Sanyo Camcorder VCB 3384 User Guide

INFORMATION TO USER  
PRECAUTIONS  
I In case of problem  
I Protect from high temperatures  
Safety Guard  
Do not use the camera if smoke or a strange odor comes from the  
unit, or if it seems not to function correctly. Disconnect the power  
cord immediately, and consult your dealer or a Sanyo Authorized  
Service Center.  
Do not install close to stoves, or other heat generating devices, such  
as spotlights, etc., or where it could be subject to direct sunlight, as  
that could cause deformation, discoloration or other damages.  
Be careful when installing close to the ceiling, in a kitchen or boiler  
room, as the temperature may raise to high levels. Install where the  
temperature range will stay between –10°C (14°F) and 50°C  
(122°F). (no condensation)  
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT  
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE  
LITERATURE ACCOMPANYING THIS UNIT.  
INSTRUCTION MANUAL  
(Warranty attached)  
VCB-3384  
WARNING:  
B/W CCD camera  
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE  
THIS APPLIANCE TO RAIN OR MOISTURE.  
I Do not open or modify  
Do not open the cabinet, as it may be dangerous and cause damage  
to the unit. For internal settings and repairs, consult your dealer or a  
Sanyo Authorized Service Center.  
About this manual  
For the customers in Canada  
This Class B digital apparatus complies with Canadian ICES-003.  
I Cleaning  
Before installing and using the camera, please read this manual  
carefully. Be sure to keep it handy for later reference.  
Dirt can be removed from the cabinet by wiping it with a soft cloth.  
To remove stains, wipe with a soft cloth moistened with a soft  
detergent solution and wrung dry, then wipe dry with dry soft cloth.  
Do not use benzine, thinner or other chemical product on the  
cabinet, as that may cause deformation and paint peeling. Before  
using a chemical cloth, make sure to read all accompanying  
instructions. Make sure that no plastic or rubber material comes  
in contact with the cabinet for a long period of time, as that may  
cause damage or paint peeling.  
Pour la clientèle canadienne  
I Do not put objects inside the unit  
Cet appareil numerique de la Classe B est conforme à la norme NMB-003 du  
Canada.  
Make sure that no metal objects or flammable substance get inside  
the camera. If used with a foreign object inside, it could cause a fire,  
short-circuits or damages. If water or a liquid gets inside the camera,  
disconnect the power cord immediately, and consult your dealer or  
a Sanyo Authorized Service Center. Be careful to protect the  
camera from rain, sea water, etc.  
This installation should be made by a qualified service person and should conform to  
all local codes.  
This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to Part 15 of the FCC Rules.  
Features  
I Backlight compensation  
I 1/3-inch CCD solid-state image device (about 410,000  
pixels)  
These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following  
measures:  
I Be careful when handling the unit  
To prevent damages, do not drop the camera or subject it to strong  
shock or vibration.  
I Horizontal resolution of 570 TV lines, S/N ratio of 50 dB min.  
I Minimum required illumination of 0.07 lx (F1.2 lens, 50 IRE)  
I High speed electronic shutter: 1/60 – 1/100,000 sec.  
I Power supply: 24 V AC and 12 – 15 V DC  
I Install away from electric or magnetic fields  
If installed close to a TV, radio transmitter, magnet, electric motor,  
transformer, audio speakers the magnetic field they generate will  
distort the image.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
I Protect from humidity and dust  
Consult the dealer or an experienced radio/TV technician for help.  
To prevent damages to the camera, do not install it where there is  
greasy smoke or steam, where the dampness may get too high, or  
where there is a lot of dust.  
Depending on the conditions of use, installation and environment,  
please be sure to make the appropriate settings and adjustments.  
If you need help with installation and/or settings, please consult  
your dealer.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions: (1) This device may not cause harmful interference, and  
(2) this device must accept any interference received, including interference that  
may cause undesired operation.  
Changes or modifications not expressly approved by Sanyo may void the user's  
authority to operate this camera.  
Printed on recycled paper  
1AC6P1P2706--  
L73R4/US (0503TR-KP-TTC)  
SANYO Electric Co., Ltd.  
Printed in Taiwan  
NAMES AND FUNCTIONS OF PARTS  
TROUBLESHOOTING  
Before sending the camera out for repair, check the items below.  
