Samsung Universal Remote RMB4 User Guide

User guide type 35104373  
RMB4  
User guide, English  
OneRemote RMB4 controller installed in a Bang & Olufsen Beo4 remote control.  
Operate these devices using the modified Beo4:  
Samsung LED TV 7-series and other.  
Operate devices that are operate able with RCU’s like:  
Samsung most remotes for Samsung digital TV.  
 
Congratulations  
With the OneRemote controller installed inside your Bang & Olufsen Beo4  
remote control, you can fully operate your non B&O TV with this terminal.  
This guide explains how.  
If your Beo4 has already been correctly set up, you can now proceed to one  
of the two operation tables:  
Page 9  
If your Beo4 has enabled Navi buttons . *1  
Page 8  
In any other case.  
Important ! !  
If the OneRemote controller has not yet been optimized for your setup,  
refer to the installation section about the initial setup and option program-  
ming. There is no programming needed during everyday use.  
The OneRemote controller that has been installed inside your Beo4 remote  
control, can be used in any Beo4 remote control. Both first generation mod-  
els and the latest with extra buttons for manoeuvring, the Beo4 Navi.  
To get the most of your modified Beo4, the OneRemote controller must be  
programmed according to the Beo4 model and the environment that your  
TV is a part of. Refer to page 5 and forward, for the initial setting.  
*1 Extra buttons have been added on never Beo4 models, Beo4 Navi. Se page 10.  
3
 
The OneRemote controller for the Beo4 remote control  
The OneRemote controller is a small microcomputer module, which is specifically  
made to be built in to a Bang & Olufsen Beo4 remote control.  
The controller captures the commands that were meant for operating a Bang & Olufsen  
device. Before the commands are emitted from the Beo4, these commands are convert-  
ed, and therefore also able to operate a non Bang & Olufsen TV.  
Each controller is dedicated for operating a specific product like an Apple iPod docking  
station, a flat screen TV, a curtain controller etc.  
The controller makes the Beo4 able to operate a third part device, still able to operate  
any other Bang & Olufsen products.  
If there is a Bang & Olufsen audiomaster in the room, it can be used for handling the sound. Speakers con-  
nected to an audiomaster are of a much better quality than the speakers in a TV. In a B&O linkroom setup  
with Beolink Active or Beolink Passive, you can also use these speakers to improve sound from most TV’s.  
Only a simple audio cable is needed between the TV and the audiomaster. See the option programming sec-  
tion about AAUX and PC modes on page 11.  
4
 
Operating with OneRemote.  
To be able to operate the non B&O TV optimal using the OneRemote modified Beo4,  
the user has to be familiar with the operations available when using the original remote  
control, as described in the TV’s user manual.  
A beo4 remote control is not equipped with as many keys as most remote controls for  
non B&O devices. We have designed an operation ‘layout’ that works logically, even  
when shifting between different OneRemote operated devices. To get a common layout  
for many devices, we therefore needed to redefine a few of the beo4 buttons to other  
functions.  
The Beo4 Navi model introduces new buttons, making it easier to make operation  
table’s, closer to the TV’s own.  
Coloured function buttons.  
To make room for easy access to more important functions, in some layouts we have  
moved the coloured function buttons, to a lower layer. In these layouts to send a ‘color’  
command, a O must be pressed before the coloured button itself.  
This way we are able to assign other functions to the coloured buttons in direct mode.  
In a OneRemote environment the coloured buttons are often assigned to these opera-  
tions:  
Guide, EPG or similar.  
Q
Back, Backup, Return or similar.  
E
Programme zapping. P+/ P- ,  
Channel up/ down or CH+/ CH-.  
W
R
Go, Navi or Stop shifted operation.  
Some of the buttons has two or three operations. To get to these they have to be preced-  
ed with O or q.  
In case of Beo4 Navi a p button has been a added to replace the O button, when  
in ‘mode 2’. In mode 2 the OneRemote uses the Center button for shifting, instead of  
O . Refer to page 10.  
Buttons that has been assigned secondary functions are listed in the operating table on  
page 9.  
5
 
