Xerox Printer 127 B 114 User Manual

XEROX FreeFlow®  
Accxes® Firmware  
12.7 b 114  
Release Notes  
(For YKE, YKE-N,  
FRX, and LVX Controllers)  
December, 2007  
 
Table of Contents  
1 Introduction................................................................................................................... 3  
1.1 FEATURE KEYS: .....................................................................................................3  
1.1.1 Feature Key Descriptions................................................................................................. 3  
2 Release Deliverables.................................................................................................... 5  
2.1 Xerox 6030/6050 Wide Format Solution...................................................................5  
2.2 Xerox 8850, 510dp Print System..............................................................................5  
2.3 Xerox Print System 721p.......................................................................................... 5  
2.4 Xerox 6204 Wide Format Solution............................................................................5  
2.5 Xerox 6050A Wide Format Solution......................................................................... 5  
2.6 Xerox 8825/8830 Print System.................................................................................6  
3 Recommended Configurations................................................................................... 7  
4 Release Installation...................................................................................................... 8  
4.1 Accxes Client Tools ................................................................................................. 8  
4.2 WebPMT...................................................................................................................8  
4.3 Unix ..........................................................................................................................8  
5 New Features of 12.7.................................................................................................... 9  
5.1 IPv6 Support............................................................................................................. 9  
5.2 Folder Support for Copies on 6204 ......................................................................... 9  
5.3 PDF Transparency Flattening...................................................................................9  
5.4 Support for Camera JPEG files................................................................................ 9  
6 Release Notes............................................................................................................. 10  
6.1 Sets.........................................................................................................................10  
6.2 6204 Specific.......................................................................................................... 10  
6.2.1 Copying ARCH-E size prints.......................................................................................... 10  
6.2.2 Specifying titleblock for copies....................................................................................... 10  
6.3 6050/6030 Specific................................................................................................. 11  
6.3.1 Configuring the Remote printer...................................................................................... 11  
6.4 Controller................................................................................................................ 11  
6.4.1 Stamp does not appear.................................................................................................. 11  
6.4.2 Scaling interaction with “ANY”........................................................................................ 11  
6.4.3 Margins may cause image clipping................................................................................ 11  
6.4.4 CGM Files and folding................................................................................................... 11  
6.5 Wide Format Scanner.............................................................................................11  
6.5.1 Clear Last Image........................................................................................................... 12  
6.5.2 Invert Feature and Recall Last Job................................................................................ 12  
6.5.3 Scan-to-Print and Margins............................................................................................. 12  
6.5.4 Width Detection Sensors and Finishing......................................................................... 12  
6.5.5 Background Suppression............................................................................................... 12  
6.5.6 Scaling shaded documents............................................................................................ 12  
6.5.7 50000015 errors while copying...................................................................................... 12  
6.5.8 Recalling sets................................................................................................................ 12  
6.5.9 Washed out documents when scanning/copying........................................................... 13  
6.6 Manual Feed........................................................................................................... 13  
6.6.1 Manual feed media source will be ignored when used with the Accxes Client Tools’ page  
composition feature. .............................................................................................................. 13  
6.7 Instant Access........................................................................................................ 13  
6.7.1 InstantAccxes Folders not browse-able on IPv6 ........................................................... 13  
6.7.2 InstantAccxes Folders not accessible from MAC on IPv6 ............................................. 13  
6.8 Web Print Manager Tool (WebPMT)......................................................................13  
Page 1  
 
6.8.1 Printer Queue – Main WebPMT Screen......................................................................... 13  
6.8.2 German users only......................................................................................................... 14  
6.8.3 Large Scaling Factors.................................................................................................... 14  
6.8.4 HPGL Page – End of File............................................................................................... 14  
6.8.5 Display of Media Usage................................................................................................. 14  
6.8.6 Default PostScript Page Size......................................................................................... 14  
6.8.7 “Printer has been updated” message............................................................................. 14  
6.8.8 Disk Image Overwrite.................................................................................................... 15  
7 Customer Issues Resolved........................................................................................16  
7.1 The following customer issues were resolved in 12.7 b 114.................................. 16  
7.2 The following customer issues were resolved in 12.6 b 101.................................. 16  
7.3 The following customer issues were resolved in 12.5 b 120.................................. 17  
7.4 The following customer issues were resolved in 12.2 b 107.................................. 17  
7.5 The following customer issues were resolved in 12.2 b 102.................................. 18  
7.6 The following customer issues were resolved in 12.2 b 101.................................. 18  
7.7 The following customer issues were resolved in 12.1 b 110.................................. 19  
Page 2  
 
