Williams Sound Satellite Radio PFM 300 User Manual

MANUAL AND USER GUIDE  
HEARING HELPER Personal FM System  
Wireless FM Listening System  
Models PFM 350, PFM 300, PFM 350E RCH, & PFM 300E RCH  
Transmitter Model PFM T32  
Optional Receiver Models PFM R32, R31  
MAN 072H  
 
SYSTEM OVERVIEW  
Thank you for purchasing the Hearing HelperPersonal FM System from Williams Sound Corp.  
Anyone needing auditory assistance to overcome background noise, reverberation, or distance from  
the sound source can benefit from the Personal FM System.  
Your PFM System has two principal parts: the Transmitter and the Receiver. Much like a miniature  
radio station, the Transmitter and microphone pick up the sounds you want to hear and broadcast  
them over an FM radio signal. The receiver and earphone are used to pick up the broadcast up to 100  
feet away.  
To avoid difficulties, please read through these instructions as you begin to use the system. Then save  
them for questions that arise as you continue to use your Williams Sound Personal FM System.  
If you have problems with the PFM system, don’t hesitate to call us toll-free at  
1-800-843-3544.  
FIGURE 1: HOW THE PFM SYSTEM WORKS  
FM Radio Signal  
Speaker Uses Transmitter  
With Microphone  
Listeners use R31 or R32 Receivers with  
Earphones, Headphones, Or Neckloop  
The speaker wears the body-pack transmitter and a clip-on microphone. The speaker’s  
voice is broadcast as an FM radio signal over a distance of 100-150 feet (30-45 m).  
Listeners use the pocket receiver and earphone or headphone to hear the speaker’s  
voice directly, with reduced background noise. A neckloop telecoil coupler allows the  
system to be used with telecoil (T-Switch) equipped hearing aids.  
3
 
SYSTEM COMPONENTS  
Body Pack Transmitter (PFM T32) with (2) AA batteries (BAT 001)  
Lavalier microphone (MIC 090)  
Mini earphone (EAR 013)  
Soft Nylon System Carry Case (CCS 020)  
(2) Belt clip cases (CCS 001)  
Instructions (MAN 072)  
PFM System 300 Only:  
Personal FM Receiver (PFM R32) with (2) AA batteries (BAT 001)  
PFM System 350 Only:  
Personal FM Receiver (PFM R31) with Plug Mount Microphone (MIC 014)  
and (2) AA batteries (BAT 001)  
PFM System 300E RCH Only:  
Personal FM Receiver (PFM R32) with CHG 200A Drop-in Charger and (2) AA NiMH  
rechargeable batteries (BAT 026)  
PFM System 350E RCH Only:  
Personal FM Receiver (PFM R31) with CHG 200A Drop-in Charger and (2) AA NiMH  
rechargeable batteries (BAT 026)  
FIGURE 2: SYSTEM COMPONENTS  
Williams Sound  
Williams Sound  
Williams Sound  
Hearing Helper®  
Hearing Helper®  
Hearing Helper®  
R32 Receiver  
T32 Transmitter  
R31 Receiver  
(PFM 300 & 350 Systems)  
(PFM 300 System)  
(PFM 350 System)  
4
 
SAFETY INFORMATION  
HEARING SAFETY  
CAUTION!  
This product is designed to amplify sounds to a high volume level which could poten-  
tially cause hearing damage if used improperly. To protect your hearing and the hear-  
ing of others:  
1. Make sure the volume is turned down before putting on the earphone or headphone before  
adjusting the volume to a comfortable level.  
2. Set the volume level at the minimum setting that you need to hear.  
3. If you experience feedback (a squealing or howling sound), reduce the volume setting and  
move the microphone away from the earphone or headphone.  
4. Do not allow children or other unauthorized persons to have access to this product.  
BATTERY SAFETY AND DISPOSAL  
CAUTION!  
This product is supplied with disposable Alkaline batteries. Do not attempt to recharge  
disposable batteries, which may explode, release dangerous chemicals, cause burns, or  
other serious harm to the user or product.  
PACEMAKER SAFETY:  
CAUTION!  
1. Before using this product with a pacemaker or other medical device, consult your physician  
or the manufacturer of your pacemaker or other medical device.  
If you have a pacemaker or other medical device, make sure that you are using this product in  
accordance with safety guidelines established by your physician or the pacemaker manufacturer.  
2.  
RECYCLING INSTRUCTIONS  
BATTERY SAFETY AND DISPOSAL  
Help Williams Sound protect the environment! Please take the time to dispose of your  
equipment properly.  
Product Recycling for Customers in the European Union:  
Please do NOT dispose of your Williams Sound equipment in the household trash. Please take the  
equipment to a electronics recycling center; OR return the product to the factory for proper disposal.  
Battery Recycling for Customers in the European Union:  
Please do NOT dispose of used batteries in the household trash. Please take the batteries to a  
retail or community collection point for recycling.  
12/27/06  
5
 