If the problem persists after checking these items, contact your  
place of purchase or a Sanyo Authorized Service Center.  
SPECIFICATIONS  
Scanning system  
: EIA standard  
<Figure 2. Left view:>  
(525 scanning lines, 30 frames/second)  
: PLL 2:1 interlace  
1 2<Figure 1. Right view:>  
3
<Figure 3. Rear view:>  
6 LENS (lens iris output terminal)  
Interlace  
Image device  
: 1/3-inch solid-state CCD  
: 811 (H) × 508 (V)  
: 768 (H) × 494 (V)  
: External sync (automatic switched)  
Internal sync/Line lock (manually switched)  
: 570 TV lines  
Used to connect the lens plug when the lens is attached.  
Number of pixels  
Number of pixels in image area  
Sync system  
7
F
9
I If no image appears  
Is the power ON?  
Is the coaxial cable attached securely?  
Are the power and voltage normal?  
Is there adequate illumination?  
1Brake coil ()  
3Drive coil (+)  
2Brake coil (+)  
4Drive coil ()  
8
Resolution  
<Figure 3. Rear view:>  
Video output terminal  
Image S/N ratio  
: 1.0 V(p-p)/75 , composite  
: 50 dB min.  
4
5
7 VIDEO OUT (video output terminal: BNC connector)  
Connects to the VIDEO IN (video input) terminal on the peripheral  
equipment.  
Minimum required illumination  
: 0.07 lx approx. (with F1.2 lens, 50 IRE)  
<Figure 2. Left view:>  
I If the image is unclear  
Is the lens in focus? Is the flange back distance adjusted  
correctly?  
Is the lens dirty?  
Dirt or fingerprints on the lens can adversely affect the image.  
Gently wipe any dirt or fingerprints off the lens with a soft cloth or  
lens cleaning paper and cleaning fluid (commercially available).  
Is the monitor adjusted correctly?  
Backlight compensation ON/OFF : Set to ONor OFF”  
6
Auto-iris lens output  
Lens mount  
: DC output (variable DC level), 4-pin terminal  
: CS mount  
8 POWER (power indicator)  
Flange-back  
Auto-iris lens switching  
: 12.5 mm (adjustment range: 0.5 mm)  
: EI/VIDEO/DC  
3
14  
1
2
Lights (red) when the camera power is ON.  
Attachment screw hole diameter : 1/4"-20UNC (top or bottom surface)  
9 GND, AC24V, DC12V (ground terminal, 24 V AC or  
Operating environment  
: Ambient temperature: 10 to +50°C (14 to  
122°F)  
12 V DC input terminal)  
Humidity: 90% RH max.  
: 24 V AC/60 Hz, 12 15 V DC  
: 3.0 W approx.  
F VS IN (External sync composite video signal input  
Power supply  
Power consumption  
Weight  
<Figure 1. Right view:>  
terminal: BNC connector)  
: 245 g approx.  
1 Lens cap  
Protects the lens from damage.  
Accessories  
: Clamping core (1 pc.)  
SERVICE  
The camera is a precision instrument. Handle it carefully and always follow  
the safety precautions. If the camera requires service, never try to repair it  
yourself or open the casing.  
Appearance and specifications are subject to change without prior notice.  
2 Flange-back adjustment dial  
Adjusts the flange-back distance when a zoom lens is attached.  
121.3  
109.5  
57  
0.5  
3 Camera adjustment/setting panel  
Contains camera adjustment dials and setting switches.  
For servicing, maintenance, or repairs, contact your place of purchase or a  
Sanyo Authorized Service Center.  
45  
4 LOCK  
Locking screw for the flange-back adjustment dial.  
9
5 Camera attachment bracket  
Used to attach the camera.  
1/4"-20 UNC  
41.7  
14  
 

QSC Audio Portable Speaker 922dz User Guide
Radio Shack Scanner PRO 2040 User Guide
RCA Car Amplifier M6504 User Guide
Ricoh Welder feeder User Guide
Rockford Fosgate Stereo Amplifier 2501 User Guide
Rotel Stereo Amplifier RA970BX User Guide
Rotel Universal Remote RR 949 User Guide
Samsung Bluetooth Headset GH68 21227A User Guide
Sanyo Power Supply EP91G User Guide
SECO LARM USA Home Security System VG 1C12AQ User Guide