1 Introduction  
The FreeFlow® Accxes® Controller Firmware Release 12.7 b 114 provides multinational software  
for the Xerox 8825, 8830, 8850, 510dp, 721p, 6030, 6050, 6204, 6050A and for the Xerox Wide  
Format Scan System. The languages supported are English, Deutsch, Espanol, Francais,  
Italiano, Portugues, and Russian (Russian not supported on the printer UI for 8825, 8830, 8850,  
510dp, 6030, 6050, and 6050A).  
This document presents the following information about the FreeFlow® Accxes® Controller  
Release 12.7 build 114. The document applies to YKE, YKE-N, FRX, and LVX controllers and for  
simplicity they will simply be referred to as YKE.  
Release deliverables  
Recommended configurations  
Installation procedures  
Present supplemental information and known issues that are not mentioned in the published  
customer user documentation.  
New features  
1.1 FEATURE KEYS:  
1.1.1 Feature Key Descriptions  
Print and Copy Feature Keys are enabled on the YKE controller by loading the “OS Enablement”  
feature key.  
Additionally, the following functions will be unavailable until the appropriate feature key is  
loaded.  
DGN printing is enabled with an “Other CAD” feature key beginning in 12.5.  
JPEG 2000, PNG, BMP, and GIF printing is enabled with a Raster feature key beginning  
in 12.1.  
DWF printing is enabled with the “AutoCAD” feature key beginning in version 12.0.  
A 5D speed key has been introduced in 12.0 for the 6204.  
A 9D speed key has been introduced in 12.5 for the 6050A.  
Job Accounting Enables tracking media usage data for print, scan, and copy jobs.  
Account Management Tool, or some other external accounting tool, is used to assign  
User Id, Account Id, Printer Id associations, then collects and tallies the stored data from  
the printers).  
PostScript – Enables the interpretation of Adobe Postscript 3 and PDF 1.6 files.  
Disk Image Overwrite – Enables the security options for overwriting image data on the  
hard drive.  
Page 3  
 
Xerox 6030/6050 Wide Format Printer:  
Print Server Enablement – Enables print and copy mode for remote printer.  
Scan to Net to create an electronic file from a scanned image.  
Scan to Print to send the scan to net image to the printer.  
Xerox Wide Format Scanner Features:  
Color Enablement –Accxes - Allows color scanning when scan to net license is present.  
Speed Enhancement Turbo II – Accxes - Enables 4 ips scan speed for 36” wide.  
Speed Enhancement Turbo III – Accxes – Enables 7.33 ips Scans on YKE/YKE-N/FRX  
Controllers  
For more information on Feature Keys, see the Feature Key Instructions and Coupon Exchange  
Page 4  
 
2 Release Deliverables  
2.1 Xerox 6030/6050 Wide Format Solution  
The following executable is provided for the Xerox 6030/6050 Wide Format Solution and supports  
the Xerox Wide Format Scan System and GFI finisher.  
YKE/YKEN/FRX/LVX Controller:  
YKE_YKEN_FRX_LVX_6030_12_7b114.disk.bin (file size = 45,234,262 bytes)  
2.2 Xerox 8850, 510dp Print System  
The following executable is provided for the Xerox Wide Format 510dp and supports the  
Xerox Wide Format Scan System scanner and GFI finisher.  
YKE/YKEN/FRX/LVX Controller:  
YKE_YKEN_FRX_LVX_510DP_12_7b114.disk.bin (file size = 45,566,897 bytes)  
2.3 Xerox Print System 721p  
The following executable is provided for the Xerox Wide Format Print System 721p and supports  
the Xerox Wide Format Scan System scanner and GFI finisher.  
YKE/YKEN/FRX/LVX Controller:  
YKE_YKEN_FRX_LVX _721P_12_7b114.disk.bin (file size = 45,505,888 bytes)  
2.4 Xerox 6204 Wide Format Solution  
The following executable is provided for the Xerox 6204 Wide Format Solution and supports  
the Xerox Wide Format Scan System, the 6204 scanner, and GFI finisher for non-6204  
scanner configurations.  
YKEN/FRX/LVX Controller:  
YKEN_FRXLVX _6204_12_7b114.disk.bin (file size = 47,544,934 bytes)  
2.5 Xerox 6050A Wide Format Solution  
The following executable is provided for the Xerox 6050A Wide Format Solution and supports the  
Xerox Wide Format Scan System and GFI finisher.  
FRX/LVX Controller:  
FRX_LVX_6050A_12_7b114.disk.bin (file size = 45,567,562 bytes)  
Page 5  
 
