Whirlpool Washer ADP 2315 User Manual

Quick reference guide  
Chart  
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ  
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!  
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING  
ANY BUTTON.  
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES  
AUTOMATICALLY AFTER 30 SECONDS IF ANY CYCLE IS STARTED.  
PROGRAMME  
START/RESUME BUTTON  
BUTTON  
SELECTION BUTTON  
Push “Programs” button  
(repeatedly) until the indicator  
of the required programme  
lights up (see “Table of  
programmes” below).  
Push this button to start the selected programme:  
the indicator lights up and goes off at the end of the  
programme. When the door is opened during a  
washing cycle, the cycle is temporarely paused: the  
Start indicator blinking. To restart the cycle close  
the door and push Start button again.  
Push this button to switch on or switch off the control panel.  
If pressed when a programme is running it cancels  
the programme ongoing.  
If the indicator flashes repeatedly, see page 5 -  
chapter ”What to do if ...”.  
Consumption  
Table of programmes  
Deter-  
gent  
Minutes 1)  
Litres kWh  
Programmes  
Loading instructions  
P
1
2
Crockery to be washed later.  
X
5.0  
0.02  
10  
Pre-Wash  
cold  
Lightly soiled crockery, with no dried-  
on food.  
13.0 0.70  
15.0 1.05  
17.0 1.65  
13.0 1.00  
30  
Quickwash  
40°C  
2)  
Normally soiled crockery.  
X
X
X
150  
145  
130  
50°C  
70°C  
50°C  
3
4
5
Eco  
Recommended programme for heavily  
soiled crockery, especially suitable for  
pans and saucepans.  
Intensive  
Half Load  
Ideal for washing a half load of lightly or  
normally soiled crockery.  
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions  
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible  
with sensor programmes as a result of the appliances automatic calibration system.  
2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for  
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:  
ADP 2315  
5019 396 01824  
GB -1-  
 
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator  
Daily check  
Visual  
indicator  
The rinse aid dosage can be  
adjusted to the detergent used.  
The lower the setting, the less  
rinse aid is dispensed (factory  
setting: position 4).  
Press the button to open the  
cover B. Using a coin or similar  
object, turn the arrow to the  
desired setting. After adjusting  
the rinse aid setting, shut the  
cover again.  
2
If required,  
open the  
cover B  
(press the  
dedicated  
button).  
Add rinse aid  
to the max.  
line ~ 150 ml  
(depending on the model)  
Rinse aid indicator on the control panel  
The indicator lamp lights up when RINSE AID NEEDS  
TO BE ADDED.  
Rinse aid indicator on the dispenser  
dark: OK.  
Check the rinse aid indicator to check the level  
into the dispenser.  
clear: NEEDS TO BE ADDED  
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the  
appliance.  
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty  
drying and a higher rinse aid setting will not improve the situation.  
Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents  
with rinse aid incorporated tend to form excess suds.  
Adding detergent - Use only detergent specifically for dishwashers in accordance with the suppliers recommendations  
Daily use  
Open the cover A  
Insert detergent: Tablet / powder / liquid into the big chamber  
Shut the cover  
(press the dedicated button).  
by pressing dedicated ribs.  
Only fill the  
Use only one tablet per one cycle, only  
placed in detergent dispenser.  
3
detergent dispenser  
prior to starting a  
wash programme.  
All types of tablets can be used, but for  
2 in 1 type adding of salt is mandatory.  
GB -3-  
 
How to load UPPER RACK  
How to load the racks  
How to adjust upper rack height (if available).  
A - Glass-holder for long stem glasses: it can be  
(in some models only)  
C - Cutlery basket: it can be placed in the upper rack  
when the “Half load/Multizone” option is selected.  
adjusted in 2 different positions according glasses shape.  
It could be useful to lift up the upper rack to have  
more space in lower rack or bring it down to load  
long stem glasses.  
- Grasp and take out the two lateral handles (D)  
(they must be on the same level) and lift up or take  
down the upper rack.  
4
B - Adjustable flaps: in horizontal position for cups/  
long utensils, in raised position for plates.  
How to remove the upper rack (if available)  
It could be useful to remove the upper rack to load bulky items in the lower rack.  
- Open the two retainers (E) to take off the upper rack (when the upper rack is in place  
the retainers must always be closed).  
E - CLOSED  
E - OPEN  
How to load LOWER RACK  
(depending on the model)  
F - Foldable plate holders: They can be folded down to load pots  
or  
G - Fixed plate holders  
H - Cutlery basket (or I model)  
J - Grid: Helps to keep the cutlery separate for better washing results.  
H
Arrange crockery so that water does not collect in cavities, ensuring that the spray arms turn freely. Only use dishwasher-proof crockery and dishes. Do not use the dishwasher for washing wooden  
items, aluminium, tin, silver cutlery or decorated crockery (unglazed). In the baskets, dishes (e.g. plates, bowls, pots) must be placed in a correct way to let water flow down!  
5
Switching on the appliance. Press any button to exit Standby and enter programme selection mode.  
GB -4-  
 
