Whirlpool Washer 8316473A User Manual

WASHER INSTALLATION INSTRUCTIONS  
Table of Contents  
WASHER SAFETY............................................ 1  
INSTALLATION REQUIREMENTS ................. 2  
Tools and Parts............................................. 2  
Location Requirements................................. 3  
Drain System................................................. 3  
Electrical Requirements ................................ 4  
INSTALLATION INSTRUCTIONS ................... 4  
Before You Start............................................ 4  
Remove Shipping Strap................................ 4  
Connect Drain Hose...................................... 5  
Connect the Inlet Hoses ............................... 5  
Secure the Drain Hose.................................. 6  
Level the Washer........................................... 7  
Complete Installation .................................... 8  
WASHER SAFETY  
Your safety and the safety of others are very important.  
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety  
messages.  
This is the safety alert symbol.  
This symbol alerts you to potential hazards that can kill or hurt you and others.  
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”  
These words mean:  
You can be killed or seriously injured if you don't immediately  
follow instructions.  
DANGER  
You can be killed or seriously injured if you don't  
instructions.  
follow  
WARNING  
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can  
happen if the instructions are not followed.  
8316473A  
 
Location Requirements  
Drain System  
Selecting the proper location for your washer improves  
The washer can be installed using the standpipe drain system  
(floor or wall), the laundry tub drain system, or the floor drain  
system. Select the drain hose installation method you need. See  
Tools and Parts.”  
performance and minimizes noise and possible washer “walk.”  
Your washer can be installed in a basement, laundry room, closet,  
or recessed area. See “Drain System.”  
IMPORTANT: Do not install or store the washer where it will be  
exposed to the weather.  
Standpipe drain system - wall or floor (views A & B)  
Proper installation is your responsibility.  
You will need:  
The standpipe drain requires a minimum diameter standpipe of  
5 cm (2"). The minimum carry-away capacity can be no less than  
64 L (17 gal.) per minute. A 3.2 cm (1¹⁄₄") diameter to 2.5 cm (1")  
diameter standpipe adapter kit is available. See “Tools and  
Parts.”  
I
A water heater set to deliver 49°C (120°F) water to the washer.  
I
An earthed electrical outlet located within 1.2 m (4 ft) of where  
the power cord is attached to the back of the washer. See  
“Electrical Requirements.”  
The top of the standpipe must be at least 99 cm (39") high and no  
higher than 244 cm (96") from the bottom of the washer.  
I
Hot and cold water faucets located within 90 cm (3 ft) of the  
hot and cold water fill valves, and water pressure of 34.5-  
690 kPa (5-100 psi). Washers with triple dispensers require  
138-690 kPa (20-100 psi) for best performance.  
I
I
A level floor with a maximum slope of 2.5 cm (1") under entire  
washer. Installing the washer on carpeting is not  
recommended.  
99 cm  
(39")  
A sturdy floor to support the washer weight (washer, water  
and load) of 143 kg (315 lbs).  
Do not store or operate your washer in temperatures at or below  
0°C (32°F). Some water can remain in the washer and can cause  
damage in low temperatures. See “Washer Care” in the Washer  
User Instructions for winterizing information.  
A
B
Recessed area or closet installation  
Laundry tub drain system (view C)  
The laundry tub needs a minimum 76 L (20 gal.) capacity. The top  
of the laundry tub must be at least 99 cm (39") above the floor and  
no higher than 244 cm (96") from the bottom of the washer.  
The dimensions shown are for the recommended spacing allowed  
(A and B), except the closet door ventilation openings. The  
dimensions shown for the closet door ventilation openings (C) are  
the minimum required.  
Floor drain system (view D)  
The floor drain system requires a siphon break that may be  
7.6 cm  
purchased separately. See “Tools and Parts.”  
35.6 cm  
(3")  
(14" max.)  
310 cm2  
(48 in2.  
)
The siphon break must be a minimum of 71 cm (28") from the  
bottom of the washer. Additional hoses might be needed.  
48.3 cm  
(19")  
155 cm2  
(24 in.2  
)
7.6 cm  
(3")  
71 cm  
99 cm  
(39")  
(28")  
0 cm  
(0")  
0 cm  
(0")  
64.8 cm  
68.6 cm  
(27")  
10.2 cm  
(4")  
2.5 cm  
(1")  
(25¹⁄₂")  
A
C
B
A. Front view  
B. Side view  
C. Closet door with vents  
C
D
I
I
I
I
Additional spacing should be considered for ease of  
installation and servicing.  
Additional clearances may be required for wall, door and floor  
moldings.  
Additional spacing of 2.5 cm (1") on all sides of the washer is  
recommended to reduce noise transfer.  
If a closet door is installed, the minimum air openings in the  
top and bottom of the door are required (C). Louvered doors  
with air openings in the top and bottom are acceptable.  
I
Companion appliance spacing should also be considered.  
3
 