2.6 Xerox 8825/8830 Print System  
The following executable is provided for the Xerox Wide Format 8825/8830 and supports the  
Xerox Wide Format Scan System scanner and GFI finisher.  
YKE/YKEN/FRX/LVX Controller:  
YKE_YKEN_FRX_LVX_8830_12_7b114.disk.bin (file size = 45,560,123 bytes)  
Page 6  
 
3 Recommended Configurations  
The following table specifies the RAM requirements for the various systems and configurations  
supported by the FreeFlow Accxes controller.  
YKE Controller  
YKE-N Controller  
FRX Controller  
LVX Controller  
System  
Min Recommend Min Recommend Min Recommend Min Recommend  
510, 721,  
6030, 6050,  
8825, 8830,  
8850  
1GB 1GB  
1GB 1GB  
1GB 1GB  
1GB 1GB  
6204  
NA  
NA  
NA  
NA  
1GB 1GB  
1GB 1GB  
1GB 1GB  
1GB 1GB  
1GB 1GB  
1GB 1GB  
1GB 1GB  
6050A  
NA  
NA  
Any System 1GB 1GB  
with  
1GB 1GB  
AutoCAD,  
OtherCAD,  
or RASTER  
feature key  
Page 7  
 
4 Release Installation  
NOTES:  
This version of Accxes (12.7 b 114) requires OS Install CD version 4.0 build 114 or higher.  
BSP Kernel revision 2.6.22.9-61.fc6 or later is also required. Service is required to upgrade  
from earlier Accxes® revisions.  
Regarding scanner firmware revisions: If you are upgrading the firmware of a system containing  
a Xerox Wide Format Scanner, you must also ensure that the scanner firmware is upgraded,  
prior to upgrading the controller, to the following version:  
.
Xerox Wide Format Scanner – version 2.2.4 or greater. Version 3.2.6 or greater is  
needed for full functionality.  
IMPORTANT NOTE: The controller will only accept the installation when there are no active jobs  
being processed.  
4.1 Accxes Client Tools  
Download the file named “<Controller>_<Printer>_<Accxes_version>.disk.bin”. A status  
sheet will be printed and indicate that the download was successful.  
4.2 WebPMT  
Select PRINTER DEFAULTS > UTILITIES > Upload File. Use the Browse button to select  
the “<Controller>_<Printer>_<Accxes_version>.disk.bin”. Click on the “Upload” button. A  
printed status sheet will indicate that the download was successful.  
4.3 Unix  
Download the software using LPR with the following command line:  
lpr –P printername “<Controller>_<Printer>_<Accxes_version>.disk.bin”  
A status sheet will be printed and indicate that the download was successful.  
Page 8  
 