USING THE PFM T32 TRANSMITTER  
1. Install two (2) AA batteries. If you’re using rechargeable batteries, they must be charged before  
using. See battery information on page 13.  
2. Plug the microphone cord into the “Mic” jack on top of the transmitter.  
FIGURE 3: T32 TOP VIEW  
3. Place the transmitter in the belt clip case provided.  
4. Slide the Power Switch on top of the transmitter to “On.” The Power ON LED indicator should illumi-  
nate Red.  
5. The microphone should be placed as close to the speaker’s mouth as is practical. For lapel mics, attach  
the microphone to a collar, lapel, or tie.  
6. When you are ready to speak, turn the Mic Mute Switch (speaker icon) to the “On” position. When you are done  
speaking, mute the mic by turning the Mute Switch to the “Off” position (speaker icon with line through it).  
The transmitter can be placed in a pants pocket, or clipped onto a belt or waistband.  
FIGURE 4: CORRECT MICROPHONE PLACEMENT  
Yes  
Yes  
No  
The PFM System comes with an omnidirectional, lapel-clip style microphone. It should be  
clipped to a collar, lapel, tie, or neckline as close to the mouth as possible and centered  
on the body as shown.  
Note On The Transmitter Antenna:  
The microphone cord is the transmitting antenna. Do not bunch up the cord or wrap it  
around the transmitter. For maximum range, the cord should hang as straight as possible.  
6
 
CHANGING THE PFM T32 FREQUENCY  
FIG. 5: PFM T32 FREQUENCY CHANGE  
By default, the T32’s frequency is to set 72.9 MHz (Channel E). If you experience FM interference, or  
if you need to match a receiver’s frequency, it may be necessary to adjust the frequency on the T32.  
Instructions:  
1.Open the battery compartment using a coin in the slot in the bottom of the transmitter. Remove the  
batteries.  
2. Lift the battery compartment door up and pull to your left to expose the circuit board.  
3.Refer to FIG 5 to locate the Channel Switch.  
4.Use a small screwdriver to rotate the Channel Switch to correspond with the desired operating fre-  
quency. Choose between 16 standard channels. Refer to the Channel Selection Chart in FIG 5 for  
available channels.  
5. Reinstall the batteries, then close the back of the transmitter.  
6. Plug the microphone in and turn the transmitter on to provide a tuning signal for the receivers.  
Important: Make sure all receivers being used match the frequency of the transmitter. Refer to the  
receiver’s instruction manual for frequency change instructions.  
7
 
ADVANCED FEATURES ON THE PFM T32  
Gain Control Adjustment  
FIG. 6: T32 ADVANCED FEATURES  
If necessary, the microphone gain control on the T32  
can be increased or decreased to meet the demands of  
specific listening applications.  
Instructions:  
1.Open the battery compartment using a coin in the  
slot in the bottom of the transmitter. Remove the  
batteries.  
2. Lift the battery compartment door up and pull to  
your left to expose the circuit board.  
3. Refer to FIG 6 to locate the microphone gain con-  
trol.  
4. Using a small screwdriver, turn the gain control  
fully counterclockwise to reduce the gain. Turn the  
gain control fully clockwise to increase the gain  
5. Close the back of the case and battery door.  
COMPRESSION ADJUSTMENT  
By default, the T32 transmitter compression jumper is set to “Off” for normal operation, or 1:1 compression.  
For hearing assistance applications, the compression jumper can be set to “On” for 2:1 compression.  
Instructions:  
1.Open the battery compartment using a coin in the slot in the bottom of the transmitter. Remove the batteries.  
2. Lift the battery compartment door up and pull to your left to expose the circuit board.  
3. Refer to FIG 6 to locate the Compression Selector.  
4. Gently remove the jumper from the circuit board by pulling it up and away from the unit. You will see  
three exposed “pins.”  
To turn compression “On” (2:1 Compression): Press jumper on to the top two pin locations as shown  
on left.  
To turn compression “Off” (1:1 Compression): Press jumper on to the bottom two pin locations as  
shown on left.  
5. Close the back of the case and battery door.  
8
 
