INSTRUCTION MANUAL
LCE-24C100F(K)
LCE-24C100F(N)
LCE-24C100F(R)
LCE-24C100F(S)
LED LCD TV
SAFETY INSTRUCTIONS
Before operating this LCD TV, read this manual thoroughly and operate the LCD TV properly. This LCD TV provides many convenient
features and functions. Operating the LCD TV properly enables you to manage those features and maintains it in better condition for a
considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
If your LCD TV seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the
“Troubleshooting” section on page 17 of this booklet. If the problem still persists, contact the dealer where you purchased the LCD TV or the
service center.
Safety Precaution
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
WARNING :
● Install the LCD TV in a proper position. If not, it may result in a fire hazard.
● Provide appropriate space on the top, sides and rear of the LCD TV cabinet for allowing
air circulation and cooling the LCD TV. Minimum clearance must be maintained. If the
LCD TV is to be built into a compartment or similarly enclosed, the minimum distances
must be maintained. Do not cover the ventilation slot on the LCD TV. Heat build-up can
reduce the service life of your LCD TV, and can also be dangerous.
● If the LCD TV is not to be used for an extended time, unplug the LCD TV from the power
outlet.
SIDE and TOP
10 cm
REAR
6 cm
10 cm
10 cm
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
Caution In Installing
● Handle the
carefully when installing it and do not drop.
LCD TV
● Locate set away from heat, excessive dust, and direct sunlight.
● For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. Failure to follow correct mounting
procedures could result in damage to the equipment or injury to the installer.
NOTE :
When LCD TV is not used for a long period of time, unlighted dots may be observed. This is caused by characteristic of the LCD TV. If this
occurs, turn the LCD TV on and leave it on about 1 hour. These dots will gradually disappear.
T H I S S Y M B O L I N D I C AT E S T H AT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DISPOSAL PRECAUTIONS
DANGEROUS VOLTAGE CONSTITUTING
R I S K O F E L E C T R I C S H O C K
A
I S P R E S E N T W I T H I N T H I S U N I T.
CONTAINS MERCURY
LAMPS, DISPOSE OF
PROPERLY
THIS SYMBOL INDICATES THAT THERE
A R E I M P O RTA N T O P E R AT I N G A N D
MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
All the safety and operating instructions should be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this LCD TV from AC power supply before cleaning. Do not use
liquid or aerosol cleaners. Use a damp cloth for cleaning. Follow all warnings and instructions marked on the LCD TV. For added protection to
the LCD TV during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and power line surges.
Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may cause hazards.
Do not place this LCD TV on an unstable cart, stand, or table. The LCD TV may fall, causing serious injury to a child or adult,
and serious damage to the LCD TV. Use only with a cart or stand recommended by the manufacturer, or sold with the LCD
TV. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the
manufacturers.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause
the appliance and cart combination to overturn.
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and
to protect it from overheating. The openings should never be covered with cloth or other materials, and the bottom opening should not
be blocked by placing the LCD TV on a rug, or other similar surface. This LCD TV should never be placed near or over a radiator or heat
register. This LCD TV should not be placed in a built-in installation such as a book case unless proper ventilation is provided. Never push
objects of any kind into this LCD TV through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the LCD TV. Do not place items such as vases containing liquid on top of the LCD TV.
Do not install the LCD TV near the ventilation duct of air-conditioning equipment.
This LCD TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power
supplied, consult your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord.
Do not locate this LCD TV where the cord may be damaged by persons walking on it.
Do not attempt to service this LCD TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
Unplug this LCD TV from wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilLCD into the LCD TV.
c. If the LCD TV has been exposed to rain or water.
d. If the LCD TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the
operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified
technician to restore the LCD TV to normal operation.
e. If the LCD TV has been dropped or the cabinet has been damaged.
f. When the LCD TV exhibits a distinct change in performance-this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the
same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this LCD TV, ask the service technician to perform routine safety checks to determine that the
LCD TV is in safe operating condition.
3
TABLE
FEATURE AND DESIGN.......................................4
PREPARATION........................................5
PICTURE MODE
SPORTS MODE
OFF TIMER
WIDE
10
10
10
10
PART NAMES AND FUNCTIONS
5
CONNECTING LCD TV......................6
INSTALLING & UNINSTALLING
MENU OPERATION............................................... 11
STAND BASE
6
6
7
CHANNEL
PICTURE
SOUND
11-12
12
CONNECTING AC POWER CORD
CONNECTING A COMPUTER
CONNECTING VIDEO EQUIPMENT &
AERIAL
13
TIMER
13
7
OSD
13
BASIC OPERATION.............................................8
SETUP
14
OPERATION OF REMOTE CONTROL
REMOTE CONTROL BATTERIES
INSTALLATION
8
SETUP (PC MODE)
DEALER MODE
14-15
15-16
8
8
APPENDIX..............................................................16
CLEANING LCD TV 16
FUNCTION OF PRODUCT SAFETY FEATURE 16
TURNING ON/OFF LCD TV
PLUG & PLAY
9
SELECTING INPUT SOURCE
CHANNEL RECALL
CHANNEL SELECTION
INFO
9
TROUBLESHOOTING
17
18
19
9
9
TECHNICAL SPECIFICATIONS
SIGNAL MODE COLUMN (Recommended)
10
10
10
10
10
VOLUME CONTROL
MUTE
STEREO/MONO
SOUND MODE
is registered trademarks of HDMI Licensing, LLC.
TRADEMARKS
●
●
●
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.
Feature and Design
¡ Picture
●
SHOP Mode
Picture mode will be Dynamic and ECO mode
will be OFF in SHOP MODE.
●
High Definition LCD with LED Backlight Panel
1920 x 1080 pixel FHD LCD LED Backlight Panel with high
contrast ratio and wide viewing angle.
¡ Compatibilty
●
VIZON Engine
●
Full Multi System
VIZON Engine, SANYO High Quality Image Processing
Technology reproduces clear, dynamic, natural and realistic
picture along with FHD LCD Panel Technology.
PAL, SECAM, NTSC, NTSC 4.43 system can be connected.
HD-Ready
1080p, 1080i, 720, Full High Definition signals are receivable.
●
●
Dynamic AI
●
HDMI
HDMI provides complete transmission of digital
image and sound signals without any quality deterioration.
DVI can be connected to HDMI.
PC Input
Personal Computer/Laptop can be connected with automatic
resolution adjustment.
The AI (Automatic Image Control) circuit compensates picture
contrast and brightness level dynamically and reproduces bright
and high-contrast picture.
●
●
¡ Sound
●
NICAM/A2 Stereo
It's the Stereo Sound PAL Color TV Broadcasting System upgrading
mono-sound TV service to stereo or dual-language sound.
Terminals
HDMI for BluRay Player etc.
D-SUB 15-pin for PC input etc.
Component Video for DVD
Video for VCR/DVD
●
Bass Expander
Bass Expander reinforces bass effect to improve overall sound quality.
¡ Feature
¡ Others
●
Sports Mode
Just by pressing the button, sports mode optimizes picture and sound
settings suitable for each sports program.