5 New Features of 12.7  
5.1 IPv6 Support  
The Accxes controller now supports IPv6 addressing. It will automatically search the local  
network for an IPv6 server and construct a Global address when it finds one. The IPv6  
Addresses are displayed on the test print and on the WebPMT Network page. At least 1GB is  
required to run in an IPv6 environment. Depending on the network and the network servers it may  
take 5 minutes to obtain a global address.  
5.2 Folder Support for Copies on 6204  
Support has been added to allow folding of copies made on the 6204 copier when using the  
embedded scanner. The folding options are listed on the “More features” tab and allow the user  
to select fold program, title-block location, margins, etc.  
5.3 PDF Transparency Flattening  
A new setting for the Flattening level of PDF files can now be selected in the WebPMT >  
Emulations > Postscript page. This setting adjusts how much memory is used when flattening  
complex PDF files with large numbers of transparent objects. The setting is at 5 which produces  
the best image output and uses the most memory. If too much memory is required the level can  
be reduced to 1 which will conserve memory enabling highly complex files to print.  
5.4 Support for Camera JPEG files  
Support has been added to the JPEG interpreter to handle many of the EXIF tags which today’s  
cameras insert into their JPEG files. This enhancement allows Accxes to properly render JPEG  
image files from most digital cameras.  
Page 9  
 
6 Release Notes  
The following information supplements the 12.5 customer user guides.  
6.1 Sets  
For 600 DPI engines (6030, 6050, 6050A, and 6204) the maximum number of ARCH E sized  
documents that will collate reliably in a set is 150. If the documents will not collate properly, one  
copy of the set will be printed only. This is for sets created using the scanner as well as printed  
sets submitted across the network.  
6.2 6204 Specific  
6.2.1 Copying ARCH-E size prints  
To maximize copying of ARCH-E size prints always copy them using the preset output format  
ARCH-E. When copied in synchro mode it is likely that ARCH-E documents will scan as 1220mm  
and will incur unneeded pauses between printing pages. The 6204 IOT will pause between pages  
which are greater than ARCH-E (48 inches 1219 mm) in length for the fuser to come all the way  
back to full temp even if it is in the nominal fuser temperature range.  
6.2.2 Specifying titleblock for copies  
When making a copy on the 6204 multi-function system which is intended to be folded you must  
specify the titleblock as seen through the facedown page. The example below shows the  
titleblock in the lower left corner:  
6204 Scanner  
Document  
Page 10  
 
6.3 6050/6030 Specific  
6.3.1 Configuring the Remote printer  
The address of the remote printer should not be changed while there is an active print job in the  
printer queue. If you attempt to change the address of the remote printer in this situation you will  
need to restart the controller in order to complete the address change.  
6.4 Controller  
6.4.1 Stamp does not appear  
If the user tries to upload a stamp files that contains an invalid format, or if the Accounting Mode is  
set to “Enabled”, no error message will be displayed. The WebPMT screen will display a message  
that the file was uploaded successfully and the stamp’s filename will not appear in the “Printer  
Resident Stamps” list. To avoid this situation, set the Job Accounting mode to “Optional” before  
uploading stamps. The WebPMT has no knowledge of the validity of any file that is sent to the  
printer. File validation and error handling is done on the printer by the FreeFlow Accxes controller.  
The WebPMT only reports that the file was sent to the printer successfully.  
6.4.2 Scaling interaction with “ANY”  
The media size “ANY” will select the best sheet size for an image to prevent clipping. If a user  
specifies a media size of “ANY” and a scale factor that makes the image too large for any sheet  
size and mismatch mode is set to scale, the controller will select the largest sheet size and scale  
the image to fit on it.  
If this is not the desired behavior, a specific sheet size can be selected, or the media mismatch  
mode can be set to QUERY.  
6.4.3 Margins may cause image clipping  
If the margins (TOP, BOTTOM, RIGHT and LEFT) are set to a non-zero value (5mm is the  
default) then that amount of whitespace will be added to the image before placing it on the media  
and could cause part of the image to be shifted off the page, or clipped. To correct this problem  
set the margins to 0.  
6.4.4 CGM Files and folding  
Certain CGM files contain rotation commands which can confuse the system when folding. If the  
titleblock is not visible or the plot is bypassed and not folded, change the titleblock location to  
obtain a correctly folded document.  
6.5 Wide Format Scanner  
Page 11  
 