USING THE PFM R32 RECEIVER (PFM 300 & PFM 300E RCH):  
Receiver model PFM R32 has a single volume control and an earphone output jack.  
1. Make sure there are two charged AA batteries in the Receiver. If batteries are not installed, see  
Battery Information on page 13.  
2. Plug the earphone or headphone into the “Ear” jack on top of the Receiver.  
FIGURE 7: R32 RECEIVER TOP VIEW  
On  
Indicator  
FM  
Earphone  
Jack  
EAR  
On  
Volume  
Control  
FM Indicator  
FM  
Off  
Max  
3. Turn the power on by rotating the volume control knob on top of the Receiver.  
4. Place the earphone in your ear.  
5. Choose the correct channel using the right switch on the R32’s back panel.  
Unless you have changed the Transmitter channel, set the receiver to channel 1. If the Transmitter  
is on and tuned to channel 1, the FM Indicator light on the R32 will light.  
FIGURE 8: RECEIVER TONE & CHANNEL CONTROLS  
TONE  
Channel  
CH1 CH2  
Lo Mid Hi  
6. Adjust the receiver volume control to a comfortable listening level.  
You should be able to hear someone speaking into the Transmitter microphone.  
7. Adjust the receiver tone control to your needs. Lo – more low frequencies;  
Mid – some low frequency cut; Hi – maximum low frequency cut, emphasizes higher frequencies.  
(See Figure 8.)  
8. Place the Receiver in the belt clip case provided. The Receiver can be placed in a pants pocket, or  
clipped onto a belt, harness, or waistband.  
Notes:  
The earphone cord is the receiving antenna. Do not bunch up the cord or wrap it around the receiver.  
For best reception, the cord should hang as straight as possible. Make sure the Receiver is turned  
OFF when not in use. The channel selector can be used to switch between an individual and a group  
channel.  
9
 
USING THE PFM R31 RECEIVER (PFM 350 & PFM 350E RCH):  
Receiver model PFM R31 has two volume control knobs (one for the FM signal, one for  
environmental sounds), a microphone input jack, and an earphone output jack.  
1. Make sure there are two charged AA batteries in the Receiver. If batteries are not installed,  
see Battery Information on page 13.  
2. Insert the small Plug Mount Microphone (MIC 014) into the “Mic” jack on top of the  
R31 Receiver.  
FIGURE 9: R31 TOP VIEW  
FM Volume  
FM  
On Indicator  
Mic Jack  
Mic  
Volume  
Mic  
EAR  
MIC  
On  
FM  
Indicator  
Mic  
Jack  
FM  
Off  
Max Min  
Max  
3. Plug the earphone or headphone into the “Ear” jack on top of the Receiver.  
4. Turn the power on by rotating the taller “FM” volume control on top of the Receiver.  
5. Place the earphone in your ear.  
FIGURE 10: RECEIVER TONE & CHANNEL CONTROLS  
TONE  
Channel  
CH1 CH2  
Lo Mid Hi  
6. Choose the correct channel using the right switch on the R31’s back panel. If the  
Transmitter is on and tuned to channel 1, the FM Indicator light on the R31 will light.  
7. Adjust the receiver tone control to your needs. Lo – more low frequencies;  
Mid – some low frequency cut; Hi – maximum low frequency cut, emphasizes higher fre-  
quencies. (See Figure 10.)  
8. Place the Receiver in the belt clip case provided. The Receiver can be placed in a pants  
pocket, or clipped onto a belt, harness, or waistband.  
10  
 
Notes:  
The earphone cord is the receiving antenna. Do not bunch up the cord or wrap it around the receiver. For  
best reception, the cord should hang as straight as possible. Make sure the Receiver is turned OFF when  
not in use. The channel selector can be used to switch between an individual and a group channel.  
Adjusting The R31 Volume Controls  
1. Adjust the taller “FM” volume control to a comfortable listening level. You should be able to hear  
someone speaking into the Transmitter microphone.  
2. Now adjust the shorter “Mic” volume control until you can hear sounds picked up by the environ-  
mental microphone on top of the receiver.  
3. Adjust the two volume controls for a comfortable mix of FM and environmental sounds.  
You will normally want to have the FM signal louder than the environmental Mic signal to  
avoid picking up extra background noise. If no environmental sounds are desired, turn the  
“Mic” control fully to “Min”. If you want to hear nearby conversation or your own voice, turn  
the “Mic” control up.  
11  
 