ƒ OFF
Normal setting.
ƒ Football
Use to watch football program, golf program or etc.
ƒ Winter Sport
Suitable setting for skiing program or etc.
ƒ Marine Sport
●
Wall Mounting
It's designed for VESA Standard (200 x 200) wall hanging bracket.
●
Light Commercial Mode
By entering Dealer mode, Volume Lock, Tuning Lock, Start Mode,
OSD, RC, AC Power Mode, Start Volume Level, Music Mode and
Reset can be selected.
Convenient for placing in Hotel, Hospital, School, Store, Bank etc.
Suitable setting for swimming, diving program or etc.
ƒ Indoor Sport
Suitable setting for basketball, badminton program or etc.
4
PREPARATION
PART NAMES AND FUNCTIONS
FRONT
Panel
Side Control
Infrared
Remote
Receiver
Power/Timer
Indicator
CARE FOR USING LCD TV
● Do not bump or scratch the panel surface as this causes flaws on the surface of the screen.
● There may be some tiny black points and/or bright points on the SCREEN. These points are normal.
SIDE CONTROL
POWER ON/ OFF button
-Used to turn the LCD TV on or off.
MENU button
-Open or close the On-Screen Menu.
INPUT MODE button
Used to select input source: TV/AV1/ AV2(DVD) /HDMI(DVI)/PC.
-Used to confirm the selected item on On-Screen Menu.
VOLUME buttons
Each button on the control
panel has the same function
with its counterpart on the
remote control.
-
(+/-)
-Used to adjust the volume.
-Used to adjust the value of the selected item on On-Screen Menu.
-Used to execute the selected item on On-Screen Menu.
(
) buttons
CHANNEL UP/DOWN ▲/▼
-Used to Change channels.
-Used to select items on On-Screen Menu.
BACK TERMINAL
HDMI Input Terminal
Connect video and audio outputs
from video equipment.
PC Input Terminals
Connect computer outputs to these
terminals.
● RGB (D-SUB)
● Audio (L/R)
AV1 Terminals
Connect video and audio outputs from
video equipment.
● Video (RCA type)
AV2 Terminals
Connect video and audio outputs
from video equipment.
● DVD component (RCA type)
● Audio L and R (RCA type)
● Audio L and R (RCA type)
Monitor Output Terminals
Aerial Jack
Connect a television, video recorder or
external audio amplifier to these jacks.
● Video (RCA type)
Connect the cable with a plug from
aerial jack to the aerial socket on
the cabinet back.
● Audio L and R (RCA type)
5
CONNECTING LCD TV
INSTALLING & UNINSTALLING STAND BASE
Please according to the following procedure to install stand.
Be careful of the panel. Suggest to put down the panel side on the cushion or other soft material before installing
the stand.
1
To align the corresponding pilot holes and fix the stand by screws.
Screws (M4x8) for LCE-24C100F(K)/(N)/(R)/(S): 2 pcs
2
Installing of stand is completed.
Screw M4 X 8 :
3
Model LCE-24C100F(K)/(N)/(R)/(S):
Screw : M4 X 8
Screw : M4 X 8
CAUTION IN INSTALLING & UNINSTALLING STAND BASE
Through in installing or uninstalling work, handling with more than two people is recommended.
When holding (moving or lifting) the LCD Display, hold the display's body. Do not handle the LCD TV by holding the attached accessory parts,
otherwise it may result in damage.
●
●
●
Before installing or uninstalling, provide a desk (or a part of it) which is strong enough to support the weight of the LCD TV and this stand. The
desk must be larger than the LCD Display screen size. The desk's surface must be flat and maintained with soft material (such as a blanket) for
protecting the screen surface.
●
●
Before putting the LCD Display on the desk, make sure there is no object on it. Leaving any object under the screen may cause damage on the
screen.
The LCD TV with this stand should be installed or uninstalled on flat and level place. Do not place on such as a non flat, unlevel or unstable cart or
stand. The display may fall, causing not only serious damage to the products but serious injury to a person.
SAFETY NOTE
For correct installing, mounting and uninstalling LCD TV Stand, it is strongly recommended to use a trained, authorized dealer. Failure to follow
correct procedures could result in damage to the equipment or injury to the installer.
CONNECTING AC POWER CORD
This LCD TV uses nominal input voltages of 110-240V AC. This LCD TV
automatically selects the correct input voltage. It is designed to work with single-
phase power systems. To reduce risk of electrical shock, do not plug into any
other type of power system. Consult your authorized dealer or service station if
you are not sure of the type of power being supplied.
Connect the LCD TV with all peripheral equipment before turning the LCD TV on.
Note:
AC Power Cord types vary between countries.
CAUTION
For safety, unplug AC power cord when the LCD
TV is not in use.
AC POWER CORD
To the AC Outlet (110 - 240V AC).
Pulls the AC power cord out from
the LCD TV. The AC outlet must be
near this equipment and must be
easily accessible.
6
CONNECTING LCD TV
CONNECTING A COMPUTER
Cables used for connection (These cables are not
supplied with this LCD TV.)
● PC/VGA Cable (D-SUB 15pin)
● HDMI Cable: HDMI Input
● MAC Adapter (in the case of connecting Macintosh
computer)
NOTE:
When connecting the cables, AC Power Cords
of both LCD TV and external equipment should
be disconnected from AC outlet. Turn LCD
TV and peripheral equipment on before your
computer is switched on.
● Audio Cable [Mini Plug (L/R)]
Desktop
type
Laptop
type
IBM-compatible
computers
Monitor Output
PC Input
or Macintosh
computers
MAC
Adapter
(VGA / SVGA /
XGA )
HDMI Output
HDMI Input
Note:
1. You can connect the DVI source to HDMI input
terminal by using the DVI to HDMI converter.
2. When inputting 1080p signal to HDMI terminal,
please use High Speed HDMI Cables to avoid
picture/ sound noise and no picture/sound.
3. When connect to HDMI Input terminal, it needs few
seconds to display picture.
Audio Output
(stereo)
Audio Input
(stereo)
CONNECTING VIDEO EQUIPMENT & AERIAL
Component Video Source
(example)
Cables used for connection (These cables are not supplied with this LCD TV.)
● Video Cable(RCA X1), Audio Cable (RCA X2) : Video 1 or Video 2
● Video Cable(RCA X3), Audio Cable (RCA X2) : DVD (Component Video)
● Video Cable(RCA X1), Audio Cable (RCA X2) : Monitor Output
● HDMI Cable: HDMI Input
DVD video equipment.
(such as DVD player or high-definition
TV source)
DVD Player
Video 1 signal is output from AV1 terminals;
Video 2 signal is output from Y/L/R terminals of AV2.
R
L
CR/PR,CB/PB, Y
NOTE : When connecting the cable, AC Power Cords
of both LCD TV and external equipment should
be disconnected from AC outlet.
DVD
(RCA X 3)
Audio cable
(RCA X 2)
MONITOR OUT
Note:
Video (RCA) output is for
TV, or AV only.