Programme stepping, up/ down manoeuvring in menus.  
Most set top boxes and TV’s has 4 arrow buttons for manoeuvring in on-screen menus,  
up, down, left and right. In addition they are equipped with separate programme step-  
ping buttons for zapping through the programme list. Often these keys are named P+, P  
-, CH+ or CH-.  
OneRemote often makes use of the R and the W keys for programme zap-  
ping. This way the four up, down, left and right buttons are free to be used for the more  
natural use of manoeuvring in on screen menus.  
Using a Beo4 Navi in mode 2, manoeuvring in On-screen menus is fully handled using  
the added ‘joy-stick’, not available on previous Beo4 models. In a Beo4 Navi setup we  
therefore can make use of the up and down arrows for programme zapping.  
Setting the Zap Mode Option  
If the OneRemote controller is not set to operate in Navi mode, the Beo4 but-  
tonsW and R are used for programme stepping. The D and Fbuttons  
are used to manoeuvre up and down in an on-screen menu. This is the default factory  
setting, as described above.  
Selecting the Zap mode buttons:  
Enter one of these 2 codes within 10 seconds to set the preffered Programme Zap mode buttons.  
The D and F buttons will be used for pro-  
LIGHT  
LIGHT  
m
q
9
0
p
p
gramme zapping.  
The W & R buttons will be used for pro-  
m
q
9
1
gramme zapping.  
6
 
Disabling and Dual TV Option  
The OneRemote controller in the modified Beo4 remote control can be enabled or disa-  
bled using this option. When disabled the Beo4 remote control operates as a Beo4 that  
has not been modified.  
In DUAL TV-mode the OneRemote controller enables operation of both a B&O TV and  
the non B&O TV which the controller is made to operate.  
Disabling and Dual TV mode:  
Enter one of these 3 codes within 10 seconds to set the preffered mode.  
Disables the OneRemote controller.  
LIGHT  
LIGHT  
m
q
2
0
p
p
Enables the OneRemote controller.  
m
q
2
1
Enables the OneRemote controller in Dual TV mode.  
LIGHT  
m
q
2
2
p
In this mode:  
t + 1 starts operating a B&O TV.  
t + 2 starts operating the non B&O TV  
7
 
Translation table when not in Navigation mode. * see page 10  
Daily operation  
Text TV operation  
t
w
Turns on the TV  
Turns off the TV  
TEXT  
Text TV on/ mix  
Text TV off  
t
O
O
Enter  
W
*
1
*
2
P
r
o
g
+
TTV page+  
Playback operations  
R
*
1
*
2
P
r
o
g
-
TTV page -  
o
q
o
Play press 1 sec.  
Stop  
Pause  
Q *1*2 Guide  
E *1*2 Return  
q
q
TTV Hold  
TTV Index  
o
A
/
S
R
e
w
/
F
F
e
m
o
Exit  
Source  
Menu  
r
Record  
m
Other operations  
O
O
O
O
O
O
O
O
1
2
3
4
5
6
7
9
FAV  
Channal list  
info  
TTV Hide  
TTV Show  
TTV Size  
Tools  
Content  
Subtitle  
Media Play  
Internet  
*1 The up/ down arrow operations can be ex-  
changed with the blue and yellow buttons. See  
page 6.  
*2 As the direct function of the coloured func-  
tion buttons has been assigned to other func-  
Special/ alternative operations  
tions, these have to be preceded with a  
o
to retrieve the actual coloured function.  
O
O
O
0
8
e
Play  
Record  
3D  
o
o
o
o
Q
W
E
R
Green function  
Yellow function  
Red function  
q
e
AD  
Blue function  
8
 
Translation table when in Navigation mode. * see page xxxxxx  
Daily operation  
Text TV operation  
t
w
Turns on the TV  
Turns off the TV  
TEXT  
Text TV on/ mix  
Text TV off  
t
O
O
Enter  
D
A
F
S
CH+ / CH-  
REW / FF  
Playback operations  
p
q
o
Play  
Stop  
Pause  
Navi buttons are used for manoeuvring in on-  
screen menus.  
q
q
r
Record  
W
R
Q
E
Yellow key  
Blue key  
Green key  
Red key  
Other operations  
O
O
O
O
O
O
O
O
1
2
3
4
5
6
7
9
FAV  
Channal list  
info  
e
BACK  
m
Exit  
TTV Hide  
TTV Show  
TTV Size  
Back  
Source  
Menu  
Tools  
o
m
TTV Index  
Content  
Subtitle  
Media Play  
Internet  
o
o
o
o
Q
W
E
R
EPG  
CH List  
PRE CH  
TOOLS  
Special/ alternative operations  
O
8
e
Record  
3D  
O
q
e
AD  
9
 
