Zanussi Refrigerator ZBB6286 User Manual

REFRIGERATOR-  
FREEZER  
ZBB 6286  
INSTRUCTION BOOKLET  
2223 460-12  
 
Disposal of old Appliances  
At the end of the Appliance  
Life  
The symbol  
on the product or on its packaging  
indicates that this product may not be treated as  
household waste. Instead it shall be handed over to  
the applicable collection point for the recycling of  
electrical and electronic equipment. By ensuring this  
product is disposed of correctly, you will help prevent  
potential negative consequences for the environment  
and human health, which could otherwise be caused  
by inappropriate waste handling of this product. For  
more detailed information about recycling of this  
product, please contact your local city office, your  
household waste disposal service or the shop where  
you purchased the product.  
When disposing of your appliance, use an  
authorised disposal site.  
Remove the plug and ensure that any locks or  
catches are removed, to prevent young children  
being trapped inside.  
CONTENTS  
Instructions for the User  
Important Safety Information  
Instructions for the  
Installer  
2
4
4
4
4
4
5
5
5
5
5
6
6
6
7
7
7
Operation  
Before using  
13  
Technical Specification  
14  
14  
14  
Installation  
Positioning  
Control panel - Use of the freezer  
Start your appliance  
Temperature control  
Quick-freezing  
Shelf holders  
15  
Electrical Connection  
Instruction for totally built-in  
appliances - Door Reversal  
Recess dimensions  
Freezing fresh food  
Frozen food storage  
Thawing  
16  
16  
17  
18  
Installing the Applince into it’s Housing  
Attaching the Furniture Door  
Making ice cubes  
Use of the refrigerator-Setting the temperature  
Fresh food refrigeration  
Normal operating sounds  
Movable shelves  
Positioning the door shelves  
Freezing calendar  
8
Hints and Tips  
9
9
9
9
9
9
Maintenance and Cleaning  
Internal cleaning  
External cleaning  
When the appliance is not in use  
Changing the light bulb  
Defrosting  
10  
11  
11  
12  
Something Not Working  
Service and Spare Parts  
Customer Care  
Guarantee Conditions  
3
 
OPERATION  
Before using  
Remove all securing tapes. Wash inside the  
appliance with lukewarm water and bicarbonate of  
soda (5 ml to 0.5 litre of water).  
Do not use soap or detergent as the smell may  
linger. Dry thoroughly.  
Control panel  
A
B
C
D
A -  
B -  
C -  
D -  
Pilot light - Green  
Thermostat control knob  
Fast freeze light - Yellow  
Fast freeze switch  
Control Panel - Use of the freezer  
A. Pilot light  
Temperature control  
The temperature within the freezer is controlled by  
the thermostat situated in the middle of the  
appliance.  
The operation light is illuminated continuously, to  
show that the appliance is on.  
To operate the freezer proceed as follows:  
B.Thermostat control knob  
Position = minimum coldness  
G
Turn the thermostat control knob clockwise to  
required setting.  
Position G = maximum coldness  
Turn the thermostat control knob beyond the «O»  
position.  
C. Fast freeze light  
The fast freeze light is illuminated, to show that the  
fast freeze function is working.  
When you first start the fridge freezer, we suggest  
that you turn the thermostat control to a medium  
setting. For easier turning of this control, use a small  
coin.The internal temperature of the fridge freezer is  
automatically adjusted by the thermostat to ensure  
safe food storage.  
D. Fast freeze control switch  
When you place fresh food in the appliance, press  
the fast freeze control switch.  
Start your appliance  
Allow the appliance to stand for 2 hours after  
installation.  
Insert the plug into the wall socket. The pilot light (A)  
will illuminate to show that the appliance is on.  
Turn the thermostat control (B) to a midway setting.  
Leave the appliance for approximately 4 hours for  
the correct temperature to be reached before placing  
food inside.  
To switch off the appliance turn the thermostat  
control to position “O” .  
4
 
