Radio Shack Universal Remote PLCD35 User Guide

PLCD35  
INSTRUCTION MANUAL  
CAR AUDIO  
REMOTE CONTROLLER  
ANTI-THEFT FLIP DOWN DETACHABLE PANEL  
AUTO-LOADING COMPACT DISC PLAYER  
AM/FM-MPX DIGITAL PLL TUNING RADIO  
WITH INFRARED REMOTE CONTROLLER  
 
BASIC OPERATION  
For CD model with optional SUBWOOFER function  
OPEN  
BAND  
FLIP DOWN DETACHABLE CD PLAYER  
+
REMOTE  
-
SW  
MODE PWR  
SEL  
1
PAU  
2
SCN  
3
RPT  
4
SHF  
5
6
CLK  
MUTE  
DSP  
SCAN  
A.PS  
RESET  
25  
24  
CDC CONNECTOR OR AUX CABLE  
2
 
BASIC OPERATION  
1. OPEN BUTTON  
Press it to flip down the front panel then you can insert the cd disc into the cd  
compartment.  
2.3.7 SEL (AUDIO MODE SELECT)/ +/- BUTTONS  
Press SEL button to change the mode in the sequence of  
VOL  
BAS  
TRE  
BAL  
FAD  
(Volume)  
(Bass)  
(Treble)  
(Balance)  
(Fader)  
A. The volume level can be adjusted at any time by pressing the audio level+or- button  
as select mode has been initially defaulted at volume mode.  
B. The volume level is also obtained by stepping through the SEL button until  
the function VOL is displayed and then press + or - button to adjust the sound level.  
C. Press and hold the + or - button to adjust the sound level.  
D. Adjust sound balance between front and rear speakers by using + and - buttons.  
E. Press SEL button hold for more than 2 seconds and select + or- button can have a beep  
sound.  
4.6.TRACK UP /DOWN BUTTONS  
A. During CD mode, press  
button allow you to track forwards.  
Hold the  
button allow you to skip forwards.  
B. During Mp3 mode, press  
button allow you to track forwards.  
Hold the  
button allow you to skip forwards.  
For Mp3 playing (MP3 model only), these two buttons act as the digit 8 & 9 key.  
C. During RADIO mode, press and hold  
manual search channel.Then press  
or  
or  
for more than 2 seconds you can  
, you can have auto search channel.  
5. BAND BUTTON  
Press it to select your desired radio band and the band which is selected will be  
displayed on LCD. Press it hold for more than 2 seconds can have LOUD mode.  
LOUD MODE:  
When reduce the volume to half level, press it to enhance the bass effect.  
For Mp3 playing (MP3 model only), this button can act as the ENTER key.  
8-9-10-11-12-13. PRESET MEMORY BUTTONS  
A). To memorize the current frequency, press any one of the six preset Buttons hold for more  
than 2 seconds.  
B).To recall the preset memory, press one of the preset buttons [0-6].  
C).RADIO MODE  
When pressed short, these keys select a preset station directly, When pressed longer  
than one seconds, current station is stored in preset memory bank. When PTY mode is  
selected, the preset memory buttons is shared as follows:  
PTY music group - - PTY speech group - - OFF MUSIC SPEECH  
1. POP M, ROCK M  
2. EASY M, LIGHT M  
3. CLASSICS, OTHER M  
4. JAZZ, COUNTRY  
5. NATION M, OLDIES  
6. FOLK M  
1. NEWS, AFFAIRS, INFO  
2. SPORT, EDUCATE, DRAMA  
3. CULTURE, SCIENCE, VARIED  
4. WEATHER, FINANCE, CHILDREN  
5. SOCIAL, RELIGION, PHONEIN  
6. TRAVEL, LEISURE, DOCUMENT  
D).In CDP mode, press 1PAU button to pause CDP playing, press it again to resume  
CDP playing.  
E). In CDP mode, press 2SCN button to play the first 10 seconds part of each song, press  
it again to stop scanning and retain playing the song currently selected.  
F). In CDP mode, press 3RPT button to play the current track repeatedly. Press it again to  
cancel this mode.  
G).In CDP mode, press 4SHF button to play the track in random order. Press it again to  
cancel this mode.  
H).In CDC mode (optional), M5/M6 are used as UP/DOWN buttons to select DISC.  
3
 
