powder in the machine. Do this separately from  
any laundry washing, and according to the  
softening powder manufacturer's instructions.  
This will help to prevent the formation of lime  
deposits.  
Maintenance Wash  
With the use of low temperature washes it is  
possible to get a build up of residues inside  
the drum. We recommend that a maintenance  
wash be performed on a regular basis.  
19  
 
use a small brush  
to clean the recess.  
To run a maintenance wash:  
The drum should be empty of laundry.  
Select the hottest cotton wash program.  
Use a normal measure of detergent, must be  
a powder with biological properties.  
External cleaning  
Replace the drawer and run the rinse programme  
without any clothes in the drum.  
Clean the exterior cabinet of the appliance with  
soap and water only, and then dry thoroughly.  
Cleaning the dispenser drawer  
Cleaning the drain filter  
The washing powder and additive dispenser  
drawer should be cleaned regularly.  
Drain filter collects lint and other items left in the  
dirty laundry to prevent pump blockage  
Remove the drawer  
by pressing the  
catch downwards  
and by pulling it out.  
The pump must be cleaned regularly. To clean  
the filter, proceed as follows:  
Turn programme selector dial to position Off  
(Off).  
Unplug the appliance.  
Open the door.  
Turn the drum and align the filter cover  
(FILTER) with the arrow on the door seal.  
Flush it out under a tap, to remove any traces  
of accumulated powder.  
To aid cleaning,  
the top part of  
the additive  
compartment  
should be  
removed.  
Open the filter cover by pressing the special  
hook and by rotating the cover upwards.  
Cleaning the drawer recess  
Having removed the drawer, use a small brush  
to clean the recess, ensuring that all washing  
powder residue is removed from the upper and  
lower part of the recess.  
Press here  
20  
 
Hold filter securly  
and pull upwards to  
remove it from its  
position.  
close the filter  
cover.  
insert the mains  
plug again.  
Remove eliminate the  
eventual fluff or small  
objects around the  
filter.  
Important!  
Do not start washing clothes without the  
filter in its place.  
Clean the filter under  
the water tap.  
Cleaning the water inlet filter  
If your water is very hard or contains traces of  
lime deposit, the water inlet filter may become  
clogged.  
After cleaning the  
filter, open the filter  
cover and insert the  
filter back to its  
position.  
It is therefore a good idea to clean it from time  
to time.  
Turn off the water  
tap.  
Unscrew the water  
inlet hose.  
Clean the filter  
using a hard bristle  
brush.  
Important!  
Tighten up the inlet  
hose.  
The filter is inserted correctly when the  
indicator on this top is visible and you  
will hear “Click” sound.  
21  
 
Something not working  
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily  
without calling out an engineer. Before contacting your local Service Centre, please carry out the  
checks listed below.  
During machine operation it is possible that the red Start/Pause pilot light flashes to indicate that  
the machine is not working.  
Once the problem has been eliminated, press the Start/Pause button to restart the program. If  
after all checks, the problem persists, contact your local Service Centre.  
Malfunction  
Possible cause  
Solution  
The door has not been closed.  
Close firmly the door.  
(Red Start/Pause pilot light flashes)  
The plug is not properly inserted in  
the power socket.  
Insert the plug into the power  
socket.  
There is no power at the socket.  
Please check your domestic  
electrical installation.  
The washing  
machine does  
not start:  
The selector dial is not correctly  
positioned and the Start/Pause  
button has not been depressed.  
Please turn the selector dial and  
press the Start/Pause button  
again.  
The delay start has been selected.  
If the laundry are to be washed  
immediately, cancel the delay  
start.  
The water tap is closed.  
Open the water tap.  
(Red Start/Pause pilot light flashes)  
The inlet hose is squashed or kinked. Check the inlet hose connection.  
(Red Start/Pause pilot light flashes)  
The machine  
does not fill:  
The filter in the inlet hose is blocked. Clean the water inlet hose filter.  
(Red Start/Pause pilot light flashes)  
The door is not properly closed.  
Close firmly the door.  
(Red Start/Pause pilot light flashes)  
The machine fills  
then empties  
immediately:  
The end of the drain hose is too low. Refer to relevant paragraph in  
“water drainage” section.  
The drain hose is squashed or kinked. Check the drain hose connection.  
(Red Start/Pause pilot light flashes)  
The drain filter is clogged.  
(Red Start/Pause pilot light flashes)  
Clean the drain filter.  
The machine  
does not empty  
and/or does not  
spin:  
The option Rinse Hold has been  
selected.  
Disable the option Rinse Hold or  
select Spin program.  
The laundry is not evenly distributed  
in the drum.  
Redistribute the laundry.  
22  
 
