OUTDOOR HOUSING
SHG-220/SHG-220S
Installation Manual
GB
D
F
Instalationshandbuch
Manuel D’installation
Manual De Instalación
E
C
J
K
FCC & ICES INFORMATION (U.S.A.AND CANADIAN MODELS ONLY)
WARNING - This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry
Canada. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential installation. This equipment
generates, uses, and radiates radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the interference at
his own expense. Intensional or unintensional changes or modifications not expressly
approved by the party responsible for compliance shall not be made. Any such changes
or modifications could void the user’s authority to operate the equipment.
GB
If necessary, the user should consult the dealer or an experienced radio/television
technician for corrective action. The user may find the following booklet prepared by the
Federal Communications Commission helpful: "How to Identify and Resolve Radio-TV
Interference Problems." This booklet is available from the U.S. Government Printing
Office, Washington, DC 20402, Stock No.004-000-00345-4.
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This label may appear on the bottom of the unit due to space limitations.
The lightning flash with an arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
2
Summary
The Outdoor Housing (SHG-220/SHG-220S) is used for installating
the Smartdome Camera on an outdoor wall or ceiling.
Precautions Before Installation
Make sure that the proposed location can support the combined weights of the
•
Corner Mounted Adaptor, Wall Mounted Adaptor, Outdoor Housing and Smartdome
Camera (about 11 kg).
Use a 24V AC, 3.0 A power adaptor.
•
This goods should only be installed by a qualified technician using approved materials
•
and wiring practices in accordance with national, state, and local electrical code.
Installation
Select a location that is capable of supporting four times the
total weight of the product to be installed.
1
Depending on the installation location, use the appropriate
adaptor for installing the Outdoor Housing.
2
1. Wall Mounted Adaptor (SADT-100WM): For direct installation on a wall.
2. Ceiling Mounted Adaptor (SADT-100CM): For installation on a ceiling.
3. Pole Mounted Adaptor (SADT-100PM): For installation on a cylindrical pole.
• The Wall Mounted Adaptor (SADT-100WM) is also used in conjunction with
the Pole Mounted Adaptor.
4. Corner Mounted Adaptor (SADT-110CM): For installation in the corner of a wall.
• The Wall Mounted Adaptor (SADT-100WM) is also used in conjunction with
the Pole Mounted Adaptor.
3
Connect the Outdoor Housing power cable to the camera
adaptor's AC 24V-out connector.
3
HOUSINMG
GB
CAMERA ADAPTOR
Connect the power cable, video-out cable and
communications cable to the camera adaptor.
(For details, refer to the Smartdome Camera User's Guide.)
4
5
After tidying up the cables, align the camera adaptor lever
with the cover top boss and fasten it to the cover top using
four screws (M4 x 8).
CAMERA ADAPTOR
Boss
LEVER
4
Disengage the dome from the Smartdome Camera.
1) Loosen the (M2) screw on the side of Smartdome Camera, turn the dome
clockwise about 15 degrees and pull it off.
6
SMARTDOME CAMERA
DOME
15 degree
Align the arrow on the camera adaptor with the arrow on the
Smartdome Camera, insert the three bosses on the back of
the camera into the three camera adaptor holes, together with
the connectors, and turn the camera about 15 degrees
clockwise. (Listen for the click that confirms engagement and
make sure that the locking lever returns to its original
7
position.)
CAMERA ADAPTOR
CAMERA ADAPTOR
2
CAMERA
1
CAMERA
15 degree
5
Secure the camera body to the camera adaptor using the screw (BH
8
M3
x
L8) provided with the Smartdome Camera.
• To disengage the camera from the camera adaptor, loosen the engaging screw
(BH M3 x L8), turn the camera counterclockwise while the locking lever is
turned clockwise, and pull the camera off.
GB
For smooth assembly of the dome, apply silicon grease to the
gasket, align it with the boss and push the dome vertically
into the housing.
9
GASKET
(GREASE
APPLICATION)
DOME
6
Insert three pins into the side of the Housing and insert the
screws (M3 L12) into the pins from below.
10
x
PIN
Product Specifications
External dimensions:
ø 266 x H259
1 1/2" NPT PIPE THREAD
Weight: 3.7kg
Suitable Temperature range:
- 40°~ 50°C
Suitable Humidity range:
0~100%
Fan operating temperature:
45°C or higher
Heater operating temperature:
10°C or less
172
259
168
266
7
Accessories
..........................
........................................................
Screw(BH M3 X L12)
PIN
3
3
1
........................
SILICON GREASE 5g
GB
8
AB68-00235A
PRINTED IN KOREA
|