Sanyo Projector Accessories AH 23511 User Guide

LCD Projector  
Lens Replacement Procedure  
Model Number  
LNS-T10/LNS-W10/LNS-T11/LNS-W11  
AH-23541/AH-23511/AH-23661/AH-23631  
Notes on Lens Replacement  
Lens replacement should be performed by the qualified service  
personnel.  
It should be followed by this procedure precisely.  
Before an attempt to replace the lens, confirm the model number  
(both the LCD projector and the lens) and prepare the proper lens.  
Lens installation is different in cabinet design (Type A and B).  
Before installation the lens, check cabinet design should be made.  
The lens cover is on the lens for protection. Be sure to remove the  
lens cover before installation.  
When installing or removing the lens, be careful not to stain,  
scratch or damage the lens.  
If you have any questions, contact the dealers.  
Parts List  
Following parts are contained in the packing.  
G LENS  
G LIGHT-BLOCK SHEET (Spare)  
{Except LNS-W11 (AH-23631)}  
1 piece  
1 piece (Part No. 910 322 9677)  
Notes on Lens Replacement  
After the lens replacement (before attaching the top cabinet), check the following  
things.  
1. Check the lens is properly installed.  
2. Check no wiring is tangled on the gear of the lens motor or other mechanical  
parts.  
3. Check no parts is missing, or no mounting part is lost.  
1AA6P1P5412-- (IFEK-EI)  
Printed in Japan  
 
(For B type Cabinet)  
Lens Replacement Procedure  
Perform the steps 1-6 for lens replacement.  
First set the lens at the lowest position with lens shift adjustment.  
Remove the Lens Cover and the Top Cabinet  
1
1. Turn the Lens Cover counter-clockwise and pull it  
toward front to remove the Lens Cover.  
2. Remove the two screws (SCREW "A") and remove  
the Top Cabinet.  
TOP CABINET  
SCREW "A"  
Fig-1-1  
LENS COVER  
1. Pull Lens Cover toward front and remove it.  
2. Remove the two screws (SCREW "A") and remove  
the Top Cabinet.  
SCREW "A"  
TOP CABINET  
Fig-1-2  
LENS COVER  
Remove the Light-Block Sheet Base  
Slide the Light-Block Sheet Base upward to remove it.  
2
LIGHT-BLOCK  
SHEET BASE  
Fig-2  
-3-  
 
3
Remove the Lens  
Push the Lens Lock Lever and turn the lens counter-  
clockwise (1/4 turn) and then take it out.  
Be careful not to drop the lens.  
LENS LOCK  
LEVER  
Fig-3  
Mount the Lens  
4
1. Remove the protective caps (front and back) on the  
lens.  
2. Put the Light-Block Sheet through the lens.  
{When LNS-W11 (AH-23631) is installed, the Light  
Block Sheet is unnecessary.}  
3. Insert the lens into the Lens Bracket of the projector  
as matching the red mark on the lens to that on the  
Lens Bracket.  
4. Turn the lens clockwise until the lens is locked with  
Lens Lock Lever.  
LENS  
BRACKET  
Insert the lens into the Lens Bracket  
as matching these marks.  
Fig-4  
-4-  
 
Mount the Light-Block Sheet Base  
5
Mount the Light-Block Sheet Base.  
LIGHT-BLOCK  
SHEET BASE  
HOOKS  
LIGHT-BLOCK  
SHEET  
Light-Block Sheet should be  
located under the hooks.  
Fig-5  
HOOKS  
Mount the Top Cabinet and the Lens Cover  
For the Cabinet Fig. 6-1  
6
1. Mount the Top Cabinet with 2 screws.  
2. Mount the Lens Cover.  
Position the mark "UP" of the Lens Cover on top and  
push into the cabinet. Turn the Lens Cover  
clockwise until it is securely locked.  
{When LNS-W11 (AH-23631) is installed, the Lens  
Cover is unnecessary.}  
UP  
For the Cabinet Fig. 6-2  
1. Mount the top cabinet with 2 screws.  
2. Push into the Lens Cover to the Top Cabinet.  
Fig-6-1  
Confirm the top and bottom of the lens cover.  
The part circled in Fig-6-2 should be fitted.  
{When LNS-W11 (AH-23631) is installed, the Lens  
Cover is unnecessary.}  
Turn the projector on and check Lens shift, Zoom and  
Focus is operating properly.  
If Light-Block Sheet interfere with those operations,  
check if the Light-Block Sheet is set properly.  
LNS-W11 (AH-23631) cannot adjust the Zoom and  
Focus at the Remote control or the projector.  
Fig-6-2  
-5-  
 
{For LNS-W11 (AH-23631)}  
Focus Adjustment  
Set up the projector in the place where it is to be used, turn on the power and project a picture.  
Adjust the position of the projector to suit the projection position.  
1. Turn the focus ring to adjust the focus at the center of the screen. The focus at the edges of the  
screen may not be as sharp as at the center of the screen.  
2. If the focus cannot be set correctly at the center of the screen, it will be necessary to move the  
lens unit forward or back relative to the flange in order to adjust the back focus. Carry out this  
adjustment according to the procedure given below.  
a. Turn the fixing roulette about 1/4 of a turn counterclockwise to release it. The roulette can be  
released more easily if you place the tip of your finger on the pin where the roulette is.  
b. If the current focal point is somewhere forward of the screen, turn the focus ring clockwise;  
if the focal point is somewhere behind the screen, turn the focus ring counterclockwise, and  
then turn the precision lens unit (the focus ring and the fixing roulette) 5 degrees.  
c. Turn the focus ring to adjust the focus at the center of the screen. (Be careful not to move the  
whole of the lens unit at this time.)  
d. Repeat steps b and c until correct focus is obtained.  
Note: If the lens unit is difficult to move when carrying out the above procedure, turn the fixing  
roulette counterclockwise a further 1/4 of a turn.  
e. Once the above adjustment is complete and the picture is in focus, turn the fixing roulette  
clockwise until it is tightened securely. Do this carefully, otherwise the focus may become  
disrupted. If the roulette is not tightened securely, it may become difficult to remove the lens  
during lens replacement.  
3. If the focus cannot be correctly adjusted even after the above procedure has been carried out,  
try adjusting by carrying out the procedure given below.  
a. Set the distance between the screen and the edge of the lens to 0.77 m and project a picture.  
b. Turn the roulette counterclockwise to release it.  
c. Turn the focus ring counterclockwise as far as it will go, and then move the lens unit (the  
focus ring and the fixing roulette) to adjust the focus at the center of the screen.  
d. Check that the focus at the center of the screen is correct, and then turn the fixing roulette  
clockwise until it is tightened securely. Check that the focus ring is still turned  
counterclockwise as far as it will go at this time.  
e. Return the projector to its original setup location and repeat steps 1 and 2 to adjust the focus.  
PIN  
FOCUS RING  
FLANGE  
ROULETTE  
NOTE: Please remove 3 pins when you install it in the cabinet of B type.  
-6-  
 

PYLE Audio Speaker System PLMRKT4A User Guide
Radio Shack Caller ID Box CID 940 User Guide
RedMax Trimmer CHT2301 User Guide
ReliOn Humidifier Model H 0565 0 User Guide
Rosewill Computer Drive RC218 User Guide
Rosewill Computer Monitor R910E User Guide
Samsung Computer Monitor 1100PPLUS User Guide
Samsung Home Security System P4042 User Guide
Samsung MP3 Player DVD V2500 User Guide
Seiko Instruments Printer DPU S445 User Guide