RocketFish Conference Phone QS2 T User Guide

Congratulations on your purchase of the RF-QS2-T  
Bluetooth Speakerphone. This speakerphone enables  
comfortable, hands-free communication with a  
Bluetooth-compatible phone.  
Voice dialing  
When no call is in progress, quickly press and release  
Power/Send/End. When you hear a tone, speak the  
number or voice tag for the number you want to call.  
(The phone must have a voice dial feature and have  
recorded voice tags.)  
Package contents  
• RF-QS2-T speakerphone • Car charger adapter  
Making a call  
• USB charging cable  
Quick Setup Guide  
To...  
Make a call  
Redial  
Answer a call  
End a call  
Refuse a call  
Change the speaker  
volume  
Do this...  
Features  
Press Power/Send/End.  
Double-press Power/Send/End.  
Press Power/Send/End.  
Press Power/Send/End.  
Double-press Power/Send/End.  
Press the volume up button (+) to increase  
volume or press the volume down (-) button to  
decrease.  
Indicator  
Volume down  
Power/Send/End  
button  
Charger  
connector  
QS2-T Car Speakerphone  
RF-QS2-T  
Volume up  
Visor clip  
Microphone  
Charging the battery  
Mute or unmute a call Press and hold the Volume down (-) button until  
a tone is heard.  
Switch a call between Press and hold Power/Send/Endfor  
the phone and the  
speakerphone  
Before using your speakerphone, you must charge it  
for about two hours. When the battery is fully charged,  
it provides up to 11 hours of talk time and up to  
1,400 hours of standby time.  
two seconds.  
1
USB charging: use the USB cable to plug your QS2-T  
speakerphone into a computer or other USB power  
port.  
Turning the indicator on or off  
Press the power and volume up buttons at the same  
time for about four seconds. The indicator turns on.  
Press the power and volume down buttons at the  
same time for about four seconds. The indicator  
turns off. You can enable or disable the indicator  
when the speakerphone is connected with your  
phone.  
2
Car charging: use the car charger adapter and USB  
charging cable to charge your QS2-T speakerphone  
in your car.  
Turning the speakerphone on  
Press and hold the Power/Send/End for about  
two seconds. RF-QS2-T beeps and the yellow-green  
indicator light starts blinking. (First time use requires  
pressing it for 4 seconds.)  
Disconnecting the speakerphone from the phone  
To disconnect the speakerphone from the phone, do  
one of the following:  
Turning the speakerphone off  
Press and hold the Power/Send/End for about  
four seconds, RF-QS2-T beeps and the red indicator light  
is displayed briefly.  
Turn off the speakerphone.  
Disconnect the RF-QS2-T in the phone’s menu.  
Move the speakerphone more than 33 ft. (10 m)  
away from the phone.  
Note: You do not need to delete the pairing to  
disconnect the speakerphone. When you reconnect a  
paired speakerphone, you will not be asked for its PIN  
again.  
If you want to pair your speakerphone with new phones,  
you don’t need to erase all paired device information.  
There can be up to eight different paired devices  
information stored.  
Pairing the speakerphone  
1
Make sure that the compatible phone is turned on  
and within 33 ft. (10 m) of the speakerphone.  
Turn on the QS2-T and make sure it’s fully charged.  
Press and hold the Power/Send/End button for  
about four seconds. The yellow-green indicator  
flashes rapidly. Release the button. The  
speakerphone is now in pairing mode.  
Activate the Bluetooth connection from the phone.  
See your phone’s documentation for more  
information.  
2
3
4
To erase paired devices from your speakerphone:  
When the speakerphone turned off, press and hold  
the Power/Send/End and volume up (+) buttons  
simultaneously for more than six seconds. A tone  
plays, and the indicator flashes red and yellow-green.  
The speakerphone then enters the pairing state  
automatically.  
Set the phone to start searching for Bluetooth  
devices.  
5
6
Select RF-QS2 from the list.  
Enter the PIN 0000 to connect (orpair”) the  
speakerphone to the phone. The speakerphone  
beeps once, and the indicator blinks yellow-green to  
 
QUICK SETUP GUIDE  
indicate the Bluetooth connection is active.  

Radio Shack Headphones ET007 User Guide
RCA CD Player CDRW120 User Guide
Rockford Fosgate Speaker R1S410 User Guide
Roland Drums TD 15 User Guide
Roland Musical Instrument PD 85 User Guide
Ryobi Battery Charger RC960 User Guide
Samsung Network Card SCH T300 User Guide
SanDisk Computer Drive pSSD P2 User Guide
Sanus Systems Indoor Furnishings TV27 User Guide
Sanyo Freezer MDF U73VC User Guide