6.5.1 Clear Last Image  
When the “Clear Last Image” feature is selected on the Xerox Wide Format Scan System, it may  
take a few minutes for a Photo or Color mode scanned document to clear out. After scanning a  
document, this feature is accessed by selecting the “C” key on the scanner. It will bring up the  
“CLEAR SCANNED IMAGE” screen. Use the “Next” button to select “CLEAR LAST IMAGE”, and  
then press “ENTER”.  
6.5.2 Invert Feature and Recall Last Job  
Scan a document. Press the Transform key. Select “Recall Last Job”. If the Invert feature  
(changes dark to light and vice versa) is selected before printing the recalled document, the  
document will not be inverted. It will need to be rescanned to get the inverted image.  
6.5.3 Scan-to-Print and Margins  
When performing a scan-to-print operation the scanned image is printed using the current printer  
processing defaults including margins. If the image scanned is exactly the width of the paper,  
then the processing default margins should be set to zero to prevent the image from being clipped  
or placed on a larger sheet of paper.  
6.5.4 Width Detection Sensors and Finishing  
When using the width detection sensors, if the document is a little bit off-center, this could cause  
problems for folding, as the document printed may be square. This is most problematic with A, B,  
and C sizes. Documents must be centered when using the sensors for width detection.  
6.5.5 Background Suppression  
The scanner uses the first few inches of a document to determine the background suppression. If  
the first few inches of the document being scanned are not representative of the entire document,  
either too much or too little of the background will be removed. If this occurs, try physically turning  
the document 90 degrees and scan it again. Continue with this until an edge is found that  
produces a good scan.  
6.5.6 Scaling shaded documents  
Scaling documents with error diffused shaded areas should be done in a photo mode to produce  
the best image quality. Line and normal modes tend to exaggerate the shading dots making them  
more visible.  
6.5.7 50000015 errors while copying  
Occasional 50000015 errors have been seen while scanning more than 128 documents on the  
6030/6050 system. This happens when an experienced operator gets a significant number of  
pages ahead of the printer causing a queue that is larger than the system can hold. The solution  
is to wait for several of the pages to complete printing before copying any additional documents.  
6.5.8 Recalling sets  
When a set is recalled, the scanner UI settings are not set to reflect their state for the last page  
scaled, but are in a “neutral” state to prevent unintentional overriding of setting for the set. If a  
setting (like scale, page size, etc) is changed it will affect the entire document set.  
Page 12  
 
6.5.9 Washed out documents when scanning/copying  
When scanning/copying documents with very low contrast (like poor blue line or sepia documents)  
with dynamic background removal set to OFF can cause the system to threshold the document  
and produce a very washed out document. Enabling background removal will actually remove  
less of the background in this case.  
6.6 Manual Feed  
6.6.1 Manual feed media source will be ignored when used with the  
Accxes Client Tools’ page composition feature.  
Go to Accxes Client Tools > Job Option tab > Composition tab > Select Overlay Images > Media  
Source drop down menu. Although “Manual Feed” is listed as a choice of media source for page  
composition jobs, the print job will be treated as if AUTO media source was selected. If an  
appropriate roll of media is available, it will be printed on that media; otherwise, the job will query  
until the correct roll media is installed. In addition, other Media Source selections will be treated  
as AUTO if an appropriate roll of media is available in a different roll.  
6.7 Instant Access  
6.7.1 InstantAccxes Folders not browse-able on IPv6  
When using InstantAccxes folders on an IPv6 network you must reference the system directly as  
shown below:  
Vista: Start>Run> \\<Controller Name>  
Linux: smb://<Controller Name>  
6.7.2 InstantAccxes Folders not accessible from MAC on IPv6  
InstantAccxes folders are not accessible to systems running MAC OS 10.4 or earlier versions on  
IPv6 networks.  
6.8 Web Print Manager Tool (WebPMT)  
6.8.1 Printer Queue – Main WebPMT Screen  
The FreeFlow Accxes Controller supports a maximum of 120 active printer jobs in the queue and  
8 active copy jobs. If subsequent jobs are sent before the 128th prints, ports will refuse  
connections and there can be scan errors; when there are fewer jobs in the queue, the jobs can  
then be resubmitted or scanned. Additionally, completed jobs will be removed from the queue  
display immediately to make room for the newly submitted print jobs. To avoid these issues, keep  
the number of active print jobs to under the 128 limit.  
NOTE: More than 128 files can be sent from the Document Submit Tool as one print job, but all of  
the files in the print job must have printed before sending subsequent jobs, or the jobs will be  
refused.  
Page 13  
 