Malfunction  
Possible cause  
Solution  
Too much detergent or unsuitable  
detergent (creates too much foam)  
has been used.  
Reduce the detergent quantity or  
use another one.  
Check whether there are any leaks  
Check the water inlet hose  
from one of the inlet hose fittings. It is connection.  
not always easy to see this as the  
water runs down the hose; check to  
see if it is damp.  
There is water on  
the floor:  
The drain hose is damaged.  
Change it with a new one.  
Too little detergent or unsuitable  
detergent has been used.  
Increase the detergent quantity or  
use another one.  
Stubborn stains have not been  
treated prior to washing.  
Use commercial products to treat  
the stubborn stains.  
Unsatisfactory  
washing results:  
The correct temperature was not  
selected.  
Check if you have selected the  
correct temperature.  
Excessive laundry load.  
Introduce into the drum less  
laundry.  
The program is still running.  
Wait the end of washing cycle.  
The door will not  
open:  
The door lock has not been released. Wait about 3 minutes.  
There is water in the drum.  
Select drain or spin program to  
empty out the water.  
The transit bolts and packing have  
not been removed.  
Check the correct installation of  
the appliance.  
The support feet have not been  
adjusted.  
Check the correct levelling of the  
appliance.  
The machine  
vibrates or is  
noisy:  
The laundry is not evenly distributed  
in the drum.  
Redistribute the laundry.  
Maybe there is very little laundry in the Load more laundry.  
drum.  
Unstable floors eg. wooden floors.  
The machine is fitted with a type of  
motor which makes an unusual noise  
compared with other traditional  
motors. This new motor ensures a  
softer start and more even distribution  
of the laundry in the drum when  
spinning, as well as increased stability  
of the machine.  
The machine  
makes an unusual  
noise:  
23  
 
Malfunction  
Possible cause  
Solution  
The electronic unbalance detection  
device has cut in because the  
Redistribute the laundry.  
laundry is not evenly distributed in  
the drum. The laundry is redistributed  
by reverse rotation of the drum. This  
may happen several times before the  
unbalance disappears and normal  
spinning can resume. If, after 10  
minutes, the laundry is still not evenly  
distributed in the drum, the machine  
will not spin. In this case, redistribute  
the load manually and select the spin  
programme.  
Spinning starts  
late or the  
machine does not  
spin:  
Machines based on modern  
technology operate very  
economically using very little water  
without affecting performance.  
No water is visible  
in the drum:  
If you are unable to identify or solve the problem, contact our service centre. Before  
telephoning, make a note of the model, serial number and purchase date of your machine,  
the Service Centre will require this information.  
Model description (MOD.).......................  
Product number (PNC) ...........................  
Serial number (S.N.) ...............................  
24  
 

Weed Eater Trimmer 545137264 User Manual
Weider Home Gym WEBE08900 User Manual
Westinghouse Flat Panel Television CW40T6DW User Manual
White Westinghouse Washer SWS1233CQ S0 User Manual
Winegard TV Antenna RP80RTS User Manual
Woodstock Saw W1761 User Manual
Xerox Printer Accessories SquareFold Trimmer User Manual
Xerox Printer Phaser 2135 User Manual
Yamaha Electronic Keyboard Digital Grand Piano User Manual
Zhone Technologies Network Card 6412 A1 xxx User Manual