TUNING THE PFM R32 & R31 RECEIVERS  
Tuning for the R32 and R31 Receivers is determined by tuning coils, and is stabilized by phase-  
locked-loop circuitry. A plastic tuning wrench (PLT 005) is needed to adjust the receiver tuning coil.  
1. Use the Transmitter as a tuning signal source. Have someone speak into the microphone so you  
have something to listen to.  
2. Keep the Transmitter and Receiver about 15 - 20 feet apart while tuning. The receiver must be  
tuned under weak signal conditions.  
3. Open the battery compartment using a coin in the slot in the bottom of the transmitter. Pull up  
the receiver battery flap to open the receiver back like a book. This will expose the circuit board.  
4. Move the channel selector switch to channel 2 (right position).  
5. Use Figure 11 below to locate the tuning coils. Use the earphone supplied with the receiver to  
listen for the transmitter signal while you slowly and gently rotate the tuning slugs inside the tun-  
ing coil with the tuning wrench. Adjust the tuning coil for channel 2 slowly and carefully. Do not  
press down on the tuning slug. Adjust for maximum signal.  
6. Re-tune all the receivers and mark the new frequency inside the case for future reference.  
FIGURE 11: LOCATION OF RECEIVER TUNING COILS  
Channel 1 Tuning Coil  
Channel 2  
Tuning Coil  
Channel Selector Switch  
Batteries  
R31/R32 Receiver  
12  
 
BATTERY INFORMATION  
INSTALLATION  
Open the battery compartment using a coin in the slot in the bottom of the receiver or transmit-  
ter. Press the batteries into place, observing proper battery polarity. Incorrect insertion of the  
battery is difficult, and if forced, may cause both mechanical and electrical damage to transmit-  
ters or receivers not covered by the five year warranty. Units will not work with the battery  
incorrectly installed.  
FIGURE 12: BATTERY INSTALLATION  
Rear of Transmitter  
or Receiver  
+
Battery  
Compartment  
Pry  
Slot  
+
Note Proper  
Polarity  
DISPOSABLE BATTERIES  
In normal use, two AA 1.5 V alkaline batteries will last about 30 hours in the T32. The batteries  
will last approximately 80 hours in the R32 and R31 Receivers, respectively.  
If the sound becomes weak or distorted, replace the battery. The indicator light may still be on,  
even with a battery that is weak. Do not leave dead batteries in the receivers! Battery corrosion is  
not covered by the Williams Sound five year warranty.  
RECHARGEABLE BATTERIES  
The PFM 350 and PFM 300 Systems can use rechargeable AA batteries (BAT 026). On an  
overnight charge, these NiMH batteries are designed to operate for 20 hours in a T32 Transmiter.  
The R32 and R31 Receivers will last for 50 and 60 hours, respectively.  
Note: The battery installed in the receiver may be recharged in the receiver only if it is a NiMH battery, and  
only if the Williams Sound CHG 200A charger is used. Damage from improper charging is not covered by  
the Williams Sound five year warranty. For charging directions, see figure 13.  
!! IMPORTANT WARNINGS !!  
DO NOT ATTEMPT TO RECHARGE ZINC CARBON (“HEAVY DUTY”), ALKALINE, OR LITHIUM BATTERIES!  
DO NOT ATTEMPT TO RECHARGE DISPOSABLE BATTERIES! These batteries may heat up and  
explode, causing possible injury and damage to the equipment.  
Avoid shorting the plus and minus battery terminals together with metal objects. Battery damage  
and burns can result!  
Use only Williams Sound Supplied chargers and batteries!  
13  
 
