Samsung Camera Lens AD68 01762A User Guide

 
FOR SAFE USE OF YOUR LENS  
Although we have carefully designed these lenses for safe operation, please pay special  
attention to items marked with the following symbols when using this product.  
This symbol indicates precautions that if not followed,  
WARNING  
CAUTION  
could result in serious injury to the user.  
This symbol indicates precautions that if not followed,  
could result in minor or medium injury to the user or  
damage to the equipment.  
WARNING  
Never look at the sun through the lens or camera. Serious damage to the retina or total loss of  
eyesight may occur.  
CAUTION  
Do not leave the lens in direct sunlight without lens caps. Direct sunlight passing through the  
lens will be intensified, and should it focus on flammable materials, fire may occur.  
 
1》  
PRECAUTIONS AND LENS MAINTENANCE  
1. Storage and mildew prevention  
Take the lens out of the protective case or camera bag, and store it in a dry, well-ventilated place.  
• Avoid storing the lens in a poorly ventilated location such as a closet, wardrobe, drawer, vehicle,  
or where insect repellent or medicine is kept.  
• Avoid storing the lens in areas of high temperature and humidity, where there is a risk of mildew  
growth. Store the lens with a desiccant in a dry cabinet, airtight container, or plastic bag.  
(Leaving a saturated desiccant in the storage container can cause damage to the lens. Be sure  
to read the instructions that come with the desiccant before use.)  
2. The lens is not waterproof. When using the lens in a rain or mist, be careful not to allow it to get wet.  
3. Never use any organic solvent such as thinner, alcohol, or benzine, etc. to remove dust on the lens.  
4. The lens is a precise optical instrument. Be careful not to let it fall, or subject it to strong shocks or  
pressure. Use a cushion or similar pad to protect the lens from the vibrations of motorcycles or other  
vehicles, boats, etc.  
5. Avoid subjecting the lens to rapid changes in temperature, otherwise condensation can occur on  
both the inside and the outside of the lens. Put the lens in a plastic bag or camera bag, and take it  
out after the lens has reached ambient temperature.  
6. When the lens is not attached to the camera body, attach both the supplied lens cap and lens  
mountcap to protect it from dust.  
7. Do not leave the camera with the lens cap off attached to a tripod or other rigid camera support.  
The inner parts of the camera can be damaged by direct sunlight.  
8. Have the lens inspected by a dealer every one or two years to maintain its high performance.  
 
2》  
CONTENTS  
FOREWORD  
FOR SAFE USE OF YOUR LENS ...........................................................................................1  
PRECAUTIONS AND LENS MAINTENANCE..........................................................................2  
Schneider D-XENON LENS .....................................................................................................4  
About the lens mount...............................................................................................................5  
MOUNTING AND REMOVING THE LENS ..............................................................................7  
LENS CAP................................................................................................................................8  
FOCUSING...............................................................................................................................9  
Changing the Focus Mode ......................................................................................................9  
Focusing with the OK Button.................................................................................................10  
Focusing with the AF Button..................................................................................................10  
Using the Quick-Shift Focus System (GX -series cameras only)..........................................12  
APERTURE CONTROL..........................................................................................................14  
MACRO LENS........................................................................................................................15  
ATTACHING THE LENS HOOD .............................................................................................17  
FILTERS .................................................................................................................................18  
PRECAUTIONS WHEN USING THE LENS WITH A FLASH ................................................19  
MAIN SPECIFICATIONS........................................................................................................20  
 
3》  
Schneider D-XENON LENS  
Focusing ring  
Front-ring threads  
Distanceꢁscale  
Aperture ring  
Aperture-A-lock button  
Depth-of-field scale  
NOTE :  
Aperture settings are controlled automatically as if set to the auto "A" position, so  
accessories without an auto "A" setting cannot be used with these lenses.  
 