Audio Amplifier
Composite Video
and Audio Output
Video cable
(RCA x1)
Audio
Speaker
(stereo)
Outdoor Aerial
Audio cable
(RCA x 2)
External
monitor
External Audio
Equipment
Video and Audio
cable (RCA x 3)
Aerial Cable
Video Source (example)
Video Disc
Player
Video Cassette
Recorder
7
BASIC OPERATION
OPERATION OF REMOTE CONTROL
POWER ON/OFF button
SOUND button
INPUT button
INFO / VA·B button
PICTURE button
WIDE button
SPORTS button
TIMER button
NUMERIC buttons
CHANNEL UP/DOWN buttons
CHANNEL RECALL button
VOLUME +/- buttons
MUTE button
BACK button
DIGIT button
MENU button
ENTER button
▼ ◄
/ /►buttons
POINT ▲/
REMOTE CONTROL BATTERIES INSTALLATION
Remove the battery compartment cover.
1
Insert two size AA batteries (1.5V) according to "+" and "-" polarity markings inside
the battery compartment.
2
Close the battery compartment cover.
3
Note:
Do not expose batteries (battery pack or batteries installed) to excessive heat such
as sunshine, fire or the like.
TURNING ON / OFF LCD TV
SIDE CONTROL
Complete the peripheral connections before turning on LCD TV. (Please refer to "CONNECTING
1
LCD TV".)
Connect LCD TV's AC Power Cord into an AC outlet.
2
3
POWER ON/ OFF
button
Press POWER ON/OFF button on Side Controls of LCD TV or on
Remote Control to turn it ON. The POWER indicator will light up
(green). Press POWER ON/OFF button again to shift it to stand-by
status, the POWER indicator will become red.
REMOTE CONTROL
NO SIGNAL SHUT OFF
This TV set incorporates the NO SIGNAL SHUT OFF function.
If no signal is input in TV mode, "OFF 00:10" will display for about 10 minutes and TV will be
turned off automatically.
POWER ON/
OFF button
8
BASIC OPERATION
PLUG & PLAY
By PLUG & PLAY, when the TV reset and powered on for the first time, it will automatically
search and preset all the receivable TV programs.
I AM SEARCHING ALL PROGRAMMES
PLEASE WAIT!
Plug the power, connect the antenna, and press Main Power ON/OFF button, the TV set will
1
1
automatically search the programs.
MENU
:
CANCEL
After programs searching, SHOP MODE menu will appear. Press POINT ◄► buttons to select
2
and press ENTER button for SHOP MODE or HOME MODE. Then the pop up menu disappears.
Auto searching completed and message "AUTO SET-UP COMPLETED HAPPY VIEWING!"
appears. About 5 seconds later, the TV set will automatically return to programme position “1”.
3
PLEASE SELECT AND PRESS ENTER BUTTON
HOME MODE SHOP MODE
Message "NO STATION PLEASE CONNECT ANTENNA PLUG!" will appear if there is no TV stations
are searched after automatically programs searching.(see Figure A.) Then SHOP MODE menu
appears, the same operations as step 2 above will be excuted and returns to normal TV picture.
Press MENU button while searching programs, message "PLEASE SELECT AND PRESS ENTER
BUTTON" appears (see Figure B), press POINT◄► buttons to select "TEMPORAL CANCEL" or
"PERMANENT CANCEL".
:
SELECT
:
ENTER
ENTER
AUTO SET-UP COMPLETED
HAPPY VIEWING!
TEMPORAL CANCEL to cancel temporary PLUG & PLAY function. The PLUG & PLAY function is
actived only in TV mode while turning on the LCD TV.
Figure A.
PERMANENT CANCEL to cancel permanetly PLUG & PLAY function. When turn on television the
PLUG & PLAY is not actived. Press ENTER button to enter SHOP MODE menu. the same operations
as step 2 above will be excuted and returns to normal TV picture.
NO STATION
PLEASE CONNECT ANTENNA PLUG!
Figure B.
PLEASE SELECT AND PRESS ENTER BUTTON
TEMPORAL CANCEL PERMANENT CANCEL
:
SELECT
ENTER
:
ENTER
SELECTING INPUT SOURCE
Select mode "TV", "AV1", "AV2", "HDMI" or "PC" by pressing INPUT button on Remote Control or on Side Controls, you can also press
POINT ▲▼ buttons to select different mode. To enter the selected mode, press ENTER button or POINT ◄► buttons.
REMOTE CONTROL
Note:
SIDE CONTROL
INPUT
1. TV
2. AV1
3. AV2
4. HDMI
5. PC
User can directly displayed
selected input source by
pressing NUMERIC buttons
(1-5) on Remote Control.
INPUT
button
INFO
button
1~5
: SELECT
: EXIT
INPUT
button
BACK
NUMERIC
buttons
CHANNEL RECALL
Press CHANNEL RECALL button to switch between the previous channel and the current channel.
For example, now you are watching channel "4", but you watched channel "2" previously. If you
press CHANNEL RECALL button, channel "2" will appear immediately.
CHANNEL
UP/DOWN
(▲▼) buttons
CHANNEL SELECTION
There are 256 channels can be selected on the LCD TV.
CHANNEL
RECALL
button
DIRECT SELECTION
For direct access to programmes using the (0-9) numeric buttons.
1) For selection of channel position 0 - 9. Example: For channel position 8, press “8” button.
DIGIT
button
2) For selection of channel position 10 - 99. Example:
For channel position 25, press the DIGIT button to display "- -", then press “2” and “5” buttons.
3) For selection of channel position 100 - 199. Example:
For channel position 125, press the DIGIT button twice to display "1 - -", then press “2” and “5” buttons.
4) For selection of channel position 200 - 255. Example:
For channel position 225, press the DIGIT button three times to display "2 - -", then press “2” and “5”
buttons.
CHANNEL UP/ DOWN
Press CHANNEL UP/DOWN (▲▼) buttons on Side Control or on Remote Control to select programs.
●
●
Press CHANNEL UP (▲) button to select next channel.
Press CHANNEL DOWN (▼) button to select previous channel.
Note:
CHANNEL RECALL and CHANNEL SELECTION function only use in TV mode.
9
BASIC OPERATION
INFO
Press INFO button on Remote Control to display the status of LCD TV. Press again to remove the display.
Channel
11
Colour System
Sound System
STEREO/MONO
AUTO
B/G
MONO
VOLUME CONTROL
To adjust the volume value desired by pressing VOLUME(+/-) buttons on Remote Control or on Side
Control. The volume dialogue box will appear on the screen for a short while. VOLUME(+) button
to increase volume, and VOLUME(-) button to decrease volume.
REMOTE CONTROL
MUTE
SOUND button
VA·B button
Should you wish to mute the sound, press MUTE button. To switch the sound back on, press
MUTE button again or press VOLUME(+/-) buttons on Side Control or on Remote Control.
PICTURE button
SPORTS button
STEREO/MONO
Press the VA·B button on Remote Control to show the information display. And then press VA·B
button to select the following audio signals: "STEREO", "MONO", "NICAM", "A", and "B".
SOUND MODE
Select sound level by pressing SOUND button on Remote Control.
STANDARD: Normal sound state preset on LCD TV.