FIGURE 13: USING THE OPTIONAL CHG 200A BATTERY CHARGER TO CHARGE  
TRANSMITTERS AND RECEIVERS  
Step 1:  
Plug the CHG 200’s power supply into  
the Power Input on the charger’s side  
and a standard AC wall outlet.  
Step 2:  
Route the power cord around the Cord  
Hook (see figure at right). This will  
minimize strain on the cord and jack  
and insure that the power cord is not  
detached during charging.  
Charging  
Contact Holes  
Step 3:  
Step 4:  
Make sure the receivers/transmitters to  
be charged are turned OFF.  
Place the receivers/transmitters in the  
slots so that the CHG 200’s Charging  
Pins and receiver’s side panel contacts  
are coupled. Make sure that the charg-  
ing contact holes line up with the  
charging pins. The receivers should  
drop easily into the slots. DO NOT  
FORCE THEM IN BACKWARDS.  
Charging  
Indicators  
Charging  
Pins  
Step 5:  
The Charging Indicators will light, indi-  
cating that charging is in process.  
It takes 14–16 hours to fully charge the  
batteries. Remove the receivers when  
charging is completed.  
Cord Hook  
Power Input  
FURTHER SUGGESTIONS  
Receivers and Transmitters SHOULD NOT be left charging continuously when not in use.  
Receivers should always be turned OFF while charging.  
It’s best to allow the batteries to fully discharge before charging.  
If the batteries are near end of life and the LED turns off while the receiver is operating, this is an indication to  
change or recharge your batteries. Approximately one hour of battery life remains.  
Repeatedly charging the batteries after short periods of use (1-2 hours) will shorten battery life.  
Rechargeable batteries will need to be replaced after 1–2 years of use.  
!! WARNING !!  
DO NOT ATTEMPT TO RECHARGE DISPOSABLE BATTERIES!  
The batteries may heat up and burst, causing possible injury and damage to the equipment.  
Avoid shorting the plus and minus battery terminals together with metal objects. Battery damage and  
burns can result!  
Use only Williams Sound supplied chargers and batteries.  
14  
 
USING YOUR PERSONAL FM SYSTEM WITH A HEARING AID  
If you have a hearing aid equipped with a Telecoil (T-Switch), you can use a Neckloop  
(NKL 003–children’s size, or NKL 001–adult’s size) to magnetically couple the signal from the  
PFM Receiver into your hearing aid.  
The Neckloop plugs into the earphone jack of the receiver. Turn the switch to the “T” position on  
your hearing aid and adjust the volume control on the receiver to a comfortable level. If you have  
two hearing aids with telecoils, the signal will couple into both hearing aids (when using a silhou-  
ette).  
Direct Audio Input cords can be used with compatible hearing aids as well as with Cochlear Implant  
Processors. If your hearing aid has a direct audio input boot, you can obtain a cord from your hear-  
ing aid manufacturer to plug directly into the PFM receiver. The cord should have a 3.5 mm plug.  
APPLICATIONS FOR VARIOUS HEARING LOSS LEVELS  
The Personal FM is designed to provide hearing assistance for anyone when background noise or  
distance from the sound source make listening difficult. The microphone and transmitter are placed  
close to the desired sound source to help minimize background noise and to effectively eliminate  
the distance between the listener and the sound source. Because hearing ability varies, three cate-  
gories of amplification have been delineated:  
NO HEARING LOSS – LOW AMPLIFICATION  
Among Low Amplification applications are classroom and similar uses. The PFM System can be  
used with headphones or earphones for Central Auditory Processing Disorders, Learning  
Disabilities, or Attention Deficit Disorders. The PFM System is used primarily to boost speech  
sounds above other background noises, making it easier for the listener to focus on what is being  
said. The optional Rugged Headphone (HED 022–children’s size, and HED 021–adult’s size) are  
recommended for this application. The EAR 013 Single Mini Earphone, EAR 008 Surround  
Earphone, or EAR 014 Dual Mini Earphone can also be used.  
MILD – MODERATE HEARING LOSS  
These applications include the classroom, TV listening, car riding, and one-on-one conversations.  
The PFM System can be used with the Single or Dual Mini Earphone (EAR 013 or EAR 014)  
for moderate amplification fittings. The PFM System is also suitable for temporary mild hearing  
loss due to Otitis Media. The Rugged Headphones (HED 021) or Surround Earphone (EAR 022  
or EAR 008) are recommended since they do not enter the ear canal.  
SEVERE – PROFOUND HEARING LOSS  
These applications include the classroom, TV listening, car riding, and one-on-one conversations.  
For severe to profound hearing loss, the PERSONAL FM System should be used in conjunction  
with a hearing aid. A Neckloop can be used with hearing aids that have a telecoil. An adaptor  
cord can be used with hearing aids that have direct audio input  
15  
 