Beo4 NAVI mode option.  
Newer Beo4 models are named Beo4 Navi due to an added special navigation button.  
A joystick type control button, placed where previous Beo4 models have a Obutton.  
If your Beo4 has a O button, this chapter is not relevant for you !  
Use of the Beo4 Navi joystick navigation operation:  
Enter one of these 2 codes within 10 seconds to enable or disable the OneRemote controllers use of the ex-  
Set the Beo4 Navi remote control in operation mode 2, as described in the B&O user guide that was sup-  
plied with your Beo4, if you want to use these. Otherwise select mode 1.  
Enable use of the NAVI control.  
LIGHT  
LIGHT  
m
q
5
1
p
When the OneRemote controller NAVI mode has been  
enabled, use the operation table on page 9.  
Disable use of the NAVI control.  
When the OneRemote controller NAVI mode has been  
m
q
5
0
p
disabled, use the operation table on page 8.  
10  
 
Setting the OneRemote Volume Option  
When the TV mode is selected by pressing the t button, it automatically powers  
on the TV and turns on the picture.  
But often the sound is lead to external speakers at-  
tached to a B&O audiomaster or another amplifier.  
This option set the way that the OneRemote handles  
volume in TV mode.  
This option also can power on other B&O devices  
than the TV, when t is selected. Audio is then  
typically fed from the TV to the audiomaster from  
using a Line to Datalink cable. Moving the TV sound  
to the speakers of the audiomaster, significantly im-  
proves the sound quality.  
Volume options  
Sound destination Volume control  
Volume disabled  
The non B&O TV  
No volume regulation  
Non B&O TV format  
AAUX in B&O format  
PC in B&O format  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
m
m
m
m
m
m
q
q
q
q
q
q
0
0
0
0
0
0
0
1
2
3
4
5
p
p
p
p
p
p
AAUX *1  
PC *2  
AAUX in B&O format  
AAUX in B&O format  
AAUX + 6 *3  
AAUX +  
7
*
*
3
*1 When t is pressed your Beo4 it sends a Power On command to your TV. At the same the Beo4 sends  
a AAUX command to a Bang & Olufsen audiomaster.  
Until another source is selected, volume commands will be directed to the B&O audiomaster.  
*2 When t is pressed your Beo4 it sends a Power On command to your TV. At the same the Beo4 sends  
a
c
c
o
m
m
a
n
d
t
o
a
B
a
n
g
&
O
l
u
f
s
e
n
s
y
s
t
e
m
.
Until another source is selected, volume commands will be directed to the B&O system.  
*3 When t is pressed your Beo4 it sends a Power On command to your TV. At the same the Beo4 sends  
a AAUX + 6 or 7 command to a Bang & Olufsen linksystem.  
Until another source is selected, volume commands will be directed to the B&O linksystem.  
11  
 
The Beo4 VMEM / VTAPE button option  
On your OneRemote modified Beo4 remote control, the VMEM button can be pro-  
grammed, to open a specific source on your non B&O TV.  
VMEM/ VTAPE options  
Enter one of these codes within 10 seconds, to select the source on the non B&O TV that will be selected  
with the VMEM or VTAPE button.  
No new source selected.  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
m
m
m
m
m
m
m
m
m
m
T
T
T
T
T
T
T
T
T
T
0
1
2
3
4
5
6
7
8
9
1
1
1
1
1
1
1
1
1
1
p
p
p
p
p
p
p
p
p
p
The AV1 socket on the TV is opened.  
The AV2 socket on the TV is opened.  
The DTV tuner on the TV is opened.  
The Component 1 socket is shifted to.  
The Component 1 socket is accessed.  
The HDMI 1 socket is accessed.  
The HDMI 2 socket is accessed.  
S-VHS 1  
USB Wiselink  
As the OneRemote controller is able to operate many different TV models, there might be some sources in the  
table, that is not available on your TV. The only way to find out if your TV accepts these codes, is testing  
each of the options.  
If a source is not access able using these options, sources must be accessed the same way as using the TVs  
original remote control. Using the source button.  
12  
 