BASIC OPERATION  
14. CLOCK BUTTON  
Press it to display time on LCD for few seconds. Press it hold and then press  
button to adjust hour or minute.  
or  
15. AF BUTTON (for RDS model only)  
AF [ALTERNATIVE FREQUENCIES]  
When pressed short, AF switching mode is selected and the state of AF switching  
mode is displayed by AF segment in display.  
Segment off: AF switching mode off.  
Segment on: AF switching mode on, and has RDS information.  
Segment flashing: AF switching mode is selected, but RDS information is not  
received yet.When AF switching mode is selected, the radio checks the signal  
strength of AF all the time. The interval of checking time of each AFs depends on  
the signal strength of current station, from a few minute for strong station to a few  
seconds for weak station. Everytime that new AF is stronger than current station, it  
switches over to that frequency for very short time, and NEW FREQUENCY is  
displayed for 1-2 second. Because the mute time of AF switching or checking time  
is very short, it is almost inaudible in case of normal program.When pressed long,  
it is activated of regional mode on /off .  
Regional mode ON  
AF switching or PI SEEK is implemented to the station which have all PI codes are  
the same as current station.REG of individual segment is turned on also together  
with displaying REG ON numeric display for a few seconds.  
Regional mode OFF  
The regional code in the format of PI code is ignored when AF switching or PI SEEK  
is implemented. REG of individual seg. is turned off together with displaying REG  
OFF on numeric display for a few seconds.  
16. TA BUTTON (for RDS model only)  
TA function [TRAFFIC ANNOUNCEMENT] BUTTON  
When pressed short, it is activated as TA mode on or off.  
When TA mode is on and traffic announcement is transmitted:  
1). When the unit is in CD mode, it will switch to radio mode temporarily.  
2). Temporary switch over to an EON linked station when EON detects a traffic  
announcement on that other program.  
3). If the volume level was under the threshold point, it will be raised to the threshold  
point.  
But the user changed the volume level which was more than the threshold point  
(min. TA volume level), it will be set to the last level.  
When pressed long , it is selected EONTA LOCAL / EONTA DISTANCE mode.  
The purpose of this key is to reduce unwanted EON TA switching, which EON TA  
information was received from current station and the radio switched to that EON  
linked station, but no information could not be received because the EON linked  
station is located too far from that area.  
So the radio is switched back to current station again.  
In above operation, a customer listen to a wrong program or mute sound for a while.  
EONTA LOCAL mode  
When the filed strength level of EON linked is less than the threshold level, the radio  
does not switch that station, and a customer can hardly listen to any disturbances.  
When EONTA LOACL mode is selected, EONTA LO on numeric display is indicated  
for a few seconds.  
EONTA DISTANCE mode  
EON TA switching is try to implemented by the information of current station .  
When EONTA DISTANCE mode is selected, EONTA DX on numeric display is  
indicated for a few seconds.  
4
 
BASIC OPERATION  
17. PTY(PROGRAM TYPE) BUTTON  
This key is operated as follows:  
PTY MUSIC group- - PTY SPEECH group- - PTY OFF  
While selecting PTY TYPE, its selection is implemented by preset buttons as  
described in preset key. When PTY is selected, the radio starts to search  
corresponding PTY information, and stops if the corresponding PTY information is  
detected.  
If corresponding PTY information is not existed any more, PTY type is automatically  
exit to normal mode.  
18. APS/MP3 BUTTON  
In radio mode:  
When short pressing, the radio searches for each preset station.  
When the field strength level is more than the threshold level of stop level, the radio is  
holding at that preset number for few secretary with releasing mute, and than  
searches again. In FMband, FM 1, FM 2 and FM 3 is checked one at a time. When  
long pressing (more than 1 second),the radio searches from the current frequency  
and checks the signal strength level until 1 cycle search is finished. And then 6  
strongest stations are preset to the corresponding preset number.  
The AS operation is implemented in the each band of selected band. When the AS  
operation is finished, the radio executes the preset scan.  
In MP3 mode, press 0-9 and ENTER button to play the track in 1-108 number.  
19. MODE BUTTON  
Press it repeatedly to select CDP, AUX and RADIO mode in sequence and  
circulation.  
For SUB WOOFER function(optional), press and hold for more than 2 seconds can have  
WOOFER Mode.  
For Mp3 playing (MP3 model only), this button can act as the digit 7 key.  
20. POWER BUTTON  
Press it to turn on or off the unit.  
21. MUTE BUTTON  
Press it to eliminate the sound immediately.  
22. DSP BUTTON  
Press it to switch between 4 preset equalizer curves: FLAT, CLAS, POP M, ROCK  
M. The sound quality will be changed.  
23. SCAN BUTTON  
Press it to scan up by one channel step with station detection.If a valid signal has  
detected, the current frequency is blinked within 5 seconds,then press it again to  
stop scan and remain the current frequency; otherwise, the unit continue to scan  
up by one channel step with station detection 5 seconds later.  
24. FLASHING LED  
If the front panel is not on the main unit, LED will be flashing.  
25. RESET  
RESET button is placed on the housing and must be activated with either a ballpoint  
pen or thin metal object.The RESET button is to be activated for the following  
reasons:  
- Initial installation of the unit when all wiring is completed.  
- All the function buttons do not operate.  
- Error symbol on the display.  
Note:If press RESET button, the unit can’t work yet, please use a cotton swab  
soaked in isopropyl alcohol to clean the socket on the back of the front panel.  
5
 
