Samsung Washer WT80S0P User Guide

WASHING MACHINE  
Owner’s Instructions  
WT80S0(P)/WT80S1(P)/WT80S2(P)/WT80S2SG  
BEFORE USING THE WASHING MACHINE 1  
PRECAUTIONS  
CONTROL PANEL  
1
1
DESCRIPTION AND CLEANING OF PART 2  
WASHING PROCEDURE  
To Wash  
To Spin Dry  
To Rinsing  
Overflow rinse  
Additional rinse  
INSTALLATION  
Location  
Mounting the legs  
Connecting the drain hose  
LAUNDRY GUIDE  
MAINTENANCE  
TROUBLE SHOOTING  
3
3
3
3
3
4
4
4
4
4
5
5
5
Before operating the washing machine, please read this manual  
thoroughly, and retain it for future reference.  
 
CONTROL PANEL  
BEFORE USING THE WASHING MACHINE CAUTIONS  
0
Remove the cap-hose  
from the drain hose.  
Be sure that the washer is grounded.  
To avoid electrical shock,use a  
metal pipe for the ground  
1.  
WASH TIMMER  
This is used to set the  
wash time, 1-15 minutes.  
15  
12  
3
6
9
connection. But, don't ground the  
washer with gas pipes or telephone  
lines to avoid to dangers of explosion  
or lightning strike.  
WASH TIMER  
In the case of pump drained  
washer, remove  
the cap-hose from  
the drain hole.  
2.CYCLE SELECTOR  
This is used to set the  
Washing/Rinsing  
or Draining.  
Wash/Rinse  
Wash  
Drain Rinse  
Drain  
CYCLE SELECTOR  
CYCLE SELECTOR  
Do not put your hands into the  
spin dryer basket when it is  
spinning.  
Your fingers can be caught by  
spinning laundry and damaged.  
0
3.  
SPIN DRY TIMER  
5
4
1
2
This is used to set the  
spin time, 1-5 minutes.  
PRECAUTIONS WHEN OPERATING  
3
SPIN DRY TIMER  
SELECTOR  
4.WATER  
Don't use excessively hot water.  
(50˚C or more)  
Plastic parts may be deformed or damaged.  
Also, clothing may be deformed or decolored.  
Never allow children to operate  
or play with the washer.  
Children playing with the  
washer may accidentally  
fall into the washing tub.  
During washing, WATER SELECTOR  
KNOB should be selected.  
During spin rinsing, WATER  
SELECTOR KNOB should  
be selected.  
Wash  
Spin  
WATER SELECTOR  
Before washing,check all pockets.  
If nails or pins remain in pockets,they may  
damage the washer or clothes.  
Disconnect the power cord from the  
power supply when not in use.  
5
SELECTOR  
.WASH  
Normal  
Normal  
Heavy Soft  
Heavy  
Soft  
Normal  
Close the water tap a little if the  
water pressure is too high.  
Ventilation opening must not be obstructed  
by carpeting when the washing machine is  
installed on a carpeted floor.  
WASH SELECTOR  
WASH SELECTOR  
WASH SELECTOR  
This is used to select wash action.  
You can wash laundry effectively  
by various methods.  
Never splash water on the control panel.  
If the supply cord of this appliance is  
damaged, it must only be replaced by a repair  
shopappointed by the manufacturer, because  
special purpose tools are required.  
Be sure to cover with the inner  
cover on laundry before spinning.  
This prevents laundry from  
being tossed out and damaged.  
Warning to avoid overfilling and damages this  
appliance must be filled with the operator  
present using a moderate water supply  
pressure only.  
To avoid water splashes, close the  
wash tub lid.  
Be sure laythe drain hose down.  
(in case no drain pump)  
Do not store or use gasoline or other flammable  
vapors and liquids in the vicinity of this or any  
other appliance.  
To avoid overfilling and damages this appliance  
must be filled with the operator present using a  
moderate water supply pressure only.  
 