IN CASE OF DIFFICULTY  
If your Personal FM System is not working, check the following:  
1. Read through the manual and user guide carefully to verify proper setup and installation  
of your system.  
2. Make sure the batteries are fresh or completely charged and that the “plus” and “minus” termi-  
nals are installed correctly.  
3. If the rechargeable batteries will only work for a short period of time (less than 1 hour) even  
after they are fully charged, they must be regenerated. Leave them in the receiver or transmitter  
with the unit turned on, for 5 - 6 hours. Then turn receiver or transmitter off, place it in the  
charger, and charge for 14 - 16 hours. This should restore normal battery life. Rechargeable bat-  
teries will gradually lose their capacity over time and should be replaced every year.  
4. Make sure the microphone is plugged into the T32 Transmitter and the earphone is plugged into  
the Receiver.  
5. If you have the PFM System 350, make sure the R31 Receiver’s plug mount microphone IS  
NOT plugged into the Transmitter.  
6. If you’re using the PFM System 350 with the PFM R31 Receiver, make sure that the earphone  
has been plugged into the earphone jack and not into the R31 Receiver’s microphone jack.  
7. Move the Transmitter and Receiver closer together. You may be out of range. When using the  
system indoors, it’s normal for the signal to momentarily disappear in certain locations. This is  
called a “drop-out.” Moving a few feet will restore the signal.  
8. Make sure that the Transmitter and Receivers are tuned to the same channel. The units have  
stickers inside the back cover identifying the channel. Unless the Transmitter channel has been  
changed, set the Receiver to channel 1.  
9. Do not try to use more than one Transmitter on the same channel in close proximity to each  
other. MORE THAN ONE TRANSMITTER ON THE SAME CHANNEL WILL RESULT IN  
INTERFERENCE IF THEY ARE CLOSE TOGETHER. Keep the systems 50 - 100 feet apart  
or use separate channels for each system used.  
10. If you are still hearing interference on the Receivers, turn the Transmitter off and listen with a  
receiver. If you hear the interference with the Transmitter off, you need to change to a clear  
channel. See the re-tuning instructions.  
11. If problems remain, contact your dealer for further help. Or call Williams Sound toll-free at  
1-800-843-3544.  
16  
 
Limited Warranty  
Williams Sound products are engineered, designed, and manufactured under carefully controlled condi-  
tions to provide you with many years of reliable service. Williams Sound warrants the Hearing Helper®  
Personal FM System against defects in materials and workmanship for FIVE (5) years. During the first  
five years from the purchase date, we will promptly repair or replace the Hearing Helper® Personal FM  
System.  
Microphones, earphones, headphones, batteries, chargers, cables, carry cases, and all other accessory  
products carry a 90-day warranty.  
WILLIAMS SOUND HAS NO CONTROL OVER THE CONDITIONS UNDER WHICH THIS PROD-  
UCT IS USED. WILLIAMS SOUND, THEREFORE, DISCLAIMS ALL WARRANTIES NOT SET  
FORTH ABOVE, BOTH EXPRESS AND IMPLIED, WITH RESPECT TO THE Hearing Helper®  
Personal FM System, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MER-  
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. WILLIAMS SOUND SHALL NOT  
BE LIABLE TO ANY PERSON OR ENTITY FOR ANY MEDICAL EXPENSES OR ANY DIRECT,  
INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY ANY USE, DEFECT, FAILURE OR  
MALFUNCTIONING OF THE PRODUCT, WHETHER A CLAIM FOR SUCH DAMAGES IS BASED  
UPON WARRANTY, CONTRACT, TORT OR OTHERWISE, THE SOLE REMEDY FOR ANY  
DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCTS REPLACEMENT OF THE PROD-  
UCT. NO PERSON HAS ANY AUTHORITY TO BIND WILLIAMS SOUND TO ANY REPRESENTA-  
TION OR WARRANTY WITH RESPECT TO THE HEARING HELPER® PERSONAL FM SYSTEM.  
UNAUTHORIZED REPAIRS OR MODIFICATIONS WILL VOID THE WARRANTY.  
The exclusions and limitations set out above are not intended to, and should not be construed so as to con-  
travene mandatory provisions of applicable law. If any part or term of this Disclaimer of Warranty is held  
to be illegal, unenforceable, or in conflict with applicable law by a court of competent jurisdiction, the  
validity of the remaining portions of this Disclaimer of Warranty shall not be affected, and all rights and  
obligations shall be construed and enforced as if this Limited Warranty did not contain the particular part  
or term held to be invalid.  
If you experience difficulty with your system, call Toll-Free for customer Assistance:  
1-800-843-3544  
If it is necessary to return the system for service, your Customer Service Representative will give you a  
Return Authorization Number (RA) and shipping instruction.  
Pack the system carefully and send it to:  
Williams Sound Corp.  
Attn: Repair Dept.  
10321 West 70th Street  
Eden Prairie, MN 55344 USA  
Your warranty becomes effective the date you purchase your system. Your returned warranty card is our  
way of knowing when your warranty begins. It also gives us important information about your system  
including the serial number. This information will help us serve you better in the future. Please take a  
moment to complete and mail the attached card. Thank you.  
17  
 