6.8.2 German users only  
Zum Drucken von Etiketten mit Umlauten DRUCKERVORGABEN > DRUCKER-EINSTELLUNG  
> Plot-Etiketten wählen.  
Anschließend im Dropdown-Menü für Fonts einen der folgenden Fonts wählen: HP2 Stick Font  
Latin - 1 oder HP2 Stick font Latin - 1 – Proportional.  
6.8.3 Large Scaling Factors  
Images set to scale beyond the largest installed roll will not scale beyond the largest width unless  
a specific roll is selected, a specific page size is selected, or mismatch mode is set to something  
other than scaling. This is a behavior that has changed from previous releases (prior to 9.0).  
For example: The largest roll installed is 36". Scaling is set to 999%. Submit an ARCH E sized  
drawing (Media Size = Any, Mismatch = Scaling). The drawing will not be scaled.  
In order for the output to exhibit the desired scaling factor, one of the following conditions must be  
met:  
What to do:  
Set Mismatch Mode to Substitute  
Request a Media Size of ARCH E via WebPMT, ACT, or the Driver  
Request a Media Size 36" Roll via WebPMT, ACT, or the Driver  
6.8.4 HPGL Page – End of File  
If the files are streamed via any port on the system, these are treated as a single job and no reset  
is done between them. However, if one uses the LPD protocol to send the files one at a time, the  
effect is that the printer is reset after each job. If the “Reinitialize after EOF” is set to be on, the  
FreeFlow Accxes firmware will reset the printing parameters after each plot file that is received by  
a serial port or a parallel port. To reset the HPGL parameters on the WebPMT, select Printer  
Defaults > Emulations > HPGL. Click on the box in front of “Reinitialize after EOF”. Click on the  
“UPDATE PRINTER” button.  
6.8.5 Display of Media Usage  
The WebPMT Linear Media Usage displays the Media Usage in METERS. The mechanical  
meters used on the Xerox Wide Format Print System 721p IOTs can be programmed using the  
IOT diagnostics and are determined by which mode (ANSI or ISO) that the IOT is programmed to  
operate in. The units of measurement may not be the same.  
6.8.6 Default PostScript Page Size  
If a PostScript job does not specify a page size (either by using a compatibility operator such as  
“letter”, or “a4”, or by using the setpagedevice operator /PageSize parameter), the page size used  
is the one specified by the Default PostScript Page Size parameter available via the printer user  
interface, or via the WebPMT.  
6.8.7 “Printer has been updated” message  
If the user presses the “UPDATE PRINTER” button without actually making changes first, the  
WebPMT will still return a message that the printer was updated. The WebPMT cannot  
distinguish a page that has been modified from one that has not been modified. This is because  
of the “stateless” nature of the http protocol and the fact that no events are generated (html) when  
text values are entered or items are selected. When the “UPDATE PRINTER” button is pressed,  
all the data on the form is gathered and sent to the server. If the data is valid, the printer is  
updated and “The printer was updated successfully.” message is returned. If inappropriate data is  
Page 14  
 
sent, an error message is returned. To verify valid changes to printer settings, a test print can be  
printed to view the changed settings.  
6.8.8 Disk Image Overwrite  
6.8.8.1 OVERVIEW  
The Disk Image Overwrite feature has two operations: Immediate and On Demand. The  
immediate operation overwrites image data on the hard drive immediately after it is no longer  
needed (i.e. When the page has printed). The On Demand operation cleans the entire disk. Both  
On Demand Image Overwrite and Immediate Image overwrite feature are configured by the  
system administrator, assuming that the system administrator password is set to a non-zero  
value.  
6.8.8.2 ALGORITHM  
The overwrite algorithm for both IIO and ODIO conforms to the U.S. Department of Defense  
Directive 5200.28-M (Section 7, Part 2, paragraph 7-202), and is common to all  
WorkCentre/WorkCentre Pros and AccXES controllers.  
The algorithm for the Image Overwrite feature is:  
Step 1: Pattern #1 is written to the sectors containing temporary files (IIO) or to the entire spooling  
area of the disk (ODIO). (hex value 0x35 (ASCII “5”)).  
Step 2: Pattern #2 is written to the sectors containing temporary files (IIO) or to the entire spooling  
area of the disk (ODIO). (hex value 0xCA (ASCII compliment of 5)).  
Step 3: Pattern #3 is written to the sectors containing temporary files (IIO) or to the entire spooling  
area of the disk (ODIO). (hex value 0x97 (ASCII “ú”)).  
Step 4: 10% of the overwritten area is sampled to ensure Pattern #3 was properly written. The  
10% sampling is accomplished by sampling a random 10% of the overwritten area.  
See Online Help in WebPMT for more details about using the Image Overwrite feature.  
Page 15  
 
