Q See Lawn Mower QT17D324SC User Guide

QT17D324SC  
User’s Manual  
Contact Us:  
Q-See Products  
8015 E. Crystal Dr  
Anaheim, CA 92807  
Website:  
Customer Service:  
Phone: 877-998-3440 x 538  
Tech Support:  
Phone: 877-998-3440 x 539  
Fax:  
714-998-3509  
Rev 061609  
 
QT19D328SC User’s Manual  
IMPORTANT SAFEGUARDS  
CAUT ION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION:TO REDUCE THE RISK OF ELECTRIC  
SHOCK,DO NOT REMOVE THE BACK.  
NO USER SERVICEABLE PARTS  
INSIDE. REFER SERVICING TO  
QUALIFIED SERVICE PERSONNEL  
Graphic Symbol Explanation  
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the  
presence of un-insulated dangerous voltage within the Product’s enclosure that may be of sufficient magnitude to  
constitute a risk of electric shock to people.  
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important  
operating and maintenance (servicing) instructions in the literature accompanying the appliance  
Warning - To Prevent Fire Or Shock Hazard, Do Not Expose This Monitor To Rain Or Moisture.  
This Product Must Be Grounded.  
Product Specifications Are Subject To Change Without Notice.  
CAUTION: This equipment is to be opened by ONLY by a qualified service person. There are no user serviceable parts  
inside. Opening this equipment may expose you to dangerous voltage and other risks. Incorrect re-assembly of this  
equipment may result in electric shock.  
1Read lnstructions: All the safety and operating instructions should be read before the appliance is operated.  
2Follow lnstructions: All operating and use instructions should be followed.  
3Cleaning: Unplug this monitor from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or  
aerosol cleaners.  
4Water and Moisture: Do not use this monitor near water, for example, near a bathtub, wash bowl, kitchen sink, laundry tub, in  
a wet basement, swimming pool, or any other wet surface.  
5Accessories: Do not place this monitor on an uneven surface. The monitor may fall, causing serious injury and serious damage  
to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the supplier, or sold with the monitor.  
6Ventilation: Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the monitor, and to  
protect it from overheating. These openings should never be blocked by placing the monitor on a bed, sofa, rug, or other  
similar surfaces. This monitor should never be placed near or over a radiator or heat register. This monitor should not be  
placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or supplier instructions have  
been adhered to.  
7Object and Liquid Entry: Never push objects of any kind into this monitor through the openings as they may touch  
dangerous voltage points or short-out parts that would result in a fire or electric shock. Never spill liquid of any kind on the  
monitor.  
8Repair (Servicing): Do not attempt to repair this monitor yourself as opening or removing the cover may expose you to  
dangerous voltage or other hazards. Refer to qualified service personnel.  
9Replacement Parts: Please contact Q-See for replacement parts.  
3
 
QT19D328SC User’s Manual  
10Safety Check: Upon completion of any service or repair to this monitor, ask the service technician to perform safety checks  
to determine that the monitor is in proper operating condition.  
11Retain Instructions: The safety and operating instructions should be retained for future reference.  
Chapter 1 Product Information  
1.1 Product Description  
This product is a four channel digital monitoring product that is specially designed for the security industry. It has  
an embedded processor and operating system, and also uses the most advanced technologies in the IT field, such  
as MPEG-4 video and audio compressing & decompressing, recording to large volume hard drive, TCP/IP network  
and other technologies. The firmware encoded in FLASH memory has changed the traditional mode of Monitor with  
DVR. It integrates the Monitor with the DVR insteadwhich not only is more convenient for users to operate but also  
makes the system more stable and easier to maintain.  
1.2 Product Features  
This product uses a high-speed embedded processor and a real time operating system, it offers high stability,  
high durability, is crash free and also easy to maintain.  
Easy to install and use.  
Two levels of password protection, administrator and user guarantee the security of the system.  
The system uses an OSD (On Screen Display) graphical interface, which is more  
convenient for  
operators to use.  
The system uses pure hardware MPEG-4 Changeable stream or fixed stream video compressionand  
supports HD1 and CIF resolution recording on each channel, the frame rate for recording is adjustable, from  
high sharpness to super-low hard drive space usage.  
Uses FAT32 format for storage, and can use one IDE hard drive up to 300GB.  
Four channels video input, two channels video outputone channel VGA outputTwo channels audio input,  
two channels audio output, and one USB Port.  
Three channel alarm input, one channel linkage alarm output and one channel trouble alarm output.  
Real time monitoring and playback in single picture mode, dual channel mode or quad mode .  
The system supports turning the machine on and off automatically. In case of power outage, it resumes  
recording automatically once the power is restored. Alarm will go off automatically when no video signal is  
being received. This eliminates the need to frequently monitor the system.  
Manual recording, scheduled time recording, alarm recording, and motion detection recording. Alarm and  
motion detection recording saves hard drive space allowing you to record for longer periods of time.  
Using the motion detection recording function, you can setup the areas of the camera view that you want to  
be sensitive to motion.  
The system supports pre-alarm recording and post alarm recording periods.  
Equipped with 2x, 4x times fast forward/ fast reverse play functions and 1/2x, 1/4x, 1/8x speed slow motion  
reverse play, pause, frame by frame play and other playback control functions.  
The system supports PAL and NTSC systems, so the system can be used universally.  
Brightness, contrast, Color and Tint can be setup independently for each channel.  
Alarm log and operating log facilitates convenient analysis and searching.  
RJ-45 universal network telecom interfacenetwork transmitting ways include ADSL, ISDN, LAN and CAN.  
The included client software allows long-distance monitoring and playback over the internet, and supports  
TCP/IP, UDP/IP and many other net transport protocols.  
4
 