ELECTRIC CONNECTION  
FOR 4X7W or4X30W  
AUX cable (optional)  
RCA RED  
ANTENNA CONNECTOR  
LCH WHITE  
OR  
CDC connector (optional)  
IGNITION  
SWITCH (B+)  
RED  
FUSEBOX  
YELLOW  
MEMORY (B+)  
FRONT RCA OUTPUT  
RCH RED  
CABLE (optional)  
BLACK  
BLUE  
GROUND (B-)  
AUTO  
ANTENNA  
LCH WHITE  
WHITE  
GREY  
GREY/BLACK  
VIOLET  
FRONT  
LchSPK  
FRONT  
RchSPK  
WHITE/BLACK  
GREEN  
REAR  
REAR  
LchSPK  
RchSPK  
GREEN/BLACK  
VIOLET/BLACK  
FOR SUBWOOFER (4X7W or 4X30W)  
AUX cable (optional)  
RCA RED  
ANTENNA CONNECTOR  
LCH WHITE  
OR  
CDC connector (optional)  
SUB WOOFER  
RCA  
IGNITION  
SWITCH (B+)  
RED  
GREEN  
FUSEBOX  
YELLOW  
MEMORY (B+)  
FRONT RCA OUTPUT  
CABLE (optional)  
RCH RED  
BLACK  
BLUE  
GROUND (B-)  
AUTO  
ANTENNA  
LCH WHITE  
WHITE  
GREY  
GREY/BLACK  
VIOLET  
FRONT  
FRONT  
RchSPK  
LchSPK  
WHITE/BLACK  
GREEN  
REAR  
REAR  
LchSPK  
RchSPK  
GREEN/BLACK  
VIOLET/BLACK  
NOTE:  
In spite of having any kinds of speaker system,must use 4 ohms impedance of speaker  
to reduce the distortion during high volume level.  
6
 
INSTALLATION  
DASH BOARD  
METAL MOUNTING STRAP  
HEX NUT  
SPRING WASHER  
CONSOLE  
PLAIN WASHER  
SLIDE BRACKET HOUSING  
HEX BOLT  
TAPPING SCREW  
KEY PLATE  
PLASTIC TRIM OUT  
KEY PLATE  
While installing the front panel,  
please mount the left side first,  
then push the right side.  
TAPPING SCREW (M1.7X4 KM BLACK)  
7
 
INSTALLATION  
CAUTION: Do not install the detachable panel before connecting the wire.  
1. The unit is designed for negative terminal of the battery which is connected to the  
vehicle metal. Please confirm it before installation.  
2. If the car interior is extremely hot, as after being parked in the sun, do not use the  
player until the car has been driven for a while to cool off the interior.  
3. Press the OPEN button to flip down the front panel (see fig.1), then take away the  
front panel (see fig.2) and put it in the protective case (see fig.3) safe keeping.  
4. Install the front panel back into its bracket and then push it back to the position for  
playing (see fig.4).  
FRONT PANEL  
FRONT PANEL  
OPEN BUTTON  
( FIG.1)  
( FIG.2)  
PROTECTIVE CASE  
FRONT PANEL  
FRONT PANEL  
( FIG.3)  
( FIG.4)  
8
 