Select programme  
Quick, permanent or alternating  
Overview of programmes  
The max. possible number of programmes is illustrated in the chapter “Chart”. The corresponding programmes for your appliance can be found on the panel (page 1).  
6
Choose programme according to the attached table of programmes (page 1).  
Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc.  
Wash cycle  
The dishwasher door must be closed and the water tap open.  
To pause the programme (e.g. if you want to insert an item):  
To Cancel the programme on running:  
To c h a n g e t h e p r o g ramme in progress:  
7
-
Open the door with caution (the programme pauses) and insert  
the item/s,  
-
-
Press the button  
.
-
-
-
-
-
Press the button  
to cancel the programme on running.  
(Water drains for up to 30 seconds then  
the appliance switches off).  
(Water drains for up to 30 seconds then the appliance switches off).  
Press any button to switch on the appliance.  
Select a new programme.  
(beware of HOT steam!).  
-
Close the door and press the START button again to restart the  
cycle (the programme resumes the cycle from where it was  
interrupted).  
Press the START button.  
Switch off the appliance Everything o.k. ...  
Exercise caution when opening the door: beware of hot steam.  
Only press the button  
once to turn the appliance into Standby mode.  
8
All the indicator lamps switch off. Unload the appliance, starting from the lower rack in order to avoid any residual drips of water falling onto crockery below.  
Maintenance and care  
Maintenance and care  
Screw on filter cylinder NOTE MARK!  
9
Filters  
Check and  
clean if  
Unscrew filter  
cylinder, remove it  
and fine sieve...  
Rinse under running  
water ...  
Insert  
necessary  
Rectifying minor faults yourself ...  
Insert and screw on lower and upper arms tightly.  
10  
Spray arms  
Remove  
Clean spray  
Unscrew  
and remove  
lower arm ...  
Unscrew  
and remove  
upper arm ...  
nozzles under  
running water  
(use toothpicks  
if necessary) ...  
blockages/  
deposits.  
GB -5-  
 
What to do if...  
If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem.  
Most faults can be remedied by taking the courses of action, quickly restoring normal appliance operation.  
The appliance...  
...is not working/not start  
Possible causes...  
The appliance must be switched on.  
Solutions...  
-
-
-
-
-
Check the household circuit fuse if there is no power supply.  
The dishwasher door doesnt close.  
“Delayed start” option is ON.  
Water tap closed.  
Check if the dishwashers door is closed.  
Check whether the “Delayed start” option (if available) has been selected. If it has, the appliance will only  
start once the set time has elapsed. If necessary, set the delayed start to “0” (RESET the appliance).  
-
-
-
-
-
The water tap must be open.  
...the indicator lamp  
...the indicator lamp  
blinks 6 times  
The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be  
dirty or clogged.  
Kinked water inlet hose or clogged inlet filters.  
-
-
-
Water pressure too low.  
-
-
-
-
The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).  
The filters must not be dirty or clogged.  
Dirty or clogged filters.  
blinks 6 times and  
Too little water in the dishwashers water system.  
Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack.  
wash programme ended too early (dishes  
are dirty and wet)  
The drain hose must be fitted correctly (for high mounted appliances, leave min. 200-400 mm from the  
lower edge of the appliance) - see Assembly instructions.  
-
Drain hose incorrectly fitted.  
-
-
-
-
High level of foam inside.  
Dirty filters.  
-
-
-
-
Repeat without detergent or wait until foam disappears.  
Clean the filters.  
...the indicator lamp  
blinks 8 times  
Kinked drain hose.  
The drain hose must not be kinked.  
Syphon hose connection closed.  
The closure disk of the syphon hose connection must be removed.  
After taking the above course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated.  
RESET:  
Press the button  
Close the door.  
.
Water drains automatically for up to 30 seconds.  
The appliance is now ready to be restarted.  
Crockery and cutlery...  
...are not perfectly clean/have food residues  
Possible causes...  
Too little space between dishes (incorrect arrangement  
of the concave items in the rack).  
Solutions...  
-
-
-
-
-
-
-
-
-
Arrange crockery so that items do not touch each other. Concave items (e.g. bowls, cups) must be  
arranged facing downwards in the rack.  
If necessary, use more detergent, observing the manufacturers indications as regards dosage. Always store  
detergent in a dry place and do not store it for excessively long periods of time.  
Too little detergent; detergent too old or incorrectly stored.  
For heavily soiled crockery, select a wash programme with a higher temperature (see table of  
programmes - page 1).  
-
-
Temperature not high enough for heavily soiled crockery.  
Loading of the dishwasher using lower and upper rack  
at the same time with “Half load/Multizone” option.  
If you select the “Half load/Multizone” option (if available), remember to load only the upper rack or only  
the lower rack to increase washing power and thus obtain optimum wash results.  
In the event of frequent use of the Eco 50°C programme (if available), from time to time select the  
Intensive 70°C programme (if available).  
-
Frequent use of Eco 50°C.  
The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see page 5,  
“Maintenance and care“).  
-
-
Clogged spray arms, dirty filters or not fitted correctly.  
Spray arms stuck impeded by crockery or cutlery.  
The spray arms must be able to turn freely and must not be impeded by crockery or cutlery.  
GB -6-  
 