QT19D328SC User’s Manual  
RS-485 interface on the system can be used to control P.T.Z cameras with various communication protocols.  
VGA output supports 720×480, 1280×720 and 1920×1080 Resolution modesbetter quality picture can be  
attained by using progressive scanning.  
Supports file backup to IDE hard drive.  
Equipped with USB2.0 port which can be used for backup to your PC or laptop directly from the DVR hard  
drive.  
Chapter 2 System Installation  
2.1 Installing the Hard Drive  
Note: please set the hard drive to “Master” mode when connecting to the DVR.  
2.2 Rear Panel Layout  
VIDE  
O1  
1
3
2
4
VIDEO OUT  
1
2
USB  
NET  
AUDIO IN  
R
L
L
AUDIO OUT  
R
VGA  
ALARM  
VIDEO IN14 Video Input  
VIDEO OUT12 Video Output  
USBOne Channel USB terminal input  
NETOne Channel NETWORK terminal Input  
5
 
QT19D328SC User’s Manual  
AUDIO INOne Channel left/ One Channel right audio input  
AUDIO OUTOne Channel left/ one Channel right audio output  
VGAOne Channel VGA terminal input  
6
 
QT19D328SC User’s Manual  
Chapter 3 System Operation  
3.1 Layout of Front Panel and Remote Control  
3.1.1 Front Panel  
POWE R  
H.D.  
ALARM  
NET  
IR  
Buttons on front panel and their functions:  
Indicating light area  
NETindicating light for network activity  
ALARMindicating light for alarm activity  
The alarm light will be on once the alarm is startedno matter what kind of alarm it is for)  
H.D. Indicating light for Hard Drive activity  
The light turns on when Hard Drive reads and writes data.  
POWER Indicating light for power  
The light turns red when the power is on;  
Buttons area  
Menu operating buttons  
UP Directional button;  
Down Directional button;  
Left Directional button;  
7
 
QT19D328SC User’s Manual  
Right Directional button  
buttonfor confirmationchoose the menu items, and press this button to enter into the selected  
sub-menuPressing this button can display the real time of the system when playing back  
recordings.  
Functional Buttons Area  
ButtonMain Menu, used for setting each function of the system.  
ButtonPlay the existing recordings on the hard drive.  
ButtonSearch buttonused for checking recorded information on the hard drive.  
ButtonExit buttonexit from the current operating menu to last selected menu.  
ButtonRecording button, manual recording on all four channels can be started at the same time when the  
screen is in quad mode, dual views manual recording can be started when the screen is under two  
channel surveillance modeSingle channel Manual recording can be started when the monitor is  
under single channel surveillance mode.  
ButtonFor stopping the recording button and the manual recording.  
ButtonFast Rewind button, at speed of X2 and X4 times.  
Buttonfast forward buttonPlay the recorded picture fast forward at speed of X2 and X4 times.  
ButtonPress this button continuously to see the picture frame by frame.  
ButtonUsed for switching between quad, dual and single picture modein the following order:  
Channel 1Channel 2Channel 3Channel 4Dual Views (Channel 1- Channel 2) Dual Views (Channel 3-  
Channel 4) quadChannel1  
8
 