DISC NOTES  
DISC PLAY:  
Cleaning discs  
Before playing, clean the disc with a clean, lint-free.  
Flip the disc in the direction of the arrow.  
NOTE:  
Do not use so solvents such as benzine, thinners. Commercially available  
cleaners or anti static spray damage the unit.  
Insert a disc with the label surface down. Doing so may damage the unit.  
NOTE:  
Do not try to insert another disc when one has been already inserted.  
Doing so may damage the unit.  
Handle the disc by its edge. And to keep the disc clean, do not touch the surface.  
Do not stick paper or tape on the disc.  
Do not expose the disc to direct sunlight or heat sources such as hot air ducts. Or leave  
it in a car parked in direct sunlight where there can be a considerable rise in  
temperature.  
Label  
surface up  
Preparing the Remote Control  
Inserting the Batteries  
1. Open the battery compartment cover.  
2. Insert the new batteries.Make sure that the positive and negative terminals of  
thebatteries are oriented indicated.  
3. Close the cover  
Using the Remote Control  
Face the remote control towards the player front face IR mark (remote control signal  
receiver).  
Operation angle: About 30 degree in each the direction of the front of the IR mark.  
9
 
SPECIFICATIONS  
GENERAL  
Power requirement.............................................................................................DC 12V  
Current consumption .....................................................................................5A or 15A  
POWER OUTPUT ................................................................................4x7W or 4x30W  
FM SECTION  
For 3 Bands  
(Europe)  
For 2 Bands  
(Europe)  
For 2 Bands  
(U.S.A.)  
Frequency range  
87.5 to 108 MHz  
87.5 to 108 MHz  
87.5 to 107.9 Mhz  
Usablesensitivity ......................................................................................................3uV  
I.F Frequency .................................................................................................10.7MHz.  
AM SECTION  
For 3 Bands  
(Europe)  
For 2 Bands  
(Europe)  
For 2 Bands  
(U.S.A.)  
Frequency range  
522 to 1620 KHz  
522 to 1620 KHz  
530 to 1710 Khz  
LW SECTION  
For 3 Bands  
(Europe)  
For 2 Bands  
(Europe)  
For 2 Bands  
(U.S.A.)  
Frequency range  
144 to 288 KHz  
LINE - OUT [OPTION]  
Output ........................................................................500mV @ FM 10% THDPOWER  
CD PLAYER  
System ..............................................................................compact disc audio system  
Usable disc ..............................................................................................compact disc  
Signal format ..................................................................sampling frequency 44.1KHz  
No of quantization bits ............................................................................................1bit  
Frequency characteristics.............................................5-40Hz-5dB 10K-20KHz - 5dB  
Signal to noise radio ....................................................... 70dB [1KHz][IEC-A net work]  
Number of channels .....................................................................................2 STEREO  
Chassis dimensions................................................................184 [W] X 54[H] X 170[D]  
10  
 
TROUBLE SHOOTING  
Before going through the check list, check wiring connection. Should any of the  
problems persist after check list has been made, consult your nearest service dealer.  
Symptom  
No power.  
Cause  
Solution  
The car ignition switch is  
not on.  
If the power supply is properly  
connected to the car accessory  
terminal, switch the ignition key  
to ACC.  
The fuse is blown.  
Replace the fuse.  
Disc cannot be  
loaded or ejected. the player.  
Presence of disc inside  
Remove the disc in the player,  
then put a new one.  
Inserting the disc in reverse Insert the compact disc with  
direction.  
the label facing upward.  
The disc is extremely  
dirty or defective.  
Clean the disc or try to play a  
new one.  
Temperature inside the car Cool off or until the ambient  
is too high.  
temperature return to normal.  
Condensation.  
Leave the player off for an hour,  
then try again.  
No sound.  
Volume is in minimum.  
Adjust volume to a desired level.  
Check wiring connection.  
Wiring is not properly  
connected.  
Sound skips.  
The installation angle is  
more than 30 degrees.  
Adjust the installation angle less  
than 30 degrees.  
The disc is extremely dirty  
or defective disc.  
Clean the compact disc, then  
try to play a new one.  
The operation keys The built-in microcomputer Press the RESET button.  
do not work.  
is not operating properly  
due to noise.  
Front panel is not properly fixed  
into its place.  
The radio does not The antenna cable is not  
Insert the antenna cable firmly.  
work.  
connected.  
The signals are too weak.  
Select a station manually.  
88-C2330-01  
11  
 

Ricoh Projector PJ WX3131 User Guide
Roberts Radio Radio RD 6R User Guide
Russell Hobbs Hot Beverage Maker T22 5000583 User Guide
Ryobi Trimmer P2001 User Guide
Samsung Air Conditioner AS070VE User Guide
Samsung Air Conditioner SC18ZV User Guide
Samsung CRT Television TX T2781, TX T2782, TX T2082 User Guide
Samsung Home Theater System HT DS660 User Guide
Samsung MP3 Player YP R0 User Guide
Sanyo Car Stereo System FXCD 1100 User Guide