NEWS: Select this mode for talk programs.
VOLUME(+/-)
buttons
MUSIC: Select this mode for music programs.
PERSONAL: Select this mode for user to call out the preset sound adjustment in SOUND
menu.
MUTE button
PICTURE MODE
Select image level by pressing PICTURE button on Remote Control.
STANDARD: Natural and splendid picture level preset on this LCD TV.
VIVID: Present colourful and lively picture level.
SOFT: Inhibit strong contrast and color, it is beneficial for eye protection.
PERSONAL: User presets picture adjustment in PICTURE MODE.
DYNAMIC: Bright and dynamic picture. It is suitable for nice playback, such as DVD program.
Note:
Select ECO in SETUP menu. Then press ◄► buttons to select "ON". While in ECO status, press PICTURE button to choose any of options
of "ECO LOW/STANDARD", "ECO LOW/VIVID", "ECO LOW/SOFT", "ECO LOW/PERSONAL" and "ECO HIGH/DYNAMIC", or "ECO HIGH/
STANDARD", "ECO HIGH/VIVID", "ECO HIGH/SOFT", "ECO HIGH/PERSONAL" and "ECO HIGH/DYNAMIC".
SPORTS MODE
Just by pressing the button, sports mode optimizes picture and sound settings suitable for each sports program.
ƒ OFF: Normal setting.
ƒ Football: Use to watch football program, golf program or etc.
ƒ Winter Sport: Suitable setting for skiing program or etc.
ƒ Marine Sport: Suitable setting for swimming, diving program or etc.
ƒ Indoor Sport: Suitable setting for basketball, badminton program or etc.
Note:
Press SOUND button in SPORTS mode, only current SPORTS mode is displayed.
OFF TIMER
To set OFF TIMER by pressing TIMER button on Remote
REMOTE CONTROL
Control. The timer dialogue box will appear on the screen for a short while.
To select "OFF", "30 MIN", "60 MIN", "90 MIN" or "120 MIN" with TIMER buttons.
WIDE button
TIMER button
WIDE
Select screen size among "FULL", "ZOOM", "ZOOM[CAPTION-IN]", and "NORMAL" by pressing WIDE button
on Remote Control.
*
*
*
This function doesn't work in TV/ AV/ DVD/ HDMI/ PC modes when no signal is input.
Only "FULL" mode can be selected when the input mode is "HDMI" or "DVD" and the input signal is 1080i, 720p or 1080p.
"FULL" and "NORMAL" can be selected in PC mode.
FULL: Provides image to fit width of screen by expanding image width uniformly. This function can be used
for enjoying a squeezed video signal with wide video aspect ratio of 16 : 9 screen. When your video equipment
(such as DVD) has 16 : 9 output mode, select 16 : 9 and select "Full" to provide better quality.
ZOOM: Provides image to fit screen size (16 : 9 aspect ratio) by expanding image width and height uniformly.
This function can be used for enjoying a letter box mode picture (4 : 3 aspect picture with black bar on top and
bottom edges) with wide video aspect of 16 : 9 screen.
10
MENU OPERATION
ZOOM[CAPTION-In]: Provides the image that is expanded as "ZOOM" mode and moved up to show more
image to include captions. This function can be used for enjoying a letter box picture with captions.
NORMAL: Provides real 4 : 3 image on 16 : 9 screen.
CHANNEL
Press MENU button and the main menu will appear. Whenever MAIN MENU is accessed initially,
CHANNEL will be the default selection.
CHANNEL MENU
1
Press POINT ▲▼ buttons or ENTER button to enter into CHANNEL menu.
2
Press POINT ▲▼ buttons to select the item desired.
CHANNEL
3
AUTO SEARCH
Press POINT ◄► buttons to adjust the item.
SEMI-AUTO SEARCH
MANUAL SEARCH
COLOUR SYSTEM
4
■
■
Press BACK button to return to the previous menu.
Press MENU button or wait for 5~60 seconds to exit menu operation.
AUTO
SOUND SYSTEM
SKIP
B/G
OFF
CHANNEL SWAP
Note:
● "CHANNEL" menu doesn't work in HDMI mode and PC mode.
●
●
In AV mode, only "COLOUR SYSTEM" in "CHANNEL" menu can be selected.
The settings for "SOUND SYSTEM", "COLOUR SYSTEM" or "SKIP" are automatically memorized in
the programme position.
:
:
:
:
SELECT
BACK
EXIT
ADJUST
AUTO SEARCH
AUTO SEARCH MENU
All receivable channels are automatically tuned in and memorized in consecutive programme
position.
● The Automatic Tuning operation can be cancelled at any time by pressing BACK button or
MENU button.
AUTO SEARCHING, PLEASE WAIT…
55.25
MHZ
CH
2
: EXIT
: BACK
● After all receivable channels have been found and stored, the TV set will automatically return
to programme position “1”.
Note:
POINT ◄► buttons or ENTER button: Start or Restart AUTO SEARCH.
SEMI-AUTO SEARCH
Use to preset a receivable channel in any desired programme position, e.g. the position with
the same number as the channel.
SEMI-AUTO SEARCH MENU
Select channel “15”.
SEMI-AUTO SEARCHING
1
2
CHANNEL
SEARCH
15
Enter into CHANNEL menu, press POINT ▲▼ buttons to select "SEMI-AUTO SEARCH".
Press POINT ◄► buttons to enter into the SEMI-AUTO SEARCH menu.
55.25 MHZ
BACK
:
:
:
SELECT
ADJUST
Press POINT ▲▼ buttons to select "SEARCH". Press POINT ◄► buttons to start the
channel searching.
3
Press POINT ► button and the tuning will go to the higher frequencies. Press POINT ◄
button and the tuning will go to the lower frequencies. Use POINT ◄ button or POINT
4
► button to search for required TV station. Once a station is located, searching will
automatically stop. Continue till desired channel is located.
SEMI-AUTO SEARCH COMPLETED
CHANNEL
SEARCH
15
■
■
Press BACK button to return to the previous menu.
Press MENU button to exit menu operation.
55.25 MHZ
BACK
:
:
:
SELECT
ADJUST
MANUAL SEARCH
Manual search a channel if it cannot be automatically tuned, such
as when the signal is poor.
MANUAL SEARCH MENU
Select channel “15”.
1
MANUAL SEARCH
Enter into CHANNEL menu, press POINT ▲▼ buttons to select "MANUAL SEARCH".
Press POINT ◄► buttons to enter into the MANUAL SEARCH menu.
2
CHANNEL
SEARCH
15
55.25 MHZ
Press POINT ▲▼ buttons to select "SEARCH". Press POINT ◄► buttons to start the
channel searching.
3
:
:
:
SELECT
:
BACK
ADJUST ENTER STORE
Press and hold POINT ◄ or POINT ► button to search for required TV station. Press
ENTER button to save desirable station.
4
■
■
Press BACK button to return to the previous menu.
Press MENU button to exit menu operation.