7 Customer Issues Resolved  
7.1 The following customer issues were resolved  
in 12.7 b 114  
Issue Description  
Problem  
Resolution  
SPAR# 041643618 – A DWF file with markups  
The DWF interpreter was  
upgraded to support  
markups correctly  
DWF markups  
printed on separate  
pages  
would print the image and  
the markups on separate  
pages  
SPAR# 326784478 – Certain Czech. Fonts would  
The Adobe Postscript  
Czech. Fonts in PDF not print correctly when used interpreter was upgraded to  
files are not printing  
correctly.  
in PDF files.  
support these fonts.  
SPAR 638826124 –  
Copies and Scan-to-net files The TRC curve for the Wide  
speckled scan to net of near white paper showed  
images tiny dots or speckles.  
Format scanner was  
modified to correctly  
reproduce these near white  
colors as white.  
SPAR# 499374656 – The fold program selection  
The InstantAccxes page was  
fixed to allow all fold  
programs to be selected.  
Fold programs not  
correctly selected in  
InstantAccxes  
on the WebPMT >  
InstantAccxes page did not  
allow the user to select the  
last two fold programs.  
SPAR# 578692123 – Certain complex DWF files  
The DWF interpreter was  
enhanced to be more  
memory efficient so the files  
will now print.  
DWF memory  
Allocation  
would not print and issued  
an out of memory error  
message.  
7.2 The following customer issues were resolved  
in 12.6 b 101  
Issue Description  
Problem  
Resolution  
SPAR# 107111928  
– Color scan to net  
produced 50000013  
error on scanner UI.  
Scanning color scan with  
output format of Packbits  
TIFF caused error with long  
originals.  
Color TIFF scans accepted  
up to 10 feet.  
SPAR# 350573348  
– Recall of color  
scan template turns  
off background  
Lightness/Darkness LEDs  
forced off when image type  
set to color for default  
template.  
LEDs function properly when  
color selected as default  
image type.  
suppression and  
Page 16  
 
lightness/darkness.  
7.3 The following customer issues were resolved  
in 12.5 b 120  
Issue Description  
Problem  
Resolution  
SPAR# 683775429  
– DHCP not setting  
gateway and  
Accxes used calls to retrieve Accxes properly queries the  
gateway and netmask that  
returned improper values.  
OS to get the gateway and  
netmask.  
netmask.  
SPAR# 893836717 – CGM plot file that plots  
Lines printed inside circle.  
CGM file not printed  
properly.  
ellipse with lines outside  
circle. Lines  
should be inside.  
Scan to FTP to HP  
printer fails.  
An incompatibility existed  
between newer versions of  
the HP FTP server and  
Accxes when logging in.  
Incompatibility was resolved  
to allow login process to  
succeed.  
7.4 The following customer issues were resolved  
in 12.2 b 107  
Issue Description  
Problem  
Resolution  
SPAR# 335098581 – Selection of different image  
The correct image type  
6204 Copier Image  
Types  
types on the 6204 scanner  
did not request specific  
image type processing.  
processing is now called for  
each image type that can be  
selected.  
SPAR# 705110594 – Certain PDF files would print Fonts now print as expected.  
PDF Font prints as  
boxes  
boxes for some fonts.  
Page 17  
 