What to do if...  
Crockery and cutlery...  
...salt indicator lit  
...have deposits: regeneration salt residue  
Possible causes...  
Use tablets for soft water.  
Solutions...  
-
-
-
-
Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up.  
Water too hard.  
In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water  
hardness”).  
-
-
-
-
Salt reservoir cap open.  
Not enough rinse aid.  
-
-
-
-
Close the salt reservoir cap properly.  
If you use a combined action detergent, try adding more rinse aid.  
Synthetic materials do not dry well; if wet at end of cycle, wipe dry.  
...are not dry  
Plastic containers dry badly.  
Clean dishes left in dishwasher for a long time after end  
of cycle (e.g. when using “Delayed start” option).  
In this situation, the presence of drops of water on dishes and on the sides of the dishwasher is normal.  
Try releasing the door 5 minutes before removing the dishes.  
-
-
-
Incorrect arrangement of the concave items in the rack. - Arrange crockery so that water does not collect in cavities.  
Incorrect dosage the rinse aid.  
Rapid programme selected.  
-
-
Increase the dosage of rinse aid (see page 3, Adding rinse aid”).  
The rapid programme is intended for quickly washing lightly soiled dishes. If used for a full load of medium/  
heavy soiled dishes, the dishes may not dry completely. If so, select a standard-length programme. For best  
results, open the door after the end of the programme and wait 15 minutes before unloading the dishwasher.  
...have discoloured plastic parts  
-
Tomato/Carrot juice.  
-
Tomato sauce, for example, can lead to discolouring of plastic parts. Powder detergent is recommended as  
it allows slightly higher doses to be used for improved whitening. Programmes with higher wash  
temperatures should be used.  
...opaque glasses, etc.  
-
-
Dishes unsuitable for washing in dishwashers (porcelain),  
Usage of incorrect programmes for glasses.  
-
-
Only use dishwasher-proof crockery and dishes.  
...removable deposits on glasses  
Dishes should be put together, to avoid touching each other. Do not put glassware together in baskets.  
Use suitable programme for glass.  
...glasses not sparkling  
-
-
Not conform of glasses to washing in dishwashers  
(porcelain).  
-
Some kinds of glass cannot be washed in the dishwasher.  
...permanent deposits on glasses  
Rainbow effect.  
-
-
-
-
This phenomenon is irreversible. We recommend in future:  
Change the control of system of dosage of softener.  
Be careful – follow recommended detergent dosage.  
For combined action tablets see detergent producers recommendations.  
...tea cups darken and dirt does not  
disappear after washing in dishwasher  
-
-
-
Not known.  
-
-
This phenomenon is inevitable. Theine alters colours permanently.  
...rust marks  
...other marks  
...streaks  
Pre-wash programme not used.  
Rinse aid dosage too low.  
Salty or acidic food residues can cause rust marks even on stainless steel cutlery. To avoid this, always use  
the pre-wash programme if the dishes are to be washed later.  
-
-
In the presence of marks, increase the rinse aid dosage (see page 3, Adding rinse aid”).  
If you use a combined action detergent, possibly add more rinse aid.  
-
-
Rinse aid dosage too high.  
-
-
In the presence of streaks, reduce the rinse aid dosage (see page 3, Adding rinse aid”).  
If you use a combined action detergent try adding more rinse aid.  
...suds  
Unsuitable dosage of detergent/rinse aid.  
-
Only use the amount of detergent/rinse aid required, since excessive amounts can lead to excess suds.  
GB -7-  
 
