UB-R02 User’s Manual
410462701
Copyright © Seiko Epson Corporation 2004
Printed in China 2004.01
Introduction
The UB-R02 is an interface board on which is installed an IEEE 802.11b Radio
Frequency (RF) module for EPSON® TM printers.
This manual provides instructions, including a simple setup for operators of
POS systems in which the UB-R02 is installed so that the operators can use the
UB-R02 safely and correctly.
Key to Symbol
The symbol in this manual is identified by its level of importance, as defined
below. Read the following carefully before handling the product.
Note:
Notes have important information and useful tips on the operation of your equipment.
Features and Functions
❏
❏
64/128-bit WEP
Protocols: TCP, UDP, ICMP, IP, LP/LPR (for APD), TCP socket port (for
OPOS)
❏
❏
Transfer rate: up to 11 Mbps, depending on operating environment
OPOS, APD support
Part Names
The following view shows the part names of the UB-R02.
Drawer kick-out
connector
Push button
Power supply
connector
Note: This photograph shows the TM-T88III printer with the UB-R02 installed.
DIP Switches
When using this interface board, the interface of the TM printer must be
selected as “parallel” with the appropriate settings. Set the reset signal for pin
31 to “enable,” if you are using a TM printer that has this setting. Refer to the
manual for each TM printer for details.
1
EMC Standards Applied
Product Name: UB-R02
Model Name: M195A
The following standards are applied only to the interface boards that are so labeled. (EMC is tested using the EPSON
power supplies and TM series printers.)
Europe:
North America: EMI:FCC/ICES-003 Class A
Oceania: EMC:AS/NZS 3548, CISPR22 Class B
CE marking
WARNING
You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation could void your
authority to operate the equipment.
CE Marking
The printer conforms to the following Directives and Norms:
Directive 89/336/EECEN 55022 Class B
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-11
The printers in which this board is installed do not conform to the following:
Directive 90/384/EEC
EN 45501
FCC Compliance Statement For American Users
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
For Canadian Users
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
RF Module
This equipment contains the following wireless module.
Manufacturer: TOYOTA INDUTRIES CORPORATION
Model Name: 6180210
Product Name: WIRELESS LAN CF-CARD
This device complies with Part 15 of the FCC Rules and RSS-210 of the IC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
USA
This device conforms to Part 15 of the FCC rules.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
3
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Canada
This device conforms to IC, Low Power License-Exempt Radio Communication Devices (RSS-210).
The information such as Certification No., Model Name, and Manufacturer Name are described on the surface of the
module.
Europe
Hereby, TOYOTA INDUSTRIES CORPORATION declares that this 6180210 is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC and 89/336/EEC.
France
In France, using the UB-R02 outdoors is prohibited.
Italy
In Italy, if used outside of own premises, general authorization is required.
Australia/New Zealand
This equipment contains the following wireless module.
Manufacturer: TOYOTA INDUTRIES CORPORATION
Model Name: 6180210
Product Name: WIRELESS LAN CF-CARD
ACN: 104644 635
The UB-R02 can be used only in the countries listed below:
Austria, Belgium, Germany, Luxembourg, Netherlands, Switzerland, France,
Italy, Greece, Spain, Portugal, Denmark, Finland, Ireland, Sweden, UK, USA,
Canada, Australia, New Zealand, Czech Republic, Estonia, Hungary,
Lithuania, Latvia, Poland, Slovenia, Slovak Republic, and Norway.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written
permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information
contained herein. While every precaution has been taken in the preparation of this book, Seiko Epson Corporation
assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of
this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or
any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by
Seiko Epson Corporation.
EPSON is a registered trademark of Seiko Epson Corporation.
Windows is a registered trademark of Microsoft Corporation, USA.
General Notice: Other product and company names used herein are for identification purposes only and may be
trademarks of their respective companies.
Notice: The contents of this manual are subject to change without notice. Please contact us for the latest information.
Printed on Recycled Paper
4
|