7.5 The following customer issues were resolved  
in 12.2 b 102  
Issue Description  
Problem  
Resolution  
SPAR#568936962 – MediaBox dimensions were  
When “use drawn area” is  
PDF not printing  
according to  
CropBox  
always used for printing PDF selected the “CropBox”  
files  
dimensions are now used for  
image size.  
7.6 The following customer issues were resolved  
in 12.2 b 101  
Issue Description  
Problem  
Resolution  
SPAR#628160720 – Non-square CGM patterns  
CGM pattern fill did not print correctly.  
Pattern handling was  
enhanced to support non-  
square patterns.  
SPAR# 372757329 – An invalid font definition in a  
Adobe provided a fix which  
no longer crashes, but  
renders the page without  
printing text using the font.  
The Adobe interpreter also  
provides no indication of  
problem.  
Crash while printing  
PDF file  
PDF file causes the Adobe  
PS interpreter to crash.  
SPAR# 76492593 –  
6204 UI not  
recalling all STN  
settings .  
When recalling a scanning  
template on the 6204, the  
format always reverts to  
TIFF.  
Image type for scanning is  
now included in the scanner  
template.  
SPAR# 312764109 – Scan-to-FTP functionality  
Corrected QUIT command  
handling to correspond with  
Novell implementation.  
Novel FTP  
was not working when  
submitting to certain  
versions of Novell.  
6204 Image Type  
selection not  
functional  
Copies made with different  
Image Type settings did not  
yield different image quality.  
Enhanced the image quality  
of the non-default Image  
Type settings on the 6204  
copier.  
Page 18  
 
7.7 The following customer issues were resolved  
in 12.1 b 110  
Issue Description  
Problem  
Resolution  
SPAR# 668881988 – When printing from  
The accuracy of the  
resolution conversion for  
fonts (and other objects) was  
increased to ensure  
consistent plotting of these  
elements.  
TrueType fonts not  
uniform width  
AutoCAD 2006 application,  
many characters from  
TrueType fonts were printed  
with varying thicknesses.  
SPAR# 557924048 – Certain standard fonts were  
Adobe corrected the problem  
with their code and it was  
integrated into v 12.1 of  
Accxes.  
Certain PDF file not  
printing correctly  
not being printed correctly  
when referenced in certain  
PDF files.  
SPAR# 298073435 – On a 510 printer (or 8830,  
WebPMT would only 8825, 8850) the new 12.0  
The language selection for  
the 510 and 88XX series  
printers was corrected to use  
the actual language  
display English and  
Italian on 510  
printers  
Web interface would select  
the language based on  
secondary/primary language, selected.  
not by the actual language  
selected..  
Issues with the  
Russian translation  
for the Web interface on the Web interface for the  
Russian language.  
Several Characters/words  
were not properly displayed  
The translation files were  
corrected and they should  
now display correctly.  
SPAR #065384983 - The PDF file in this SPAR  
The PostScript “image”  
operator was re-defined to  
better handle invalid image  
data.  
Missing Data File  
did not conform to the PDF  
generates error page specification, but it did open  
offending command  
IMAGE.  
in Acrobat.  
Page 19  
 
Prepared by:  
Xerox Corporation  
800 Phillips Road  
Building 139-26A  
Webster, New York 14580-9791  
USA  
©XEROX Inc. 2007. All rights reserved.  
Printed in the United States of America  
XEROX®, XEROX Wide Format 6204, 6030, 6050, 6050A, 510, 721, 8825, 8830, 8850, Xerox  
Wide Format Scan System, FreeFlow® Accxes®, and acronyms, are trademarks of XEROX  
CORPORATION.  
12/2007  
Page 20  
 

Weider Home Gym PRO 408 User Manual
Wharfedale Portable Speaker 105T User Manual
Whirlpool Double Oven W10748900C User Manual
Whirlpool Universal Remote 1180435 A User Manual
Woodstock Switch D4159 User Manual
Xerox Printer 4260C User Manual
Yamaha DJ Equipment IMX644 User Manual
Zanussi Refrigerator ZC135R User Manual
Zenoah Chainsaw G3400 User Manual
Zephyr Fan AK2000 User Manual