The Beo4 DTV/ SAT button option  
On your OneRemote modified Beo4 remote control, the DTV/ SAT button can be pro-  
grammed, to open a specific source on your non B&O TV.  
DTV/ SAT options  
Enter one of these codes within 10 seconds, to select the source on the non B&O TV that will be selected  
with the DTV/ SAT button.  
No new source selected.  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
m
m
m
m
m
m
m
m
m
m
f
f
f
f
f
f
f
f
f
f
0
1
2
3
4
5
6
7
8
9
1
1
1
1
1
1
1
1
1
1
p
p
p
p
p
p
p
p
p
p
The AV1 socket on the TV is opened.  
The AV2 socket on the TV is opened.  
The DTV tuner on the TV is opened.  
The Component 1 socket is shifted to.  
The Component 1 socket is accessed.  
The HDMI 1 socket is accessed.  
The HDMI 2 socket is accessed.  
S-VHS 1  
USB Wiselink  
As the OneRemote controller is able to operate many different TV models, there might be some sources in the  
table, that is not available on your TV. The only way to find out if your TV accepts these codes, is testing  
each of the options.  
If a source is not access able using these options, sources must be accessed the same way as using the TVs  
original remote control. Using the source button.  
13  
 
The Beo4 DVD button option  
On your OneRemote modified Beo4 remote control, the DVD button can be pro-  
grammed, to open a specific source on your non B&O TV.  
DVD options  
Enter one of these codes within 10 seconds, to select the source on the non B&O TV that will be selected  
with the VMEM or VTAPE button.  
No new source selected.  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
m
m
m
m
m
m
m
m
m
m
d
d
d
d
d
d
d
d
d
d
0
1
2
3
4
5
6
7
8
9
1
1
1
1
1
1
1
1
1
1
p
p
p
p
p
p
p
p
p
p
The AV1 socket on the TV is opened.  
The AV2 socket on the TV is opened.  
The DTV tuner on the TV is opened.  
The Component 1 socket is shifted to.  
The Component 1 socket is accessed.  
The HDMI 1 socket is accessed.  
The HDMI 2 socket is accessed.  
S-VHS 1  
USB Wiselink  
As the OneRemote controller is able to operate many different TV models, there might be some sources in the  
table, that is not available on your TV. The only way to find out if your TV accepts these codes, is testing  
each of the options.  
If a source is not access able using these options, sources must be accessed the same way as using the TVs  
original remote control. Using the source button.  
14  
 
The Beo4 VAUX button option  
On your OneRemote modified Beo4 remote control, the VAUX button in the List-  
menu can be programmed, to open a specific source on your non B&O TV.  
VAUX options  
Enter one of these codes within 10 seconds, to select the source on the non B&O TV that will be selected  
with the VMEM or VTAPE button.  
No new source selected.  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
LIGHT  
m
m
m
m
m
m
m
m
m
m
a
a
a
a
a
a
a
a
a
a
0
1
2
3
4
5
6
7
8
9
1
1
1
1
1
1
1
1
1
1
p
p
p
p
p
p
p
p
p
p
The AV1 socket on the TV is opened.  
The AV2 socket on the TV is opened.  
The DTV tuner on the TV is opened.  
The Component 1 socket is shifted to.  
The Component 1 socket is accessed.  
The HDMI 1 socket is accessed.  
The HDMI 2 socket is accessed.  
S-VHS 1  
USB Wiselink  
As the OneRemote controller is able to operate many different TV models, there might be some sources in the  
table, that is not available on your TV. The only way to find out if your TV accepts these codes, is testing  
each of the options.  
If a source is not access able using these options, sources must be accessed the same way as using the TVs  
original remote control. Using the source button.  
15  
 

Q See Security Camera QSDS4936D User Guide
RAD Data comm Network Card ASMi 31 User Guide
Radio Shack Cordless Telephone ET 557 User Guide
RCA Clock Radio RP 3761 User Guide
RCA CRT Television J20F635 User Guide
RCA Flat Panel Television J20L743 User Guide
RTS Stereo Receiver RKP 4 User Guide
RuggedCom Weather Radio RMC40 User Guide
Samsung DVD Player AK68 00052F User Guide
Samsung Personal Computer 795MB+ User Guide