QT19D328SC User’s Manual  
3.1.2 Remote Control  
9
 
QT19D328SC User’s Manual  
L OGI N/ L OCK  
P O WE R ON  
PLAYBACK  
3
6
9
2
5
1
4
7
QUAD  
PARAMETER  
ANALOG  
8
0
+
Z OOM+  
Z OOM-  
FOCUS-  
FOCUS+  
EXI T  
AUTO  
PLAY  
F WD  
RECALL  
S WI T C H  
PRESET  
SL OW  
REV  
CF  
NET  
SET UP  
RECORD ST OP  
F2  
F3  
F4  
F1  
Buttons on Remote Control and Their Functions:  
10  
 
QT19D328SC User’s Manual  
Digital ButtonArea  
0-9ButtonDigital buttonsused for digital input or video switchwhen in quad mode, press 1,2, 3, 4 digit  
buttons to switch the picture output between the first, second, third and forth video channels.  
+-ButtonAdjusting various parameters;  
Menu Operating Buttons Area  
UP Directional button;  
DOWN Directional button;  
LEFT Directional button;  
RIGHT Directional button;  
ENTERbuttonfor confirmationchoose the menu items, and press this button to enter into the selected  
sub-menuPressing this button can display the real time of the system when playing back the  
recordings;  
PTZ control function buttons  
ZOOM+,ZOOM-ButtonAdjust the distance of the picture;  
APERTURE+,APERTURE-ButtonAdjust the brightness of the picture;  
FOCUS+,FOCUS-ButtonAdjust the sharpness of the picture;  
AUTOButtonControl automatically;  
RECALLButtonStandby button in control of PTZ;  
PRESETButtonPreset control on PTZ, standby button;  
SWITCHButtonControl on some assistant switch;  
Play function buttons  
PLAYButtonPlay the recordings on the hard drive;  
SLOWButtonPlay the images slowlyat speed of 1/2x, 1/4x, 1/8x timesor pressplaybutton to return  
to normal playing speed;  
PAUSE/SETPButtonPress one time to Pause the videowhen pressing continuouslypicture will be  
11  
 
QT19D328SC User’s Manual  
displayed frame by framepressPlaybutton to return to normal speed;  
FWDButtonPlay fast forward through the playback videoat the speed of 2x, 4x timespressPlay】  
Button to return to normal speed;  
REVButtonPlay fast backward through the playback videoat speed of 2x, 4x timespressPlayButton  
to return to normal speed;  
Other function buttons  
POWER/ONButtonfor turning the machine on and offStandby and start;  
LOG IN/LOCKButtonget the operating rightsto type in the password and lock operation;  
PLAYBACKButtonfor reviewing the recordings, log, state of hard drive, information of software edition  
and so on;  
QUADButtonFor switching display between quad, dual views and single pictureOrder of Display:  
Channel1→Channel 2→Channel 3→Channel 4→Dual views (Channel 1-Channel 2)→Dual  
views (Channel3-Channel 4) →Built-in quad→ Channel 1  
ANALOGButtondisplay the brightness, contrast, color and tint, adjusting its parameters using the+,  
-buttonsThis operation can only be performed when you are in single picture mode  
and the channel can not be recording at the time;  
EXITButtonExit buttonExit from the operating menu, return to the last selected menu.  
CFButtonEnter into the standby menu for recording material, copy the files on the hard drive to the  
backup port.  
LANGUAGEButtonEnter into “language selection” menu to setup the language.  
NETButtonStandby button;  
RECORDButtonStart manual recording in single, dual or quad mode.  
STOPButtonStop manual recording in single, dual or quad mode.  
SETUPButtonWhen logged into the system, press this function button to enter into the menu setting of  
12  
 