MANUAL SEARCH
CHANNEL
15
SEARCH
55.25 MHZ
:
:
:
SELECT
:
BACK
ADJUST ENTER STORE
11
MENU OPERATION
COLOUR SYSTEM
The setting for colour system is only active in TV or AV mode. Usually, the colour system is set to
the position of "AUTO". In case of abnormal colour, repeatedly press POINT ◄► buttons to select
"AUTO", "PAL", "SECAM", "NTSC" or "NTSC4.43" until the best colour effect is reached.
CHANNEL
SOUND SYSTEM
AUTO SEARCH
The setting for sound system is only active in TV mode. Usually, the sound system is set to the
position of "B/G". In case of abnormal sound, repeatedly press POINT ◄► buttons to select "D/K",
"I", "M" or "B/G" until the best sound effect is reached.
SEMI-AUTO SEARCH
MANUAL SEARCH
COLOUR SYSTEM
AUTO
SOUND SYSTEM
SKIP
B/G
OFF
SKIP
CHANNEL SWAP
This feature is used to remove unwanted channels from the channel scanning memory.
You can skip the unused or undesired channels when you are
selecting a channel using CHANNEL UP/DOWN (▲▼) buttons.
This function is only active in TV mode.
:
:
:
:
EXIT
SELECT
BACK
ADJUST
CHANNEL SWAP
To swap the channels between two stored programme positions.
Press MENU button to display the main menu.
1
Enter into "CHANNEL" menu, press POINT ▲▼ buttons to select CHANNEL SWAP.
2
CHANNEL
CHANNEL SWAP
Press POINT ◄► buttons or ENTER button to enter into the CHANNEL SWAP menu. Press
3
CURRENT CHANNEL
TARGET CHANNEL
SWAPPING
12
16
POINT ▲▼ buttons to select the CURRENT CHANNEL or TARGET CHANNEL, then press
POINT ◄► buttons to select the swap channel. And then press POINT ▲▼ buttons to select
SWAPPING item, then press POINT ◄► buttons or ENTER button to select "OK".
■
■
Press BACK button to return to the previous menu.
Press MENU button or wait for 5~60 seconds to exit menu operation.
Note:
:
:
:
:
EXIT
SELECT
BACK
ADJUST
When enter into CHANNEL SWAP menu again, TARGET CHANNEL will be turn to 0.
PICTURE
Press MENU button and the main menu will appear. Press POINT ◄► buttons to select
"PICTURE", and will display PICTURE menu.
1
Press POINT ▲▼ buttons or ENTER button to enter into PICTURE menu.
CHANNEL
CHANNEL SWAP
2
Press POINT ▲▼ buttons to select the item desired.
CURRENT CHANNEL
12
3
TARGET CHANNEL
SWAPPING
16
Press POINT ◄► buttons to adjust the item.
OK
4
■
■
Press BACK button to return to the previous menu.
Press MENU button or wait for 5~60 seconds to exit menu operation.
PICTURE MODE: Used for selecting "STANDARD", "VIVID", "SOFT", "PERSONAL" or "DYNAMIC"
.
CONTRAST: Used to decrease and increase contrast.
:
:
:
:
SELECT
BACK
EXIT
ADJUST
BRIGHTNESS: Used to adjust darken and brighten image.
PICTURE MENU (TV/AV/HDMI MODE)
COLOUR: Used for lighten and darken colour. (Only in TV/AV/HDMI mode).
TINT: Used to obtain proper colour.
SHARPNESS: Used for soften and sharpen the image. (Only in TV/AV/HDMI mode).
COLOUR TONE: Used for selecting colour temperature. Select "NORMAL", "WARM" or "COOL".
PICTURE
GAMMA: This function is used for adjusting the gamma value to obtain a better balance of
contrast. Select "LOW", "MIDDLE", or "HIGH".(Only in TV/AV/HDMI mode).
PICTURE MODE
STANDARD
CONTRAST
BRIGHTNESS
COLOUR
COLOUR-R: Used to lighten and deepen red tone. (Only in PC mode).
COLOUR-G: Used to lighten and deepen green tone. (Only in PC mode).
COLOUR-B: Used to lighten and deepen blue tone. (Only in PC mode).
TINT
SHARPNESS
COLOUR TONE
GAMMA
NORMAL
LOW
Note:
●
"TINT" cannot be selected except for NTSC/ NTSC4.43 system.
●
Only COLOUR TONE and GAMMA are available when SPORTS mode is ON.
:
:
:
:
SELECT
BACK
EXIT
ADJUST
PICTURE MENU (PC MODE)
PICTURE
PICTURE MODE
STANDARD
NORMAL
CONTRAST
BRIGHTNESS
COLOUR TONE
COLOUR - R
COLOUR - G
COLOUR - B
:
:
:
:
SELECT
BACK
EXIT
ADJUST
12
MENU OPERATION
SOUND
SOUND
SOUND
SOUND
SOUND MODE
STANDARD
EQUALIZER
SOUND MODE
EQUALIZER
BALANCE
STANDARD
EQUALIZER
BALANCE
500 Hz
1.5K Hz
5K Hz
BASS EXPANDER
AUTO VOLUME
BASS EXPANDER
AUTO VOLUME
OFF
OFF
OFF
OFF
10K Hz
:
:
:
:
:
:
:
:
SELECT
BACK
EXIT
SELECT
BACK
EXIT
ADJUST
ADJUST
:
:
:
:
SELECT
BACK
EXIT
ADJUST
SOUND MODE: Press POINT ◄► buttons to select
"STANDARD", "NEWS", "MUSIC" or "PERSONAL".
Press MENU button and the main menu will appear. Press POINT
◄► buttons to select "SOUND", and will display SOUND menu.
1
2
EQUALIZER: Select different frequency ranges of sound
separately by pressing POINT ◄► buttons or ENTER button.
Adjust values of "500 Hz", "1.5 K Hz", "5K Hz", "10K Hz" by pressing
POINT ◄► buttons.
Press POINT ▲▼ buttons or ENTER button to enter into SOUND
menu.
Press POINT ▲▼ buttons to select the item desired.
3
4
BALANCE: Adjust the balance of the left and right channels.
(-15~15).
Press POINT ◄► buttons to enter the item selected.
■
■
Press BACK button to return to the previous menu.
Press MENU button or wait for 5~60 seconds to exit menu operation.
BASS EXPANDER: Switch Bass Expander ON or OFF.
AUTO VOLUME: Switch Auto Volume ON or OFF.
Note:
SOUND MODE, EQUALIZER and BASS EXPANDER is disabled when SPORTS mode is ON.
TIMER
Press MENU button and the main menu will appear. Press POINT ◄► buttons to
select "TIMER", and will display TIMER menu.
TIMER MENU
1
Press POINT ▲▼ buttons or ENTER button to enter into TIMER menu.
2
TIMER
Press POINT ▲▼ buttons to select the item desired.
3
OFF TIMER
ON TIMER
OFF
12 : 30
01
Press POINT ◄► buttons to enter the item selected.
4
ON TIMER CH
■
■
Press BACK button to return to the previous menu.
Press MENU button or wait for 5~60 seconds to exit menu operation.