4》  
About the lens mount  
The D-XENON lenses are primarily designed to work with the SAMSUNG autofocus DSLR  
(KAF or KAF2-mount camera), making autofocus shooting possible. When Zoom lenses with  
power  
zoom function are used on the SAMSUNG KAF2-mount camera, the camera features a  
Power Zoom system.  
Mounts of Lenses without the power zoom function are KAF.  
KAF mount  
KAF2 mount  
Power zoom  
contacts  
AF coupler  
Lens-information contacts  
 
5》  
Lens Mount Compatibility  
D-XENON lens mount compatibility chart is shown below.  
CAUTION:  
KAF2-mount  
which is equipped with  
Be careful not to damage or dirty the  
lens-information contacts and AF cou-  
pler on the mount surfaces of the  
camera and lens. Otherwise, failure or  
malfunctionmay occur.  
Power contacts  
AF coupler  
Lens information contacts  
KAF-mount  
which is equipped with  
AF coupler  
Lens information contacts  
KA-mount  
which is equipped with  
Lens information contacts  
K-mount  
(base mount)  
 
6》  
MOUNTING AND REMOVING THE LENS  
1
2
1. To mount the lens on the camera body  
Attach the lens while aligning the red dots on the lens and body, then turn the lens  
clockwise until it clicks in place.  
Memo:  
Do not hold down the lens unlock button while mounting the lens, otherwise the lens  
will not be properly mounted.  
After mounting the lens, gently turn the lens counterclockwise to make sure it is locked  
2. iTnoprlaecme.ove the lens  
Hold down the lens unlock button on the camera body and turn the lens  
counterclockwise.  
 
7》  
LENS CAP  
Take off the lens cap by pressing the two tabs inward as shown above.  
2. Memo:  
When not using the lens, be sure to attach the lens cap.  
 
8》  
FOCUSING  
1
Changing the Focus Mode  
Use the cameras focus mode switch to change between the autofocus mode (SAF,  
CAF) and manualfocus mode. For details, refer to your cameras manual.  
1. Using Autofocus  
Set the cameras focus mode to autofocus (SAF, CAF). Press the shutter button  
halfway to autofocus.  
 
9》  
Focusing with the OK Button  
With the GX-1S/1L camera set as explained below, auto focusing by pressing the  
shutter button halfway will be disabled and the OK button can be used instead to auto  
focus. On the [C Custom menu], select [Enable AF] for [OK btn when shooting].  
Focusing with the AF Button  
With the GX-10 camera set as explained below, auto focusing by pressing the shutter  
button halfway will be disabled and the AF button can be used instead to auto focus.  
On the [CUSTOM1 MENU] menu, select [Enable AF] for [AF Button Function].  
2. Memo:  
For details on the setting procedure, refer to the camera’s instruction manual.  
CAUTION  
During autofocusing, the focusing ring will rotate. To prevent malfunction, do not  
touch the focusing ring during autofocusing.  
 
10》  
2
2. Using Manual Focus  
Set to MF with the camera’s focus mode, and turn the focusing ring to focus manually.  
 
11》  
Using the Quick-Shift Focus System (GX -series cameras only)  
If you use the lens with an GX -series camera and the focus mode is set to autofocus,  
you can focus manually after autofocus is achieved. Just turn the focusing ring to  
manually touch-up the focus. You can do this without changing the focus mode to MF.  
How to use the Quick-Shift Focus System  
1. Using Autofocus  
Set the camera’s focus mode switch to autofocus, then press the shutter button  
halfway to autofocus.  
With the GX camera set as explained by “Focusing with the OK Button” on page 9,  
you can focus by pressing the OK button.  
2. Hold down the shutter button halfway (or hold down the OK button) and  
then turn the focusing ring to focus.  
You can focus the subjec with the OK button (GX-1S / 1L) and the AF button (GX-10).  
3. Finally, press the shutter release button fully to take a picture.  
 
12》  
CAUTION  
During autofocusing, the focusing ring will rotate. To prevent malfunction, do not  
touch the focusing ring during autofocusing.  
When using the Quick Shift Focus System, keep pressing the shutter button  
after you achieve focus before taking a picture. If you let go of the shutter  
button before taking the picture, you will have to focus all over again when  
you press the shutter button again. In the following cases, you can take the  
picture without autofocusing after letting go of the shutter button.  
With the GX-1S/1L camera, use the [C Custom] menu to set [Cancel AF] for  
[OK btn when shooting]. This will enable you to focus manually while you  
hold down the OK button. The setting procedure and more details are  
explained in the camera’s instruction manual.  
With the GX-10 camera, use the [CUSTOM1 MENU] menu to set [Cancel AF]  
for [AF Button Function]. This will enable you to focus manually while you  
hold down the AF button. The setting procedure and more details are  
explained in the camera’s instruction manual.  
 
13》  
APERTURE CONTROL  
32  
2
2
A
1
6
11  
16 11  
8
2
8
5.6  
2
5
.6  
Setting the aperture to "A"(Auto) Turn the aperture ring to align the aperture-A index with  
the line while depressing the Aperture-A-lock button. The aperture ring can be released  
from "A" in the same manner to set your desired f-stop manually.  
 