1
DESCRIPTION AND /CLEANING OF PARTS  
CLEANING THE FILTER  
Pull the overflow filter out and take up  
the filter by removing 3 screws as  
shown in figure. Wash the filter and  
washing tub.  
SPIN DRYER LID  
When you open this  
INNER LID  
lid while the spin basket is  
spinning,the spinning will  
be stopped by the brake  
system.  
DRAIN HOSE  
Push the strainer(filter) out and take  
up the filter as shown in figure.  
Wash the filter and washing tub.  
SPIN DRYER BASKET  
(with pump)  
POWER CORD  
The plug’s shape  
may not be similar to that  
shown in this drawing.  
OVERFLOW  
FILTER  
LINT FILTER  
This is used for  
gathering the  
dregs made  
DRAIN FILTER  
In case of incomplete drain,  
disassemble the drain filter with  
screw driver(+), and remove  
lints from the filter as shown  
in the filter as shown in  
the figure.  
WATER DRAIN HOSE  
(without pump)  
during washing.  
WASH TUB LID  
Be sure to keep  
the lid closed  
EARTH WIRE  
WASH TUB  
during washing  
and spinning.  
HOW TO CLEAN THE FILTER  
(In case drain pump)  
1. Place a rag under the washer filter  
not to wet the floor.  
PULSATOR  
2. Rotate the filter counterclockwise  
and pull out the filter.  
3. Remove dirts and  
DRAIN FILTER  
(with pump)  
CLEANING THE LINT FILTER  
If the dregs are piled up in the  
lint filter after finishing the wash,  
push down and  
OVERFLOW FILTER  
Pull the upper side of the  
overflow filter with  
two fingers inserted into  
hole ‘A’ in the  
OVERFLOW FILTER  
Pull the upper side of the  
overflow filter with your  
fingers into the holes  
in the direction of  
rotate the filter  
clockwise until it  
locks in position.  
A
pull it out as  
direction of arrow  
shown in the  
arrow as shown  
as shown in the figure.  
figure.  
in the figure.  
Wash the filter  
net in water.  
CLEANING THE WASH TUB  
First, fill water in the wash tub to ‘L’ level(  
operating wash cycle for 1~2 minutes. Close the wash tub lid.  
, then drain water from the wash tub simultaneously with  
 
2
WASHING PROCEDURE  
TO WASH  
TO SPIN DRY  
TO RINSING  
1. Before starting to wash, proceed as follows,  
Connect the water supply hose and open  
the water tap.  
1. Transfer the clothes into the  
spin basket and arrange the  
clothes evenly.  
1. Set the cycle selector KNOB to  
‘WASH.RINSE’.  
Wash/Rinse  
Wash  
(In the case of  
Drain Rinse  
Drain  
• Lay the drain hose down toward  
a sinkhole. (In case no drain pump)  
• Place the drain hose in sink or bath.  
(In case no drain pump)  
drain pump  
‘WASH’)  
CYCLE SELECTOR  
CYCLE SELECTOR  
2. Be sure to replace the safety  
cover and close the  
2. Supply the proper amount of water  
so as not to delete one space  
overflow the top of the  
inner lid  
• Connect the power cord to the power  
inner lid.  
0
9
supply outlet.  
safty cover  
washing tub.  
Normal  
15  
3
6
Soft  
Heavy  
2. Set the WASH SELECTOR  
KNOB to the desired mode.  
12  
3. Set the WASH TIMER to  
2~3 minutes.  
WASH TIMER  
WASH SELECTOR  
3. Close the spin  
dryer lid.  
Wash  
Spin  
3. Set the WTER SELECTOR  
KNOB to the desired mode.  
4. Drain the water.  
Set the delete one space  
cycle selector  
Drain  
WATER SELECTOR  
CYCLE SELECTOR  
4. Set the CYCLE SELECTOR KNOB to  
“WASH.RINSE”.(in case drain pump WASH)  
KNOB to ‘DRAIN’.  
0
3
4. Set the SPIN DRY  
TIMER 1-5 minutes.  
5. Repeat this cycle until drain  
water is clean. (2~3 cycles)  
Wash/Rinse  
Wash  
5
4
1
2
Drain Rinse  
Drain  
Rin  
OVER FLOW RINSE  
SPIN DRY TIMER  
CYCLE SELECTOR  
CYCLE SELECTOR  
1. Keep supplying  
Wash/Rinse  
Wash  
water(adjust water  
pressure to ensure  
that the amount of  
Drain Rinse  
Drain  
5. Fill water in the wash tub  
and add the detergent.  
CYCLE SELECTOR  
CYCLE SELECTOR  
water supplied  
does not exceed the amount  
of water drained.)  
6. Load laundry in the  
wash tub and fill water  
to proper water level.  
0
15  
12  
3
6
0
2. Set the WASH TIMER  
6~8 minutes.  
15  
12  
3
6
7. Set the WASH TIMER  
1-15 minutes.  
9
WASH TIMER  
0
3. As soon as the  
WASH TIMER  
shuts off, turn off  
the water tap.  
9
15  
3
WASH TIMER  
8. After washing, set the CYCLE  
SELECTOR KNOB  
12  
6
Drain  
9
to 'DRAIN' for drain.  
WASH TIMER  
CYCLE SELECTOR  
4. Set the CYCLE  
SELECTOR KNOB  
to ‘DRAIN’.  
Drain  
CYCLE SELECTOR  
 