OFF TIMER: Once OFF TIMER has been set, when the set time is reached, the TV will
shift to stand-by status. To select "OFF", "30 MIN", "60 MIN", "90 MIN" or "120 MIN"
with POINT ◄► buttons or TIMER button. To cancel "OFF TIMER ", you can choose
any option by the following ways.
:
:
:
:
SELECT
BACK
EXIT
ADJUST
- Setting "OFF" in OFF TIMER menu.
- Pressing POWER ON/OFF button on Side Control.
- Pressing POWER ON/OFF button on Remote Control.
ON TIMER: Once ON TIMER has been set, you won't miss any opportunity to watch the program you like. To set channel position, you can
use NUMERIC buttons or DIGIT button. After ON TIMER has been set, ON TIMER INDICATOR will be light. To cancel "ON TIMER MODE", you
can choose any option by the following ways.
- Setting "- - : - -" in ON TIMER.
- Disconnecting the AC power cord.
ON TIMER CH: This function is only active that ON TIMER has been set. When the set time in ON TIMER is reach, the TV will turn on and
enter the channel position you set directly. To set channel position, you can use NUMERIC buttons or DIGIT button.
●
●
●
●
●
●
When OFF TIMER countdown time reach 1 minute, OFF TIMER OSD always showed for user information about power off time remain.
OFF TIMER will be cancel when press any button during the countdown time dsplay.
If ON TIMER didn't set, ON TIMER CH function will not actived.
OFF TIMER and ON TIMER will be automatically cancelled during searching channels.
The settings for OFF TIMER and ON TIMER will be automatically cancelled after the settings has been operated for one time.
In case you left TV without any operation for 2 hours after power on by ON timer, TV will automatically power off itself.
OSD
Press MENU button and the main menu will appear. Press POINT ◄► buttons to select "OSD"
and will display OSD menu.
,
1
OSD
ENGLISH
5 SEC
LANGUAGE
H - POSITION
V - POSITION
DURATION
Press POINT ▲▼ buttons or ENTER button to enter into OSD menu.
2
3
4
Press POINT ▲▼ buttons to select the item desired.
INPUT LABEL
Press POINT ◄► buttons to enter the item selected.
■
■
Press BACK button to return to the previous menu.
Press MENU button or wait for 5~60 seconds to exit menu operation.
:
:
:
:
SELECT
BACK
EXIT
ADJUST
13
MENU OPERATION
LANGUAGE: Press POINT ◄► buttons to choose ENGLISH, THAILAND, VIETNAM, or INDONESIA. For
Middle East destination, it will be displayed: ENGLISH, ARABIC or PERSIAN.
H-POSITION: OSD moves to the left side when POINT ◄ button is pressed. OSD moves to the right side
OSD
INPUT LABEL
when POINT ► button is pressed. (0~100).
OFF
OFF
OFF
AV1
V-POSITION: OSD moves up when POINT ◄ button is pressed. OSD moves down when POINT ► button
is pressed. (0~100).
AV2
HDMI
DURATION: Use this function to set the display time of the MENU when there is no operation on the TV.
Press POINT ◄ button to decrease time, press POINT► button to increase time. (5~60 seconds).
INPUT LABEL: Use this function to give input source tag name follows input source device (ex: DVD player,
Blu-Ray player, etc). Press POINT ◄► buttons or ENTER button to enter into INPUT LABEL menu. Press
POINT ▲▼ buttons to select INPUT source, press POINT ◄► buttons to select "OFF"(blank), VCR, DVD,
AUX, STB or GAME.
:
:
:
:
SELECT
BACK
EXIT
ADJUST
Note:
User can switch off or fill INPUT LABEL names with blank, by choosing "OFF" at INPUT LABEL menu option.
SETUP
INPUT MENU
Press MENU button and the main menu will appear.
Press POINT ◄► buttons to select "SETUP", and will display SETUP menu.
1
INPUT
Press POINT ▲▼ buttons or ENTER button to enter into SETUP menu.
2
1. TV
- VCR
- GAME
- DVD
2. AV1
3. AV2
4. HDMI
5. PC
Press POINT ▲▼ buttons to select the item desired.
3
4
■
■
Press POINT ◄► buttons to enter the item selected.
Press BACK button to return to the previous menu.
Press MENU button or wait for 5~60 seconds to exit menu operation.
1~5
: SELECT
Note:
BACK
: EXIT
"PC ADJUST" can not be selected except for PC mode.
SETUP MENU
CHILD LOCK: When CHILD LOCK is set "ON", the Side Control buttons will be locked except for
POWER ON/OFF button. When Press the Side Control buttons, TV will display "LOCKED".
ECO: This mode adjust panel backlight that can reduce the power consumption. Set it ECO "OFF",
"LOW", or "HIGH".
SETUP
CHILD LOCK
ECO
ON
OFF
DYNAMIC AI: Automatically adjust video quality by video scene. Used to adjust contrast and color
parameters until the display looks good. Set it ON or OFF.
DYNAMIC AI
ACTIVE CONTRAST
PC ADJUST
ON
OFF
ACTIVE CONTRAST: Used to improve poor contrast level quality from source signal in certain
condition. Set it "OFF", "LOW, or "HIGH".
SHOP MODE
SHOP MODE: Press POINT ◄► buttons to choose HOME MODE or SHOP MODE. Press ENTER
button to enter into HOME MODE or SHOP MODE.
:
:
:
:
SELECT
BACK
EXIT
ADJUST
HOME MODE: In this mode, the adjustments you have set of "Picture mode" and "ECO" will be
stored as the last memory automatically. The initial settings are "DYNAMIC" and "OFF".
SHOP MODE: In this mode, 30 minutes later after you made some adjustments of "Picture mode" and "ECO" and no other operation on
the LCD TV, the initial setting will be recalled. (The initial settings are "DYNAMIC" and "OFF".) The message of "INITIAL SETTING
RECALLED FOR DEMO" will appear on the screen for 3 seconds.
PLEASE SELECT AND PRESS ENTER BUTTON
HOME MODE
SHOP MODE
INITIAL SETTING RECALLED FOR DEMO
:
SELECT
:
ENTER
ENTER
Note:
● When Active Contrast is select "HIGH" mode, the picture may be too darkness. In this case, select "OFF" or "LOW" mode.
● When in PC mode, "ACTIVE CONTRAST" can not be adjusted in the "SETUP" menu.
●
●
Shop mode setting will be continued even after power off /on by Remote control, LCD TV or AC power plug.
At the first power on and just after plug and play channel set-up, SHOP MODE menu will appear. Press POINT ◄► buttons to select and press
ENTER button for SHOP MODE or HOME MODE. Then the pop up menu disappears.
SETUP (PC MODE)
Press MENU button and the main menu will appear. Press POINT ◄► buttons to select "SETUP", and
will display SETUP menu.
SETUP MENU
1
Press POINT ▲▼ buttons or ENTER button to enter into SETUP menu.
2
3
Press POINT ▲▼ buttons to select the item desired.
SETUP
CHILD LOCK
ECO
ON
OFF
Press POINT ◄► buttons to enter the item selected.
4
DYNAMIC AI
ON
ACTIVE CONTRAST
PC ADJUST
OFF
■
■
Press BACK button to return to the previous menu.