Fast-freezing  
For fast-freezing, push the fast freeze switch (D). The  
super control light (C) will then light up.  
Important  
In the event of a power cut the food in the freezer will  
not be affected if the power cut is short and if the  
freezer is full. Do not open the door. Should the food  
begin to thaw, it must be consumed quickly and must  
not be re-frozen .  
The Fast-freezing function accelerates the freezing  
of fresh food and, at the same time, protects  
foodstuffs already stored from undesirable warming.  
If this function is not ended manually, the appliance  
switches off the Fast-freezing function after 52 hours.  
The yellow light goes out.  
This function can be ended manually at any time by  
pressing the fast freeze switch again. The yellow light  
goes out.  
Thawing  
Frozen food, prior to being used, can be thawed in  
the fridge or at room temperature depending on the  
time available. Small food items may even be cooked  
from frozen; in this case cooking will take longer.  
Freezing fresh food  
Any frozen food which is allowed to thaw accidentally  
should either be eaten as soon as possible or thrown  
away. Alternatively, if the food is uncooked and has  
not been completely defrosted it can be cooked and  
then refrozen.  
The 4-star compartment is suitable for long term  
storage of commercially frozen food and for freezing  
fresh food.  
To freeze fresh foods it is not necessary to move the  
thermostat knob from the normal setting. Push the  
fast freeze switch at least 3 hours before loading  
food.  
Meat, fish and fruit should be thawed in the  
refrigerator compartment and small pieces of meat  
can even be cooked while still frozen, but you must  
ensure that it is thoroughly cooked through.  
In any 24 hours you can freeze up to 4 kg. of fresh  
food.  
Vegetables should be directly immersed in boiling  
water; ready-cooked dishes can be placed directly in  
the oven in their aluminium wrapping.  
Place the food to be frozen in the lower of the freezer  
compartment as this is the coldest part.  
To guarantee a good operation of the appliance  
during normal use, the drawers should not be  
removed.  
A microwave oven is particularly suitable for thawing  
any type of frozen or deep-frozen food: follow the  
oven instructions, particularly regarding the  
placement of aluminium wrapping or containers in  
the oven.  
Frozen food storage  
When first starting-up or after a period out of use,  
before putting the products in the compartment let  
the appliance run for at least two hours on the  
coldest setting, then turn the thermostat knob to the  
normal operating position.  
Defrosted cooked food must never be refrozen.  
Making ice cubes  
The appliance is provided with one or more trays for  
ice-cubes trays.  
Do not exceed the storage period indicated by the  
manufacturer.  
Fill the tray(s) 3/4 full to give the ice space to expand  
and place them in the freezer compartment.  
Finally, do not open the door frequently or leave it  
open longer than is absolutely necessary.  
To release the ice cubes simply give the tray a slight  
twist.  
Do not use sharp or metallic instruments to remove  
the trays from the freezer.  
Warning  
Do not put carbonated liquids, (fizzy drinks etc.), in  
the freezer compartment.  
Ice lollies, if consumed immediately after removal  
from the freezer, can cause low temperature skin  
burns.  
Do not remove items from the freezer if your hands  
are damp/wet, as this could cause skin abrasions or  
“frost/freezer burns”.  
5
 