Electrical Requirements  
I
Do not earth to a gas pipe.  
WARNING  
I
Check with a qualified electrician if you are not sure the  
washer is properly earthed.  
I
Do not have a fuse in the neutral or earth circuit.  
EARTHING INSTRUCTIONS  
For an earthed, cord-connected washer:  
This washer must be earthed. In the event of a malfunction  
or breakdown, earthing will reduce the risk of electrical  
shock by providing a path of least resistance for electric  
current. This washer is equipped with a cord having an  
equipment-earthing conductor and an earthing plug. The  
plug must be plugged into an appropriate outlet that is  
properly installed and earthed in accordance with all local  
codes and ordinances.  
Electrical Shock Hazard  
Electrically earth this appliance.  
Do not use an extension cord or an electrical portable  
outlet device.  
Failure to follow these instructions can result in death,  
fire, or electrical shock.  
WARNING: Improper connection of the equipment-  
earthing conductor can result in a risk of electric shock.  
Check with a qualified electrician or serviceman if you are in  
doubt as to whether the appliance is properly earthed.  
I
A 240 volt, 50 Hz., AC only, 8 - 10-amp, fused electrical  
supply is required. A time-delay fuse or circuit breaker is  
recommended. It is recommended that a separate circuit  
serving only this appliance be provided.  
I
I
This washer is equipped with a power supply cord having an  
earthing plug.  
Do not modify the plug provided with the appliance – if it will  
not fit the outlet, have a proper outlet installed by a qualified  
electrician.  
To minimize possible shock hazard, the cord must be plugged  
into a mating, earthing-type outlet, earthed in accordance with  
local codes and ordinances. If a mating outlet is not available,  
it is the personal responsibility and obligation of the customer  
to have the properly earthed outlet installed by a qualified  
electrician.  
For a permanently connected washer:  
This washer must be connected to an earthed metal,  
permanent wiring system, or an equipment earthing  
conductor must be run with the circuit conductors and  
connected to the equipment-earthing terminal or lead on the  
appliance.  
I
If codes permit and a separate earth wire is used, it is  
recommended that a qualified electrician determine that the  
earth path is adequate.  
INSTALLATION INSTRUCTIONS  
3. Locate the yellow shipping strap on the rear of the machine  
near the bottom.  
Before You Start  
WARNING  
Excessive Weight Hazard  
Use two or more people to move and install washer.  
Failure to do so can result in back or other injury.  
NOTE: To avoid floor damage, set the washer onto cardboard  
before moving across floor.  
Remove Shipping Strap  
Removing the shipping strap is necessary for proper operation. If  
the shipping strap is not removed, the washer will make excessive  
noise.  
A
1. Move the washer to within approximately 90 cm (3 ft) of its  
final location.  
A. Yellow shipping strap  
2. The washer must be in the upright position and not tilted  
before removing the shipping strap.  
4
 