Press MENU button or wait for 5~60 seconds to exit menu operation.
SHOP MODE
Note:
● "PC ADJUST" is only active in PC mode.
:
:
:
:
SELECT
BACK
EXIT
ADJUST
PC ADJUST
This function is used to adjust the position of image displayed on screen. It can be selected when the LCD TV could be received PC signal and in PC
mode. Press POINT ◄► buttons or ENTER button to enter PC ADJUST menu. It can be select "AUTO ADJUST", "H-POSITION", "V-POSITION",
"PHASE", "CLOCK" or "AUTO SHUT DOWN" to adjust.
14
DEALER MODE
AUTO ADJUST: Press POINT ◄► buttons, and the TV automatically detects incoming signal, and
adjust itself to optimize its performance. If the image is not displayed properly, a manual adjustment
is required (Refer to following adjustments).
SETUP
CHILD LOCK
ECO
ON
H-POSITION: The horizontal picture position will be moved to the left side by pressing POINT ◄
OFF
button. And it will be moved to the right side by pressing POINT ► button. (0~100).
DYNAMIC AI
ON
ACTIVE CONTRAST
PC ADJUST
OFF
V-POSITION: The vertical picture position will be moved down side by pressing POINT ◄ button.
And it will be moved up side by pressing POINT ► button. (0~100).
SHOP MODE
PHASE: Eliminate disorder from the image. Press POINT ◄► buttons to adjust PHASE. (0~100).
CLOCK: Eliminate flicker from the image. Press POINT ◄► buttons to adjust CLOCK. (0~100).
:
:
:
:
SELECT
BACK
EXIT
ADJUST
AUTO SHUT DOWN: Press POINT ◄► buttons to set AUTO SHUT DOWN ON or OFF. When
PC is switched Off, ''NO SIGNAL'' appears for 30 seconds, TV will be automatically switched to
Backlight off mode. During Backlight Off Mode within 10 minutes, TV will be switched to On Mode
if PC is switched On. After Backlight Mode continues for 10 minutes, it will be switched to Standby
Mode. During Standby mode, TV will not be switched to On mode even if PC is switched On. During
Backlight Off mode, POWER indicator will become green.POWER ON/OFF button, NUMERIC (0-9)
buttons and CHANNEL up/down buttons are enabled to switch On TV.
SETUP
PC ADJUST
AUTO ADJUST
H
V
-
-
POSITION
POSITION
DEALER MODE
TO DISPLAY DEALER MODE:
PHASE
CLOCK
Press INFO button on remote control while holding MENU button on Side control to display Dealer
AUTO SHUT DOWN
ON
mode menu.
The Dealer Mode has 9 different modes: VOLUME LOCK, TUNING LOCK, START MODE, OSD,
RC, AC POWER MODE, START VOLUME LEVEL, MUSIC MODE SETUP and RESET.
Take the way of setting VOLUME LOCK for example:
:
:
:
:
SELECT
BACK
EXIT
ADJUST
Press POINT ◄► buttons to select a maximal volume.
1
AUTO ADJUST
Press INFO button on remote control while holding MENU button on Side control to display
2
Dealer mode menu.
VOLUME LOCK will be the default selection. (When you adjust others, press POINT ▲▼
buttons to select the item desired.)
REMOTE CONTROL
3
Press POINT ◄► buttons to select "ON". (The maximal volume is the set value by step 1.)
4
Press menu button to exit menu operation.
5
INFO button
VOLUME LOCK
This function is used to limit the maximal volume.
TUNING LOCK
The way to prevent user from executing the Tuning function.
POINT
▲/▼/◄/►
buttons
START MODE
The LCD TV will automatically enter to the setting mode while being turned on. You can select
OFF, TV(0-10), AV1, AV2(DVD), HDMI or PC in START MODE. When it is set "OFF", it will
keep the mode before being turning off.
OSD
When it is set "OFF", Corresponding OSD cannot display on the screen while operating.
SIDE CONTROL
RC
You can set "ON" or "OFF" in RC MODE. Use this feature to set Remote Control Function
including Power ON/OFF function.
● ON
- Set Remote Control to normal function.
● OFF
MENU button
-
Set buttons on the Remote Control to prohibit to use include Power button.
AC POWER MODE
You can set "STAND", "LAST" or "ON" in AC POWER MODE.Use this feature to set TV
condition when AC cord plug-in.
● STAND
- When AC cord plug-in, LCD TV always STAND-BY.
● LAST
DEALER MODE MENU
- When AC cord plug-in, the LCD TV will depend on last TV condition. (ON or Stand-by)
● ON
DEALER MODE
- When AC cord plug-in, LCD TV always ON.
VOLUME LOCK
TUNING LOCK
START MODE
OFF
OFF
OFF
ON
START VOLUME LEVEL
You can select "OFF" or "1-100" in START VOLUME LEVEL.
Use this feature to set volume bar level position every time TV turned on.
OSD
ON
STAND
OFF
RC
Note:
AC POWER MODE
START VOLUME LEVEL
MUSIC MODE SETUP
RESET
Even Start Volume Level set to higher value then Volume Lock, the Start
Volume Level value automatically set to Volume Lock value.
:
SELECT
:
ADJUST
:
EXIT
15
DEALER MODE
MUSIC MODE SETUP
DEALER MODE
MUSIC mode is used to block picture on channel program.Use this feature to set Music
Mode condition in set 5 Position Channel.
VOLUME LOCK
TUNING LOCK
START MODE
OFF
OFF
OFF
ON
Press and hold Menu button on Side Controls, and press INFO button on remote control to
display Dealer mode menu. Press POINT ▲▼ buttons to select MUSIC MODE SETUP.
1
OSD
ON
STAND
OFF
RC
Press POINT ◄► buttons or ENTER button to enter into MUSIC MODE SETUP menu.
2
3
AC POWER MODE
START VOLUME LEVEL
MUSIC MODE SETUP
RESET
Press POINT ▲▼ buttons to select the item desired.
Press POINT ◄► buttons to enter the item selected.
4
:
SELECT
:
ADJUST
:
EXIT
■
■
Press BACK button to return to the previous menu.
Press MENU button or wait to exit menu operation.
Note:
MUSIC MODE SETUP
When the channel set with Music mode is selected, Eco mode is ON.
MUSIC MODE POS1
MUSIC MODE POS2
MUSIC MODE POS3
1
255
255
255
RESET
This function returns all setting values to the factory default settings.
MUSIC MODE POS4
MUSIC MODE POS5
255
:
SELECT
:
ADJUST
BACK
:
BACK
: EXIT
APPENDIX
CLEANING LCD TV
Be sure to disconnect the AC Power cord from AC outlet before cleaning the LCD TV.
Clean your LCD TV as follows:
● Gently wipe the screen and cabinet with dry soft cloth.
● The screen is likely to be damaged if it is not maintained properly. Do not use hard objects
like a hard cloth or paper. Do not use solvents or abrasions.
CAUTION :
Do not use benzene, thinner, or any volatile substances to clean the LCD TV. These
chemicals may damage the cabinet finish.