Use of the refrigerator  
Normal Operating Sounds  
The thermostat regulates for both freezer and  
refrigerator compartments.  
You may hear faint gurgling or bubbling sounds  
when the refrigerant is pumped through the coils  
or tubing at the rear, to the cooling  
Setting the temperature  
plate/evaporator or to the fixed freezer shelves.  
Position = minimum coldness  
G
When the compressor is on, the refrigerant is  
being pumped round, and you will hear a whirring  
sound or pulsating noise from the compressor.  
Position G = maximum coldness  
Turn the thermostat dial to the required position.  
A thermostat controls the compressor, and you  
will hear a faint ’click’ when the thermostat cuts in  
and out.  
Insert a coin to turn the thermostat dial to the  
required position.  
The thermostat setting can vary as the temperature  
inside the refrigeration compartment depends on the  
following factors:  
room temperature  
how often the door is opened  
how much food is stored  
position of the appliance  
Fresh food refrigeration  
To obtain the best performance, do not store warm  
food or evaporating liquids in the refrigerator; do  
cover or wrap the food, particularly if it has a strong  
flavour.  
Do not cover the shelves with any protective  
material, such as paper, cardboard or plastic, which  
may obstruct the air circulation through them.  
To help you use your refrigerator correctly, here are  
some more useful hints:  
Raw meat (beef, pork, lamb & wild fowl): wrap in  
polythene bags and place on top of the salad  
crispers.  
Meat can only be stored safely in this way for  
one or two days at the most.  
Fruit & vegetables: these should be thoroughly  
cleaned and placed in the bottom salad crispers.  
Butter & cheese: these should be placed in special  
airtight containers or wrapped in aluminium foil or  
polythene bags to exclude as much air as possible.  
Milk bottles: these should have a cap and should be  
stored in the bottle rack on the door.  
6
 
Movable shelves  
The walls of the refrigerator have runners so that the  
shelves can be positioned as desired .  
For better use of space, the front half-shelves can lie  
over the rear ones.  
D338  
Positioning the door shelves  
To permit storage of food packages of various sizes,  
the door shelves can be adjusted in height. To do this  
proceed as shown in the diagram.  
The top shelf can be removed for easier cleaning.  
Freezing Calendar  
The symbols show different types of frozen goods.  
The numbers indicate storage times in months for the appropriate types of frozen goods.Whether the upper or lower  
value of the indicated storage time is valid depends on the quality of the foods and pre-treating before freezing.  
7
 
HINTS AND TIPS  
Food Storage  
In the Event of a Power Failure  
To obtain the best results from your appliance,  
neither hot foods nor liquids which may  
evaporate, should be placed in the larder  
compartment.  
If there is a power failure during the storage of frozen  
foods, keep the door closed. If the temperature within  
your freezer should rise do not refreeze the food  
without checking it’s condition.  
Keep the time between buying chilled food and  
placing it in your fridge as short as possible.  
The following guidelines should assist you.  
Do not push food together too much, try to allow  
air to circulate around each item.  
Ice Cream:  
Once thawed should be discarded.  
Fruit and Vegetables:  
Do not store food uncovered.  
Remove suspect food from your refrigerator and  
clean, refer to ‘Maintenance and Cleaning’.  
If soft should be cooked and used up.  
Bread and Cakes:  
Ensure that food placed in the freezer is dated  
and labelled and used in date order to ensure  
that food is consumed at its best.  
Can be refrozen without danger.  
Shellfish:  
Avoid buying frozen food if you cannot store it  
straight away. The use of an insulated container is  
advisable. When you arrive home place the frozen  
food in the freezer immediately.  
Should be refrigerated and used up quickly.  
Cooked Dishes:  
i.e. casseroles, should be refrigerated and used up.  
Large Pieces of Meat:  
Can be re-frozen providing there are ice crystals  
remaining within them.  
Energy Saving Advice  
Do not install the cabinet close to sources of  
heat, i.e. boiler or radiator.  
Small Joints:  
Should be cooked and then re-frozen as cooked  
dishes.  
Locate the appliance in a cool well ventilated  
room and make sure that the air openings of the  
cabinet are not obstructed.  
Chicken:  
Avoid unnecessary frosting in the cabinet by  
packing all foodstuffs into airtight packages  
before placing them in the freezer.  
Should be cooked and re-frozen as a fresh dish.  
Always leave warm food to cool down to room  
temperature before placing in the fridge or  
freezer.  
Food which is to be frozen (when cool) should be  
placed in the fridge before being transferred to  
the freezer.  
Thaw frozen food in the fridge. This will ensure  
safer defrosting of foods and reduce the work of  
the refrigeration unit.  
Try to avoid keeping the door open for long  
periods, or opening the door too frequently as  
warm air will enter the cabinet, and cause the  
compressor to switch on unnecessarily often.  
Ensure there are no obstructions preventing the  
door from closing properly.  
8
 