4. Pull yellow shipping strap firmly, until both ends are  
Laundry tub drain or standpipe drain  
completely removed from washer.  
Connecting the drain hose form to the corrugated  
drain hose  
C
5. Check that the two (2) cotter pins were removed with the  
shipping strap.  
A
B
A. Place end of drain hose form around hose at drain hose relief.  
Squeeze the latch of the drain hose form until it snaps into place.  
B. Place the other end of the drain hose form around one of the  
remaining drain hose reliefs. Squeeze the latch of the drain hose  
form until it snaps into place.  
C. Drain hose relief  
To keep drain water from going back into the washer:  
I
Do not force excess drain hose into standpipe. Hose should  
be secure but loose enough to provide a gap for air.  
I
Do not lay excess hose on the bottom of the laundry tub.  
Floor drain  
Do not install the drain hose form on to the corrugated drain hose.  
You may need additional parts. See Floor drain under Tools and  
Parts.”  
Connect Drain Hose  
Proper connection of the drain hose protects your floors from  
damage due to water leakage. Read and follow these instructions.  
Connect the Inlet Hoses  
The drain hose is connected to your washer and is stored inside  
the washer cabinet.  
The washer must be connected to the water faucets using the  
new inlet hoses. Do not use old hoses.  
1. Insert new flat washers (supplied) into each end of the inlet  
Remove drain hose from washer cabinet  
hoses. Firmly seat the washers in the couplings.  
Gently pull the corrugated drain hose out of the washer from the  
top of the hose. Continue to pull the hose until the end emerges.  
Do not force excess drain hose back into the rear of the washer.  
A
B
A. Coupling  
B. Washer  
Connect the inlet hoses to the water faucets  
Make sure the washer basket is empty.  
1. Attach the hose labeled hot to the hot water faucet. Screw  
on coupling by hand until it is seated on the washer.  
2. Attach the hose labeled cold to the cold water faucet. Screw  
on coupling by hand until it is seated on the washer.  
5
 
3. Using pliers, tighten the couplings with an additional  
4. Using pliers, tighten the couplings with an additional  
two-thirds turn.  
two-thirds turn.  
NOTE: Do not overtighten or use tape or sealants on the  
valve. Damage to the valves can result.  
Tighten the couplings with an additional two-thirds turn.  
NOTE: Do not overtighten or use tape or sealants on the  
valve. Damage to the valves can result.  
5. Attach the cold water hose to the top inlet valve.  
6. Screw on coupling by hand until it is seated on the washer.  
Clear the water lines  
7. Using pliers, tighten the couplings with an additional  
I
Run water through both faucets and inlet hoses, into a laundry  
tub, drainpipe or bucket, to get rid of particles in the water  
lines that might clog the inlet valve screens.  
two-thirds turn.  
NOTE: Do not overtighten or use tape or sealants on the  
valve. Damage to the valves can result.  
I
Check the temperature of the water to make sure that the hot  
water hose is connected to the hot water faucet and that the  
cold water hose is connected to the cold water faucet.  
Check for leaks  
I
Turn on the water faucets and check for leaks. A small amount  
of water might enter the washer. You will drain this later.  
NOTE: Replace inlet hoses after 5 years of use to reduce the  
risk of hose failure. Record hose installation or replacement  
dates for future reference.  
I
If you connect only one water hose, you must cap off the  
remaining water inlet port.  
I
Periodically inspect and replace hoses if bulges, kinks,  
cuts, wear, or leaks are found.  
Secure the Drain Hose  
1. Remove the shipping strap from the power cord. Drape the  
power cord over the console.  
2. Remove any cardboard used to move washer.  
Connect the inlet hoses to the washer  
A
B
Beaded tie strap  
3. Wrap the drain hose to the laundry tub leg or drain standpipe  
with the beaded tie strap. Push fastener into the nearest hole  
in the beaded tie strap. See view A or B.  
A. Cold water inlet valve  
B. Hot water inlet valve  
1. Attach the hot water hose to the bottom inlet valve.  
2. Attaching the hot water coupling first makes it easier to  
tighten connection with pliers.  
3. Screw on coupling by hand until it is seated on the washer.  
A
B
C
If the washer faucets and the drain standpipe are recessed,  
put the formed end of the drain hose into the standpipe.  
Tightly wrap the tie strap around the water inlet hoses and the  
drain hose. See view C.  
6
 