TECHNICAL SPECIFICATIONS  
FM TRANSMITTER, MODEL PFM T32  
Dimensions:  
Weight:  
3-5/8" L x 2-3/8" W x 7/8" H (92.1 mm x 60.3 mm x 22.2 mm)  
4.4 oz (125 g) with battery  
Color:  
Royal blue, shatter-resistant polypropylene  
Battery Type:  
Two (2) AA 1.5 V non-rechargeable Alkaline batteries (BAT 001), 70 mA nominal current drain, 30  
hours approx. life  
(OR) Two (2) AA 1.5 V NiMH rechargeable batteries (BAT 026), 70 mA nominal current drain, 20  
hours per charge approx., recharges in 14–16 hours, uses CHG 200 or CHG 1600 Charger  
Selectable, 16 channels, 72.1 – 75.9 MHz, internal rotary switch  
.005%, frequency synthesized, crystal reference, PLL  
Wide-band FM, 75 kHz pk, 75 µS pre-emphasis  
Operating Freq’s:  
Stability:  
Modulation:  
RF Output:  
8000 µV/m at 30 m, max., 40 mW typical  
Freq Response:  
Signal-to-Noise Ratio:  
Microphone Gain Control:  
Transmit Antenna:  
Microphone:  
200 to 10 kHz, + 3 dB at 1% max. THD  
55 - 60 dB, with R31 or R32 Receiver  
45 dB maximum, 18 dB minimum range  
Integral with 39" microphone cord  
Electret type, 39" cord, 3.5 mm mono phone plug  
On/Off switch, slide-type; Microphone Mute Switch, slide-type; Compression Selector 1:1 or 2:1 with  
internal selectable jumper  
Controls:  
Mic Connector:  
Compatible Receivers:  
Approvals:  
3.5 mm mono phone jack  
PPA R35, PFM R31, PFM R32  
FCC, Industry Canada, RoHS, WEEE  
Warranty:  
5 years, parts and labor (90 days on accessories)  
Note:  
FCC regulations, section 15.21, requires the user to comply with the rules of transmitter operation. Any changes  
or modifications made by the user not expressly approved for compliance may result in the loss of all privileges  
and authority to operate the equipment.  
RECEIVER, MODELS PFM R31 & PFM R32  
Dimensions and  
Weight:  
3-5/8" L x 2-3/8" W x 7/8" H (92.1 mm x 60.3 mm x 22.2 mm)  
4.6 oz (130 g) with batteries  
Color:  
Battery Type:  
Royal blue, shatter-resistant polypropylene  
Two (2) AA 1.5 V non-rechargeable Alkaline batteries  
(BAT 001), 14 mA nom. current drain, 80 hours approx. life  
(OR)  
Two (2) AA 1.5 V NiMH rechargeable batteries (BAT 026), 14 mA nominal current drain, 50  
hours per charge approx., recharges in 14–16 hours, uses CHG 200 Charger  
Pre-Tuned, Field–tuneable, 72 MHz - 76 MHz.  
Pre-set channels are E (72.9 MHz) and G (75.7 MHz)  
Wide-band, 75 kHz, 75 µS de-emphasis  
120 kHz  
4 µV at 12 dB Sinad with squelch defeated,  
squelches at 10 µV for min. 50 dB S/N ratio  
100 to 10 kHz, + 3 dB  
50 dB at 10 uV  
Integral with earphone cord  
35 mW, max. at 16 Ω  
3.5 mm mono phone jack  
Operating Freq’s:  
FM Deviation:  
AFC Range:  
Sensitivity:  
Freq Response:  
Signal–Noise Ratio:  
Receive Antenna:  
Audio Output:  
Output Connector:  
Squelch:  
Set to turn off audio under weak or no signal condition  
Red LED, turns on in the presence of a carrier  
Carrier Detect Ind:  
Controls:  
Volume:  
rotary/on/off/volume  
Tone:  
3-way slide switch; Lo = flat response (20 Hz),  
Mid = –3 dB at 235 Hz, Hi = –3 dB at 730 Hz  
2-way slide switch; Ch 1 = 72.9 MHz, Ch 2 = 75.7 MHz  
On/off and FM  
Channel:  
Indicators:  
Note:  
Approvals:  
Warranty:  
Specifications are electrical performance  
FCC, WEEE  
5 years, parts and labor (90 days on accessories)  
PFM R31 Receiver Only  
Mic Connector:  
Microphone:  
3.5 mm mono phone jack, supplies positive DC for Williams Sound electret mics  
Plug mount electret, omnidirectional, with windscreen, 3.5mm mono phone plug (MIC 014)  
Rotary control  
Mic Volume:  
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.  
18  
 