MAINTENANCE AND CLEANING  
Before any maintenance or cleaning work is carried  
out, DISCONNECT the appliance from the  
ELECTRICITY supply.  
Internal cleaning  
Clean the inside and accessories with warm water  
and bicarbonate of soda (5ml to 0.5 litre of water).  
Rinse and dry thoroughly.  
NEVER USE DETERGENTS, ABRASIVE  
POWDERS, HIGHLY PERFUMED  
CLEANING PRODUCTS OR WAX  
POLISHES,TO CLEAN THE INTERIOR AS  
THESE WILL DAMAGE THE SURFACE AND  
LEAVE A STRONG ODOUR.  
press on the rear hook and at the same time slide the  
cover in the direction indicated by the arrow.  
Unscrew the bulb and replace it with one of the same  
power (the maximum power is shown on the light  
diffuser) available from your nearest Service Force  
Centre.  
Replace the light cover by sliding it into its original  
position.  
When the appliance is not in use  
When the appliance is not in use for long periods,  
disconnect from the electricity supply, empty all  
foods and clean the appliance, leaving the doors ajar  
to prevent unpleasant smells.  
Defrosting  
Refrigerator  
The refrigerator automatically defrosts every time the  
compressor stops. The water is discharged, via the  
pipe, into a tray located at the back of the appliance  
above the compressor, where it evaporates.  
External cleaning  
Once or twice a year dust the condenser (black grill)  
and the compressor at the back of the appliance,  
with a brush or vacuum cleaner, see figure, as an  
accumulation of dust will affect the performance of  
the appliance and cause excessive electricity  
consumption.  
D037  
Important  
To avoid defrost water overflowing into the fridge,  
periodically clean the water discharge hole in the  
centre of the V shaped drip collector at the back of  
the refrigerator compartment behind the fruit and  
vegetable drawer. Use the defrost cleaner provided  
which you will find already inserted into the  
discharge hole.  
PR259  
Changing the light bulb  
Should the interior light fail to work, first switch off  
the appliance and disconnect from the electricity  
supply, then replace the bulb as follows;  
Remember to wash the defrost cleaner in hot soapy  
water at regular intervals. Dry throughly before  
replacing.  
Freezer  
Your appliance is frost free, which means there is no  
need to manually defrost your appliance as this will  
be carried out automatically.  
9
 
SOMETHING NOT WORKING  
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or  
installation a charge will be made, even if the appliance is under guarantee.  
Before contacting your local Service Force Centre, check the following points:  
Symptom  
Solution  
No power to the appliance  
Check there is power at the socket.  
Check there is not a power cut by checking the  
household lights.  
Check the fuse has not blown.  
The light does not come on  
Ensure that the bulb is correctly fitted.  
Replace the bulb if it has blown.  
Check the door light switch is not jammed.  
The temperature in the fridge or freezer section is  
too high  
Check the thermostat control knob mounted in the  
cross piece between the fridge and freezer is turned  
to the correct setting relative to ambient conditions.  
Check the ambient temperature is within the  
appliance’s operating limits, please refer to the  
installation section in this instruction book.  
Relocate the appliance if necessary.  
The freezer door will not open  
Has door just been opened? If so leave for a few  
minutes to allow the air pressure to equalise.  
The compressor runs continously  
Adjust the thermostat control knob to give correct  
temperature control. See “Setting the temperature”.  
Check that the doors are closed.  
Large quantities of food have recently been placed in  
the cabinet and/or door is frequently opened.  
Check that air ventilation is not obstructed.  
Ensure the doors are not left open.  
Excessive frost and ice has built up  
Check that nothing is preventing the doors from  
closing.  
Is the door gasket intact and clean.  
Noise  
Refer to normal operating sounds.  
Water under the salad bin  
Check the drain hole is not blocked. (see  
Maintenance and Cleaning).  
10  
 