Level the Washer  
Properly leveling your washer avoids excessive noise and vibration.  
Install the Front Leveling Feet  
Steps in Final Location  
1. Prop up the front of the washer about 10.2 cm (4") with a  
wood block or similar object. The block needs to support the  
weight of the washer.  
1. Slide the washer to its final location.  
2. Tilt the washer forward until the rear of the washer is at least  
10.2 cm (4") off the floor. You may hear the self-adjusting rear  
feet click into place. Lower the washer to the floor.  
10.2 cm  
(4")  
10.2 cm  
(4")  
A
A
A. Self-adjusting feet  
A. Threaded holes for feet  
3. Check the levelness of the washer by placing a level on the  
top edges of the washer, first side to side, then front to back.  
2. Screw the locknut onto each foot to within 2.5 cm (1") of the  
foot base.  
2.5 cm  
(1")  
4. If the washer is not level, move the washer out slightly, tip  
back, prop up the front of the washer with the wood block  
and adjust the feet up or down as necessary by twisting the  
feet. Turn the feet clockwise to raise the washer or  
counterclockwise to lower the washer. Repeat steps  
1 through 4 until washer is level.  
3. Screw the feet into the threaded holes at the front corner of  
the washer until the nuts touch the washer. Twist the feet to  
install.  
NOTE: Do not tighten the nuts until the washer is level.  
4. Tilt the washer back and remove the wood block. Gently lower  
5. After the washer is in its final location and level, use a 14 mm  
or ⁹⁄₁₆" open-end wrench to turn the nuts counterclockwise on  
the feet tightly against the washer cabinet.  
the washer to the floor.  
IMPORTANT: If the nuts are not tight against the washer  
cabinet, the washer may vibrate.  
7
 
Complete Installation  
1. Check the electrical requirements. Be sure that you have the  
7. Check for leaks around faucets and inlet hoses.  
correct electrical supply and the recommended earthing  
method. See Electrical Requirements.”  
WARNING  
2. Check that all parts are now installed. If there is an extra part,  
go back through the steps to see which step was skipped.  
3. Check that you have all of your tools.  
4. Check that the yellow shipping strap was completely removed  
from the lower back of the washer.  
5. Dispose of or recycle all packaging materials.  
6. Check that the water faucets are on.  
Electrical Shock Hazard  
Electrically earth this appliance.  
Do not use an extension cord or an electrical portable  
outlet device.  
Failure to follow these instructions can result in death,  
fire, or electrical shock.  
8. Plug into an earthed outlet.  
9. Remove the protective film on the console and any tape  
remaining on the washer.  
10. Read Washer Usein the Washer User Instructions.  
11. To test and to clean your washer, measure ¹ꢀ₂ of the normal  
recommended amount of powdered or liquid detergent and  
pour it into the washer basket or detergent dispenser (on  
some models). Close the lid. Select any cycle, and then pull  
the cycle control knob out to start the washer. Allow it to  
complete one whole cycle.  
8316473A  
9/05  
Printed in U.S.A.  
© 2005 Whirlpool Corporation.  
Benton Harbor, Michigan 49022  
 

Weider Home Gym 831156090 User Manual
Weider Home Gym WESY68633 User Manual
Whirlpool Freezer EVZOON User Manual
Whirlpool Washer Dryer LA609OXS User Manual
White Rodgers Furnace 37 5234E User Manual
Xantrex Technology Power Supply XPF 60 20 User Manual
Xerox Copier C2128 User Manual
Zanussi Boiler SPE2015CC User Manual
Zanussi Ice Maker 730160 User Manual
Zanussi Refrigerator RCSF16G1X User Manual