Disconnect the mains plug  
What to do if...  
If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).  
Before contacting our After-Sales Service, take note of the following:  
- the description of the fault,  
- the appliance type and model,  
- the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:  
Precautions and general recommendations  
1. Packing  
-
-
Before cleaning or carrying out maintenance, disconnect the mains plug and turn off the water tap; also in  
the event of any malfunction.  
Repairs and technical modifications must be carried out exclusively by a qualified technician.  
The packaging materials are 100% recyclable and marked with the recycling symbol  
.
2. Removing the packaging and inspecting the contents  
After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt,  
contact a qualified technician or your local retailer.  
7. Resistance to frost  
If the appliance is placed in surroundings exposed to the risk of frost, it must be drained completely. Turn off  
the water tap, remove the inlet and outlet hoses, and let all the water drain away. Make sure there is at least  
1 kg of dissolved regeneration salt in the salt reservoir, to protect the appliance from temperatures of up to  
-20°C. When the programme resumes, an error message may be indicated (see page 6).  
3. Before using the dishwasher for the first time  
-
-
The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.  
This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may  
leave slight drips/water marks which will disappear with the first wash.  
“the indicator  
least 24 hours.  
blinks 6 times” - the appliance must remain at an ambient temperature of min. 5°C for at  
4. Energy and water savings  
After eliminating these faults, RESET the appliance (see chapter “What to do if...”).  
-
-
-
Do not rinse crockery under running water.  
8. Disposal  
Always fully load the dishwasher before running it or select the “Half load/Multizone” option (if available).  
If ecological energy sources are available such as solar panel heating, heat pumps or centralised heating  
systems, the appliance may be connected to the hot water mains up to a maximum temperature of 60°C.  
Make sure the water inlet hose is of the correct type (“70°C Max” or “90°C Max”).  
-
The appliance is manufactured using recyclable materials. If you decide to scrap the dishwasher, it must be  
disposed of in compliance with local waste disposal regulations. Make it unusable by cutting off the power  
cord. To prevent situations of potential danger to children (e.g. danger of suffocation), break the lock of the  
door so that it can no longer be closed.  
5. Child safety  
-
This appliance is marked according to the European directive 2002/96/CE on Waste Electrical and  
Electronic Equipment (WEEE). By ensuring that this appliance is scrapped suitably, you can help prevent  
potentially damaging consequences for the environment and health. Unsuitable disposal of an appliance of  
-
-
-
Keep the packaging materials out of the reach of children.  
Children must not be allowed to play with the dishwasher.  
Store the detergent, rinse aid and salt out of the reach of children.  
6. Safety warnings  
this type as household waste could have detrimental effects on the environment. The symbol  
on the  
appliance, or on documentation enclosed with the appliance, indicates that this product must not be  
treated as household waste, but must be delivered to the nearest collection centre for the recycling of  
electrical and electronic appliances. Disposal must be carried out in accordance with local environmental  
regulations for waste disposal. For further information on the treatment, recovery and recycling of this  
appliance, contact your competent local authority, the collection service for household waste or the shop  
where you purchased the appliance.  
-
The appliance is not intended for use by children or physically or mentally impaired persons, unless  
adequately supervised by a responsible adult capable of guaranteeing safe use of the appliance.  
Do not operate the appliance in the open air.  
Do not store flammable materials in close proximity to the dishwasher.  
The water in the dishwasher is not potable.  
Do not use solvents inside the dishwasher: risk of explosion!  
Be careful when the door is open: risk of tripping!  
The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest  
objects on the open door or sit or stand on it.  
Sharp items that might cause injury (e.g. knives), must be placed in the cutlery basket with the sharp end  
facing downwards. Long-handled utensils must be arranged horizontally in the upper rack, with the sharp  
end facing away from the front of the appliance.  
-
-
-
-
-
-
EC Declaration of conformity  
This appliance has been designed, constructed and distributed in compliance with the safety requirements of  
EC Directives:  
2006/95/CE, 89/336/CE, 93/68/CE and 2002/95/CE (RoHS Directive).  
-
Loading Capacity: 12 place settings.  
The guarantee is not applicable if faults are caused by incorrect use of the appliance.  
We reserve the right to make technical modifications.  
GB -8-  
 

Weil McLain Boiler HE II Boiler User Manual
Whirlpool Dishwasher DU1055XTSB0 User Manual
Whirlpool Freezer EEV 202X User Manual
White Rodgers Thermostat 1F57 312 User Manual
Xilinx Computer Hardware ML501 User Manual
Zanussi Freezer VFi 42 User Manual
Zanussi Freezer ZCUF 41 User Manual
Zanussi Microwave Oven ZOB 160 User Manual
Zanussi Washer ZWF 1210W User Manual
Zebra Technologies All in One Printer 11280100000 User Manual