SERVICE AND SPARE PARTS  
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local  
Zanussi Service Force Centre by telephoning:-  
0870 5 929929  
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.  
For the address of your local Service Force Centre and further information about Service Force, please visit the  
For Customer Service in the Republic of Ireland please  
contact us at the address below:  
Zanussi  
Electrolux Group (Ire) Ltd  
Long Mile Road  
Dublin 12  
Republic of Ireland  
Telephone : +353 (0)1 4090751  
Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not  
Working?  
When you contact the Service Force Centre you will need to give the following details:  
1.  
2.  
3.  
4.  
5.  
Your name, address and post code  
Your telephone number  
Clear and concise details of the fault  
The model and serial number of the appliance (found on the rating plate)  
The purchase date  
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee  
service calls.  
CUSTOMER CARE DEPARTMENT  
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products,  
please contact our Customer Care Department by letter or telephone at the address below or visit our website  
Customer Care Department  
Major Appliances  
Zanussi  
Addington Way  
Luton  
Bedfordshire  
LU4 9QQ  
Tel: 08705 727 727 ( * )  
* calls to this number may be recorded for training purposes.  
11  
 
GUARANTEE CONDITIONS  
Standard guarantee conditions  
We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part  
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair  
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:  
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.  
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s  
instructions.  
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not  
authorised by us.  
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or  
defective part replaced shall become the Company’s property.  
This guarantee is in addition to your statutory and other legal rights.  
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these  
hours in which case a premium will be charged.  
Exclusions  
This guarantee does not cover:  
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or  
removable parts of glass or plastic.  
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the  
European Community (EC) or European Free Trade Area.  
Appliances found to be in use within a commercial environment, plus those which are subject to rental  
agreements.  
Products of Zanussi manufacture which are not marketed by Zanussi.  
European Guarantee  
If you should move to another country within Europe then your guarantee moves with you to your new home  
subject to the following qualifications:  
The guarantee starts from the date you first purchased your product.  
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of  
use for this brand or range of products.  
This guarantee relates to you and cannot be transferred to another user.  
Your new home is within the European Community (EC) or European Free Trade Area.  
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a  
normal household.  
The product is installed taking into account regulations in your new country.  
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your  
new home. They will then ensure that the local Service Organisation is aware of your move and able to look  
after you and your appliances.  
France  
Germany  
Italy  
Senlis  
+33 (0)3 44 62 29 29  
+49 (0)800 234 7378  
+39 (0)0434 39 4700  
+46 (0)8 672 53 90  
+ 44 ( 0) 8705 727727  
Nürnberg  
Pordenone  
Stockholm  
Luton  
Sweden  
UK  
12  
 
TECHNICAL SPECIFICATIONS  
POWER SUPPLY VOLTAGE AND FREQUENCY  
TOTAL POWER ABSORBED  
230-240 V / 50 Hz  
160 W  
AVERAGE DAILY UNITS ELECTRICITY *  
GROSS CAPACITY  
0.86 kWh  
Fridge  
214 l  
68 l  
Freezer  
NET CAPACITY  
Fridge  
210 l  
55 l  
Freezer  
STAR RATING  
* This figure is based on standard test results in accordance with European Standard EN 153.  
Actual consumption will depend on how the appliance is used and where it is located.  
13  
 