14》  
MACRO LENS  
D-XENON Macro 100mm lenses enable closeup photography up to 1x magnification.  
Clamp Switch  
Magnification Scale  
The magnification is indicated by denomi-  
nators on the distance scale. “1” indicates  
“1x”. For example, “1” on the magnification  
scale at the top will make the magnification  
1/1x. If you want to set the magnification  
first, turn the focusing ring to set the  
desired magnification. Then focus the sub-  
ject by moving the camera forward or back.  
 
15》  
About the Clamp Switch  
The D-XENON Macro 100mm lenses are equipped with a Clamp switch which is conve-  
nient for manual focus.  
The Clamp switch locks the manual focus position. You can use it when taking close-ups  
with a copy stand, for example.  
Using the Clamp Switch  
Focus manually, then set the Clamp switch to ON.  
The point of focus will be locked. Autofocus will also be disabled.  
• Do not turn the focusing ring forcibly while setting the Clamp switch to ON because  
there is a slight possibility that the point of focus may change.  
 
16》  
ATTACHING THE LENS HOOD  
In order to avoid the deterioration in image quality from internal reflection, use of the lens  
hood is recommended.  
The lens hood image can be diifferent  
depending on the lens hood type.  
When attaching the lens hood, align the index on the lens hood with the attaching index on  
the lens, and push both parts straight toward each other. Attach the lens hood on the lens  
by turning the hood in the clockwise direction to lock it as viewed from the front of the lens  
until it clicks into position.  
2. Memo:  
When attaching the lens hood, hold the focus ring securely to prevent them from  
turning.  
When the lens hood is not in use, it can also be turned around and attached in the  
reversed position.  
 
17》  
FILTERS  
Make sure the filter size matches the lens and then attach the filter onto the lens.  
2. Precaution on filters  
Since the filter becomes a part of the optics when attached on the lens, handle it in the  
same way you handle the lens with care to dust, dirt and scratches. Normally, attaching  
two or more filters on a lens is not recommended. However, attaching a circular  
polarizing filter and another filter would not be a problem.  
Use a circular polarizing filter with Autofocus camera for proper exposure and  
autofocusing.  
 
18》  
PRECAUTIONS WHEN USING THE LENS WITH A FLASH  
Built-in Flash  
The built-in flash can not be used when the distance is less than 0.7m. When the flash is  
used within 0.7m, that causes incorrect exposure control and vignetting in the picture  
corners.  
• The built-in flash may be blocked by the lens hood. Always make sure to remove the  
lens hood before using the built-in flash.  
 
19》  
MAIN SPECIFICATIONS  
Elements in groups  
Angle of View  
Aperture  
8 groups, 9 elements  
24.5˚  
F2.8  
Mount Type  
PENTAX KAF mount  
Minimum Focus  
0.303m  
Distance  
Max. Diameter x  
Length  
Approx. 1  
Lens Hood  
Filter Size  
SCH-B49  
49mm  
Maximum  
67.5x80.5mm  
345g  
Magnification  
Weight  
* Specifications are subject to change without prior notice.  
* All trademarks are the property of their respective owners.  
 
20》  
For customers in USA  
STATEMENT OF FCC COMPLIANCE  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions  
: (1) This device may not cause harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
Changes or modifications not approved by the party responsible for compliance could void the user's authority to  
operate the equipment.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in  
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following measures :  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
*Consult the dealer or an experienced radio/TV technician for help.  
For customers in Canada  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment  
Regulations.  
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel  
brouilleur du Canada.  
 
21》  
MEMO  
 
22》  
MEMO  
 
23》  
MEMO  
 
24》  
The CE Mark is a Directive conformity  
mark of the European Community (EC)  
Please refer to the warranty that came with your product or go  
or inquiries.  
AD68-01762A  
 

Radica Games Games I7001 User Guide
RCA Universal Remote RCRP05B User Guide
RCA VCR VR602HF User Guide
Regal Ware Refrigerator K6751 User Guide
Rival Slow Cooker SCV500GF CN User Guide
RocketFish Mouse RF MSE12 User Guide
Ryobi Trimmer 105r, 132r, 137r User Guide
Sanyo Battery Charger N 270AAK User Guide
Schwinn Home Gym 213 User Guide
SECO LARM USA Home Security System E 37EV User Guide