3
INSTALLATION  
ADDITIONAL RINSE  
LOCATION  
CONNECTING THE DRAIN HOSE  
1 After rinsing you can select this  
course for more effective rinse  
(Don't just select this course  
for rinse.) Load the laundry  
evenly into the spin basket.  
Leave some space of  
at least 15cm between the washing machine  
and the wall.  
Place the washing machine on a sturdy flat surface.  
If the washing machine is placed on an uneven  
or weak surface, noise or vibration may occur.  
(Allowable is 2˚)  
After attaching the connector ring(a), insert the  
drain hose(b) in the draining direction.  
a
b
2 Set the WATER SELECTOR  
KNOB to SPIN and  
Never install the washing machine near water.  
Do not place the washing machine in steamy CONNECTING THE DRAIN HOSE  
Drain  
Wash  
Spin  
CYCLE SELECTOR  
KNOB to DRAIN.  
room or where the washing machine is directly 1. Before connecting the drain hose, remove  
CYCLE SELECTOR  
WATER SELECTOR  
exposed to rain.  
the cover (a) from the drain hole.  
3 Supply water for about 1 minute.  
Adjust the water flow to prevent  
overflow from the wash tub.  
Moisture may damage electrical insulation and 2. After pressing the joint ring (b), insert the  
cause an electrical shock to occur.  
Avoid direct sunlight or heating devices.  
As plastic and electrical components are  
affected by direct heat, never place the washing  
machine near heaters, boilers, etc., or under direct  
sunlight.  
drain hose(c) to drain direction.  
4 After completing the water supply,  
(a)  
inner lid  
cover the laundry with  
(C)  
(C)  
safety cover and close  
the inner lid.  
safety  
cover  
(b)  
(b)  
(In case of pump  
drained washer)  
Install the drain hose  
5 Close the spin dryer lid.  
about 70~80cm above  
the ground for pump model.  
0
CHANGING THE POSITION OF THE  
DRAIN HOSE  
6 Set the SPIN DRY  
TIMER 2~3 minutes.  
5
1
2
MOUNTING THE LEGS  
Before attempting to change the position of the  
4
Lay down the washer with its back facing  
downward. Insert four legs into the leg mounting  
sections of the base corners of the main body.  
3
drain hose, disconnect the plug from the outlet.  
1. Route the drain hose inside the machine.  
2.Take out the drain hose from the opposite hole  
and insert the drain hose into the hose holder.  
SPIN DRY TIMER  
Claw  
Insert the claw of the  
leg with the square  
hole of the leg  
Square  
hole  
2
1
mounting section,  
and push the leg in  
the arrow direction  
2
1
as shown in the  
Leg  
Bottom face of  
main body  
figure until it clicks.  
Hose holder  
 