INSTALLATION  
Important  
Warning  
IF YOU ARE DISCARDING AN OLD APPLIANCE  
THAT HAS A LOCK OR CATCH ON THE DOOR,  
YOU MUST ENSURE THAT IT IS MADE  
UNUSABLE TO PREVENT YOUNG CHILDREN  
BEING TRAPPED INSIDE.  
It must be possible to disconnect the appliance from  
the mains power supply; the plug must therefore be  
easily accessible after installation.  
Depending upon the position which you choose for  
your appliance, you may wish to reverse the way in  
which the door opens. To do this, refer to instructions  
on “Door reversal directions”.  
Positioning  
This appliance should only be installed at a location  
where the ambient temperature corresponds to the  
climate classification indicated on the rating plate,  
which is located at the left on the inside of the  
appliance.  
The following table shows which ambient  
temperature is correct for each climate classification:  
SN +10°C to + 32°C  
N
+16°C to + 32°C  
ST +18°C to + 38°C  
+18°C to + 43°C  
T
The appliance should be located in a dry  
atmosphere, out of direct sunlight and away from  
continuous heat and extreme temperature, e.g. not  
next to a boiler or radiator, or in a very cold room e.g.  
an outhouse. If these temperatures are exceeded i.e.  
warmer or colder, then the appliance may not  
operate correctly.  
For building-in and door reversal instructions please  
refer to the relevant instructions on the following  
pages.  
Shelf holders  
Your appliance is equipped with shelf retainers that  
make it possible to secure the shelves during  
transportation.  
A
To remove them proceed as follows:  
Raise the shelf from the back, push it in the direction  
of the arrow until it is freed and remove the retainers.  
B
14  
 
For replacement, use a 13amp BSI362 fuse. Only  
ASTA or BSI approved fuses should be used.  
Electrical connections  
The plug must not be used if the fuse cover/carrier is  
lost. The cover/carrier is indicated by the coloured  
insert at the base of the plug.  
Any electrical work required to install this appliance  
should be carried out by a qualified electrician or  
competent person.  
A replacement cover/carrier must be obtained from  
your local Zanussi Service Force Centre.  
WARNING:THIS APPLIANCE MUST BE  
EARTHED.  
This appliance complies with the E.E.C. Directive  
No. 87/308 of 2.6.87 relative to radio interference  
suppression.  
The manufacturer declines any liability should  
this safety measure not be observed.  
If the plug that is fitted to your appliance is not  
suitable for your socket outlet, it must be cut off and  
the appropriate plug fitted.  
This appliance complies with the following  
E.E.C. Directives:  
-
-
73/23 EEC of 19.2.73 (Low Voltage Directive)  
and subsequent modifications;  
Remove the fuse from the cut off plug.  
The cut off plug should then be disposed of to  
prevent the hazard of shocks in case it should be  
plugged into a 13amp socket in another part of your  
home.  
89/336 EEC of 3.5.89 (Electromagnetic  
Compatibility Directive) and subsequent  
modifications.  
Please ensure that when the appliance is  
installed it is easily accessible for the engineer in  
the event of a breakdown.  
Important  
The wires in the mains lead are coloured in  
accordance with the following code:  
Green andYellow  
Blue  
- Earth  
- Neutral  
- Live  
Brown  
If you fit your own plug, the colours of the wires in  
the mains lead of your appliance may not correspond  
with the markings identifying the terminals in your  
plug, proceed as follows:  
GREEN & YELLOW  
13 AMP. FUSE  
BROWN  
BLUE  
CORD CLAMP  
D207  
Connect the Green and Yellow (earth) wire to the  
terminal in the plug which is marked with the letter  
«E» or the earth symbol  
yellow.  
or coloured green and  
Connect the blue (neutral) wire to the terminal in the  
plug which is marked with the letter «N» or coloured  
black.  
Connect the brown (live) wire to the terminal in the  
plug which is marked with the letter «L» or coloured  
red.  
The plug moulded onto the lead incorporates a fuse.  
15  
 
Instructions for totally built-in  
appliances  
Door reversal  
The appliance is supplied with the right or  
left door opening.To change the opening  
direction of the door proceed as in the  
following instructions before installing it.  
1. Unscrew the upper pin and remove the spacer  
2. Remove the upper door and the upper hinge pin.  
C
B
A
3. Remove the hinge cover (A). Unscrew the pins  
(B) and spacers (C). Fit the hinge cover (A).  
4. Unscrew the lower pin and refit it on the opposite  
side.  
5. Refit the lower door.  
6. Refit the pins (B) and the spacers (C) on the  
middle hinge on the opposite side.  
7. Refit the upper door , the hinge pin and the  
spacer on the opposite side .  
min.  
50 mm  
Recess dimensions  
200 cm2  
Height (1)  
Depth (2)  
Width (3)  
1780 mm  
550 mm  
560 mm  
To ensure adequate ventilation, allow the clearances  
shown in figure.  
min.  
200 cm  
2
D567  
Furthermore, it is necessary that the cabinet has a  
ventilation recess with the following dimensions:  
depth  
width  
50 mm  
540 mm  
3
2
1
PR01  
16  
 