ACOUSTIC SPECIFICATIONS  
ANSI 2.44 TEST  
ANSI S3.22–1987 TEST  
FM Response (PFM R31, R32)  
MINIMUM LOW CUT (TONE SET TO LOW)  
Max. SSPL90:  
135.8 dB at 500 Hz  
HF Avg SSPL90:  
HF Avg Full On Gain:  
Reference Test Gain:  
Response Limit:  
127.1 dB  
37.7 dB at 60 dB in  
38.1 dB  
80.1 dB F1=200 Hz, F2=8 kHz  
3.6 % at 500 Hz  
3.9 % at 800 Hz  
2.2 % at 1600 Hz  
Total Harmonic Dist:  
MEDIUM LOW CUT (TONE SET TO MID)  
Max. SSPL90:  
135.5 dB at 600 Hz  
HF Avg SSPL90:  
HF Avg Full On Gain:  
Reference Test Gain:  
Response Limit:  
127.1 dB  
36.8 dB at 60 dB in  
37.3 dB  
79.4 dB F1=200 Hz, F2=8 kHz  
3.4 % at 500 Hz  
3.4 % at 800 Hz  
2.2 % at 1600 Hz  
Total Harmonic Dist:  
FM Response (PFM R31, R32)  
Input:  
80 dB random noise  
MAXIMUM LOW CUT (TONE SET TO HI)  
Device: KEMAR mannequin with BTK 3550 Tester  
Y:  
X:  
Max. SSPL90:  
133.5 dB at 1000 Hz  
80.0 dB 80 db  
100 Hz + 8 OCT LOG  
Main Y: 34.1 dB  
Main X: 4 kHz  
HF Avg SSPL90:  
HF Avg Full On Gain:  
Reference Test Gain:  
Response Limit:  
127.0 dB  
35.4 dB at 60 dB in  
35.8 dB  
78.01 dB F1=200 Hz, F2=8 kHz  
1.1 % at 500 Hz  
2.7 % at 800 Hz  
2.1 % at 1600 Hz  
Total Harmonic Dist:  
Environmental Mic Response  
(PFM R31 Only)  
NO TONE MODIFICATION  
Max. SSPL90:  
134.8 dB at 500 Hz  
HF Avg SSPL90:  
HF Avg Full On Gain:  
Reference Test Gain:  
Response Limit:  
126.4 dB  
40.9 dB at 60 dB in  
40.8 dB  
81.1 dB F1=200 Hz, F2=8 kHz  
1.1 % at 500 Hz  
1.1 % at 800 Hz  
0.3 % at 1600 Hz  
Total Harmonic Dist:  
Environmental Mic Response (PFM R31  
Only)  
Input:  
80 dB random noise  
Device: KEMAR mannequin with BTK 3550 Tester  
Y:  
X:  
80.0 dB 80 db  
100 Hz + 8 OCT LOG  
Main Y: 50.2 dB  
Main X: 4 kHz  
19  
 
© 2007, Williams Sound Corp.  
MAN 072H  
 

West Bend Coffeemaker LARGE CAPACITY COFFEEMAKERS User Manual
Woodstock Drill M1039 User Manual
X10 Wireless Technology Computer Accessories VA13A User Manual
Xerox All in One Printer 4250 XM User Manual
Zanussi Dishwasher 534316 User Manual
Zanussi Freezer ZF36 45 User Manual
Zanussi Range ZAF 42 User Manual
Zanussi Refrigerator ZBA 6160 User Manual
Zanussi Refrigerator ZECL 159 W User Manual
Zanussi Washer ZJ 1217 User Manual