4
LAUNDRY GUIDE  
MAINTENANCE  
TROUBLE SHOOTING  
TO LOAD THE LAUNDRY INTO  
THE SPIN BASKET.  
Press the laundry evenly and put the safety  
cover into the spin basket as shown in the figure.  
WASHING TIME  
TROUBLE  
CHECK POINT  
WASHING  
SELECTION  
WASHING TIME  
TYPE OF CLOTHING  
The washing  
machine does properly connected to a power  
not work.  
Check that the power cord is  
10 to15 minutes  
Extremely soiled  
heavy fabric  
outlet. Is there a power failure?  
NORMAL  
Clothes do  
Is the machine overloaded?  
not move freely.  
8 to10 minutes  
7 minutes  
Linen, cotton, etc.  
Is the laundry arranged  
evenly?  
Incomplete  
spinning  
Ordinary clothes  
(underwear,etc)  
Slightly soiled  
synthetic fiber  
Is the filter clogged with lint?  
See cleaning of parts.  
Incomplete  
draining  
2 to 5 minutes  
SOFT  
100% wool, mixed wool knitting,  
thin synthetic fiber with  
2 to 5 minutes  
TO RETRIEVE THE CLOTHING THAT HAS  
FALLEN BETWEEN THE BASKET AND TUB.  
For safety reason, pull the power supply plug  
out of the socket.  
1. Unscrew the spin dryer hatch.  
2. The spin dryer hatch is  
Is the spin dryer lid closed  
completely?  
Are laundry items (socks, etc.) falling  
out of the spin dryer basket and  
clinging to the axle?  
tags indicating hand washing  
The spin dryer  
basket will not  
run.  
SPIN DRY TIME  
TYPE OF FABRIC  
Thin (synthetic fiber)  
TIME  
1 min.  
See To retrieve...on page 5.  
fixed to the brim by the  
concave and convex  
parts at two places.  
Expand the concave and  
wool  
cotton  
1~2 min.  
3~5 min.  
5 min.  
AFTER OPERATION  
1. Remove the power cord from the outlet.  
2. Take out the laundry.  
thick (cotton)  
convex parts,and pull up  
the spin dryer hatch to  
3. Close the water tap and disconnect the water  
supply hose.  
DETERGENT  
WATER  
LEVEL  
AMOUNT OF  
DETERGENT  
remove it.  
3. Retrieve the clothing.  
4. Close the spin dryer hatch. Push the hatch  
firmly until the catch at the front is securely  
attached.  
4. Clean the washing machine.  
- Periodical cleaning will extend the life of your  
washing machine.  
- Do not spray the unit water or use tinner, benzene,  
alcohol etc, for cleaning it.  
The amount of detergent  
is average. Follow the  
instruction printed on the  
package for amount of  
detergent. Choose the  
amount of detergent  
Low (37l)  
37g  
45g  
54g  
Medium(45l)  
High (54l)  
according to the fabric type.  
DETERGENT  
In case the water level is at High,  
amount of water is 42l.  
-H-  
Follow the directions printed on the package  
for amount of detergent. Choose the amount of  
detergent depending on the fabric type and  
water level.  
CLEANING THE WASHING MACHINE  
Wipe off stains on the cabinet and operation pane  
with a soft cloth. Neither use benzene, thinner,  
cleanser, or wax, nor scrub the washing machine  
with a brush. Painted surfaces or plastic parts will  
be damaged.  
 
5

Reliance Water Heaters Water Heater RUF 100 199 SERIES 100 User Guide
RocketFish Conference Phone RF QS2 T User Guide
Rosewill Server RSV L4000 User Guide
Sagem Cell Phone MyX2 2 User Guide
Samson Stereo Amplifier BASS PRE AMP User Guide
Samsung Cell Phone GH68 04434A User Guide
Sansui Flat Panel Television HDLCD1900A User Guide
Sanyo CRT Television AVM 3650G User Guide
Sanyo Vacuum Cleaner SC B1211 User Guide
Sears Blower 257796382 User Guide