Make sure that a distance of 44 mm is maintained in  
the lower part between the kitchen furniture and the  
border of the appliance.  
1
The lower hinge cover inserted in the accessories  
bag, is useful to guarantee the exact position of the  
kitchen furniture and the appliance.  
44mm  
Also make sure that the appliance does not clamp  
the mains cable  
2
Fasten the appliance with 4 screws provided in the  
kit included with the appliance.  
(I = short) (P = long)  
I
P
Apply the sealing strip pushing it between the  
refrigerator and the adjacent cabinet.  
D724  
From the plastic cover (E), which is used to cover the  
hinge with the pivot pin, you must take away the part  
as indicated in the drawing.  
This operation is made easer since there is, in the  
internal part of the cover hinge lid a groove that  
facilates the removal of this coomponent.  
“Remove the part marked with DX, if the pivot pin is  
inserted in the right hinge, SX in opposite case.”  
Apply covers (C-D) on joint cover lugs and into hinge  
holes.  
Snap vent grille (B) and hinge covers (E) into  
position.  
C
D
E
E
B
17  
 
Separate parts Ha, Hb, Hc, Hd as shown in the  
figure.  
Hb  
Ha  
Hc  
Hd  
PR266  
Place guide (Ha) on the inside part of the furniture  
door, up and down as shown in the figure and mark  
the position of external holes. After having drilled  
holes, fix the guide with the screws supplied.  
ca. 50 mm  
90°  
90°  
ca. 50 mm  
Fix cover (Hc) on guide (Ha) until it clips into place  
Ha  
Hc  
8mm  
Open the appliance door and the furniture door at  
90°. Insert the small square (Hb) into guide (Ha).  
Put together the appliance door and the furniture  
door and mark the holes as indicated in the figure. .  
Ha  
Hb  
PR167  
Remove the brackets and mark a distance of 8 mm  
from the outer edge of the door where the nail must  
be fitted (K).  
8mm  
K
Ha  
18  
 
Place the small square on the guide again and fix it  
with the screws supplied.  
Should the lining up of the furniture door be  
necessary, use the clearance of slots.  
At the end of operations, it is necessary to check if  
the door of the furniture closes properly.  
Hb  
PR168  
Fix cover (Hd) on guide (Hb) until it clips into place.  
Hb  
Hd  
PR167/1  
If the appliance is fixed to the side of the kitchen unit,  
simply slacken the screws in fixing brackets (E),  
move the brackets as shown in the figure and re-  
tighten the screws.  
E
E
After completion of the door reversing operation,  
check that the door gasket adheres to the cabinet. If  
the ambient temperature is cold (i.e. in Winter), the  
gasket may not fit perfectly to the cabinet. In that  
case, wait for the natural fitting of the gasket or  
accelerate this process by heating up the part  
involved with a normal hairdryer on a low setting.  
19  
 
© Electrolux plc 2007  
 

West Bend Electric Grill 6111CF User Manual
Whirlpool Freezer EV150 User Manual
Whirlpool Oven W10392932A User Manual
Whirlpool Range ART660L User Manual
Whynter Beverage Dispenser WC 211DZ User Manual
Xantrex Technology Power Supply XPR 100 60 User Manual
Zanussi Refrigerator ZB3201 User Manual
Zanussi Ventilation Hood 640045 User Manual
Zebra Technologies Printer ZM400TM User Manual
Zenoah Welder GZ50N User Manual