Q See Security Camera QSTC201 211 User Guide

Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE  
1. Connection Diagram  
a. Connect the Q-See IP camera to the same Router as your PC.  
2. Setting up the Connection on a PC  
a. Find the IP address of the PC: To do this:  
Go to Start – Run (XP) and type CMD. In Vista, type CMD in Search. You will get the Command prompt  
screen. Type in “IPCONFIG”. Note the IP Address, Subnet Mask Address and Default Gateway Address  
listed on your command screen and write these down for future reference. See example below (Figure  
1).  
(Figure 1)  
*Note the IP Address for this example is 192.168.0.105,  
the Subnet Mask is 255.255.255.0 and the Default Gateway is 192.168.0.1  
b. Insert the installation CD for the Q-See IP camera and Install the Q-See IP Camera as prompted by the  
pop-up menu that appears on your screen.  
c. Once the Q-See IP Camera Software is installed:  
Go to: Start-All Programs-ControlCenter-IPTOOL. You will see a dialog box listing all connected IP  
Cameras with the appropriate Addresses listed. See example below (Figure 2).  
(Figure 2)  
*Note that the example of this IPTOOL screen above lists an IP Camera with the Device Name of “name”,  
an IP Address of 192.168.1.201, a Subnet Mask of 255.255.255.0 and a Gateway of 192.168.1.1  
 
(Figure 6)  
3. Setting up the Wireless Function of the Camera  
a. In your Internet Explorer Browser window (See Figure 7), click on the “System Config” button on the  
bottom right hand side of your screen.  
b. A Menu Box will appear (See Figure 7). In this Menu Box, choose the “Wireless config” option nested  
under “Network config” on the left hand side (circled in red in Figure 7).  
c. Check the “Wireless Switch” box located at the top of your Menu Box.  
d. Click the “Refresh” button in your Menu Box (as indicated in Figure 7) and your system will now detect  
the wireless router connected to your computer. The name of your router will appear in your list of  
routers under the column “SSID”. Clicking on the router will reveal the IP, Gateway, DNS and Subnet  
Mask Addresses on lower right hand side of your Menu Box.  
(Figure 7)  
 
i. If your Router is encrypted, then you will need to set all the addresses manually with the  
addresses listed on your IPTOOL screen (See Figure 4). To do this, check the “Use the Following  
IP Address” box on your Menu Box (Figure 7) and enter the information manually.  
e. Once you have completed the set up, click the “Save” button at the bottom of the screen on your Menu  
Box.  
f. Once you have saved your settings, you can now disconnect the Cat-5 cable from the camera and place  
the camera anywhere within the range allowed by your wireless router. Please note that each router  
will afford you different ranges of connectivity and you should refer to your Router’s manual for more  
accurate and detailed information.  
g. Run the IPTOOL program again to ensure that your new Q-See IP Camera is detected by your Router. If  
not, station your camera closer to your Router.  
Questions or Comments?  
Contact Us:  
Mailing Address:  
DPS Inc.  
Customer Service:  
Phone: 877-998-3440 x 538  
Live Chat from our Website  
8015 E. Crystal Dr.  
Anaheim, CA 92807  
Website:  
Tech Support:  
Fax:  
Phone: 877-998-3440 x 539  
Live Chat from our Website  
714-998-3509  
*We recommend that you place this camera in a room that has enough air circulation to avoid overheating  
*To see this camera over the Internet you need to forward port 80 and 9008 in the Router. For more details about Port  
Forwarding, please refer to the User Manual.  
 

Q See Home Security System Q25DVR4ES User Guide
Radica Games Video Game Console 8046 User Guide
Radio Shack Radio HTX 242 User Guide
RCA MP3 Player TC1200 User Guide
Remington Hair Dryer DS 1000 User Guide
Roland Drums TD 8KV User Guide
Roland Musical Instrument ARX 01 User Guide
Rolls Portable Multimedia Player HM57 User Guide
Samsung Camcorder DC171BI User Guide
Schumacher Power Supply 00 99 000674 User Guide