FUNCTION OF PRODUCT SAFETY FEATURE
For protecting product safety, protection feature provided inside LCD TV. Refer to the
following please.
AUTO POWER OFF
When a trouble is detected in the LCD TV, the protection function works and turn the LCD TV
OFF automatically. When the LCD TV is turned OFF with this function, the POWER indicator
becomes red and LCD TV's power cannot be turned ON.
Disconnect Power cord and contact sales dealer where you purchased the LCD TV or the
service center.
To turn on LCD TV again for checking:
1) Disconnect Power cord from AC outlet and plug it on again.
2) Refer to "TURNING ON/OFF LCD TV" to attempt to turn on LCD TV.
If LCD TV is not turned on, disconnect Power cord and contact to service center.
16
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check the matters below once again.
1. Make sure you have connected LCD TV to your equipment as described in the section "CONNECTING LCD TV".
2. Check cable connection. Verify that all external equipment and power cords are properly connected.
3. Verify that all power is switched on.
4. If LCD TV still does not produce an image, re-start the external equipment.
5. If the image still does not appear, unplug LCD TV from the external equipment and check the external
equipment. The problem may be with your graphics controller rather than with LCD TV. (When you reconnect
LCD TV, remember to turn the external equipment and TV off before you power up LCD TV. Power
the equipment back on in order of : LCD TV and external equipment.)
6. If the problem still exists, check the following chart.
Problem:
Try these Solutions
● Plug this LCD TV into the AC outlet.
NO
● Press ON/STAND-BY button on SIDE Control or on Remote Control to open this LCD TV.
● Check POWER Indicator. If this indicator flashes, LCD TV has any trouble.
POWER
● Check the batteries.
Remote
Control
does not
work
● Make sure nothing is between the Remote Receiver and the Remote Control.
● Make sure you are not too far from LCD TV when using Remote Control.
Maximum operating range is 16.4' (5m).
● Is direct sunlight or strong artificial light shining on LCD TV's Infrared Remote
Receiver? Eliminate the light by closing curtains, pointing the light in a different
direction, etc.
● Check the connection between the external equipment and LCD TV.
● When turning LCD TV on, it takes a few seconds to display the image.
● Check the system that you select is corresponding with the external equipment or the video
equipment.
No image
● Make sure the temperature is not out of the Operating Temperature (0°C ~ 40°C).
● Turn off power, then turn on again, re-start LCD TV.
● Check Audio cable connection from Audio input source.
● Adjust the Audio source.
No sound
● Press VOLUME (+) button.
● Press MUTE button.
There are
tiny black
points
and/or
bright
● Dark or bright points of light (red, green, or blue) may appear on the screen. This is a
characteristic of the LCD panels, not a malfunction of the LCD TV.
point on
the TV
Abnormal
colour of
image
● Adjust the value of colour.
● Select different colour system.
WARNING :
High voltages are used to operate this LCD TV. Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions, contact the sales dealer where you
purchased LCD TV or the service center. Give the model number and explain the difficulty. We will advise you
how to obtain service.
17
APPENDIX
TECHNICAL SPECIFICATIONS
Model
LCE-24C100F(K)/(N)/(R)/(S)
Maximum Visible Range
Picture Resolution
Voltage
61cm (Screen Diagonal Size)
1920(H) x 1080(V)
AC110-240V 50/60Hz
Power Consumption
Power Management
Colour System
Sound System
Channel Coverage
LCE-24C100F(K)/(N)/(R)/(S): 44W
VESA DPMS
PAL/SECAM/NTSC/NTSC4.43
D/K, I, M, B/G
- VHF: E2-E12, R1-R12, K1-K9, J1-J12, A2-A13
- UHF: 21-69, A14-A69, J13-J62
- CATV: S1-S41, X, Y, Z, Z+1, Z+2
75Ω
Mains: 80mm x 20mm x 2pcs
Maximum Output Power is 3W+3W
Total Harmonic Distortion(THD)≤10%
Aerial input impedance
Speaker Size
Sound speciality
Input and Output terminals
AV1 Input
Video Input: Composite video Input (RCA Jack) x1
Audio Input: L/R Stereo Input (RCA Jack) x 1 set
Video Input: Component Y (combined with composite video input),
CB, CR Input (RCA Jack) x1 set
AV2 Input
Audio: L/R Stereo Input (RCA Jack) x 1 set
HDMI Terminal 19 pin x1
Video Input: D-SUB 15 pin x1
HDMI Input
PC Input
Audio Input: Mini stereo jack x 1
Output Terminals
Video Monitor Output: RCA jack x 1
Audio Monitor Output: L/R Stereo Output (RCA jack) x 1 set
Dimensions
(Width x Height x Depth)
LCE-24C100F(K)/(N)/(R)/(S): 580 x 396 x 156 mm (Including Stand)
Net Weight
g
(Including Stand )
LCE-24C100F(K)/(N)/(R)/(S): 4.25 k
Wall Mounting
VESA Standard (200 x 200) wall hanging bracket.
Operating Environment
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
0ºC~40ºC 32ºF~104ºF
20~80%
（
）
-10ºC~50ºC 14ºF~122ºF
（
）
20~80%
18
APPENDIX
SIGNAL MODE COLUMN (Recommended)
This LCD TV can correspond to the signals below. After connecting with the computer, LCD TV can automatically
recognize the signal from the connected PC( computer)/ HDMI.
PC SIGNAL MODE COLUMN (recommended)
Note:
● In case LCD TV can not display properly due to the connecting cable or the graphic hardware, please make
adjustments about phase, clock and so on.
● In principle, LCD TV can not display the signal mode which not described in the above column. But sometimes
it can display a signal very similar with one of the signal described.
● If you want to change the definition and colour of PC, please select one from the column.
●
●
It is not the trouble of LCD TV if interference appears on the picture while switching the signal mode.
It is different from CRT Monitor that it is no blink of the picture when the V-Freq. of the signal s 60Hz. It is
recommended to select 60Hz V-Freq. of your computer to display better pictures.
● The Dot Clock of the computer's signal must be less than 100 MHz.
● Specifications are subject to change without notice.
In case of the following things, some messages will display on the screen.
● When the input signal from PC is out of the display range, "OUT OF RANGE" will display.
When input signal is digital from DVD terminal, refer to the chart below.
When input signal is digital from HDMI terminal, refer to the chart below.
Frame
NO.
Resolution
Frequency
60.00HZ
EIA1920×1080i@60
EIA1920×1080p@60
EIA1920×1080i@50
EIA1920×1080p@50
33.750
67.500
28.125
60.00HZ
50.00HZ
56.250
45.000
37.500
31.500
31.250
50.00HZ
60.00HZ
50.00HZ
60.00HZ
50.00HZ
EIA1280×720p@60
EIA1280×720p@50
EIA720x480p(w)@60
EIA720x576p(w)@50
Audio Freq. Format :
HDMITM(V.1.3 with Deep Color）
19
SANYO Electric Co., Ltd.
Printed in Indonesia
(
)
Part No: 1AA6P1P5969-- Z5YJ UE7-D
|