QT19D328SC User’s Manual  
the system;  
F1ButtonFor pick time play on the recorded pictures;  
F2ButtonPress this button to enter into the control menu for PTZ cameras when under the single  
channel mode.  
Press left, right, up and down buttons to change the position of the PTZ camera;  
PressZoom+,Zoom-ButtonAdjust the distance of the picture;  
PressAperture+,Aperture-ButtonAdjust the brightness of the picture;  
PressFocus+,Focus-ButtonAdjust the sharpness of the picture;  
PressAssistantButtonControl on some assistant switch;  
PressAutoButtonControl automatically;  
PressEventButtonstandby button in control of PTZ;  
PressPresetButtonPreset control on PTZ, standby button;  
Press the F2button again or Exitbutton to exit the setting for the PTZ control menu;  
F3ButtonStandby Button.  
F4ButtonSwitch between the monitor and VGA output;  
Operating functionPress F4button in remote control unit to switch between output of monitor  
and output of display while monitoring cameras. Its order is: output of monitor VGA 1VGA  
2VGA 3There are three modes for VGA output, to adjust to different VGA resolutions.  
3.2 Accessing the System  
3.2.1 System Start  
After supplying power to DVR, the system enters into stand-by statethe power indicating light is on solid red).  
After pressing the on/offbutton on the remote control unitthe system startsvideo is displayed on the  
screen in quad modethe number showing in each frame is its video input channel No.the time will be displayed on  
the top center of the screen.  
13  
 
QT19D328SC User’s Manual  
Note: If time recording has been setup on this machineand power is connected during this period, then  
the machine will start and enter into quad mode directly without needing to presson/offbutton again to start  
the machine.  
If the channel numbers and time are not being displayed, please pressENTERbutton on the remote control  
unit or panel, and the channel numbers and time will be displayed on the screen.  
NOTE: If the hard drive has not been installed before turning on the systemor the hard drive is not  
detected by the system after turning it onthe monitor with hard drive will set off the alarmPlease log into  
the system to turn off the alarm.  
3.2.2 System Login  
Note: Pre-delivery code for this system is000the default password for administrator is 88888888and it is  
00000000 for user. Administrator has all operating rights. In order to insure secure running of the system,  
administrators should change its code and default password of the machine as soon as possible.  
When the host machine is starteduser can only operate the system when logged in (if the  
password is effective). If there is no activity within 100 seconds after logging in, the system will enter into lock  
up state!  
When the machine is just started or under lock up state, press the Login/LockButton on Remote Control  
Unitthe login interface will appear on the screen, type in the code of the systemPre-delivery setup“000”and then  
type in the passwordpassword for administrator or user of this machine.  
If correct user’s password is typed inthe monitor will show “Password Correct” message on the screenand  
then after [Return] for confirmationusers can operate each of the items within the permitted fields (the default  
password for user is00000000).  
If correct administrator’s password is typed inthe monitor will show “Password Correct” message on the  
screenand then after [Return] for confirmationadministrator can do all of the operations on the systemThe  
default password for administrator is88888888).  
3.2.3 System On and Off  
When the system is monitoring video, please press the on/offbutton in the remote control unit twice if you  
14  
 
QT19D328SC User’s Manual  
want to turn off the systemthe system will change into standby mode from running mode when it is offIf you want  
to restart the system, please press the on/offbutton on the remote control.  
3.3 Using the System  
When the system is running, press setupbutton to enter into the OSD main menu. Use the “  
,
,
,
” directional buttons on the remote control unit to go to the desired menuPressENTERto enter into each  
menu, the menu options will be explained one by one in the next section.  
3.3.1 System Set  
Move the cursor to the position of System setup, (the color of the characters turns blue with white bottom),  
PressENTERbutton to enter into its settings or sub menuafter entering into the sub-menuhighlight the items  
with cursor keys to change the settings.  
System Setup  
Time2006.03.30. 09:23:08 Friday  
Machine No001  
Machine Address:  
HDD overwriteYes  
SystemPAL  
NTSC  
Password EnableYes  
No  
Admin Pwd Modify Operate Pwd Modify  
H.D format  
Default Setup  
Return  
Move the direction key to each sub-menu and press enter for setting.  
a). Time: When you have adjusted the year, month and day, the time will appear automatically. Move the cursor where you want  
to make the changes and press enter for adjusting or type in the numbers using the remote control.  
15  
 
QT19D328SC User’s Manual  
b). Machine’s device number: Use can use numbers from “000” to “999”. Machine’s device number has been preset to “000” at  
the factory. You need to input this number when the system is running.  
c). Machine’s address: Manually enter the machine’s address here (optional). Machine address could be the address of the place  
being monitored thru this system. Move the cursor to the “address” line and press enter to enter the address and press enter  
again when finished. Use the remote control to enter the numbers and letters. The number keys can be used for letters similar  
to the keys on a standard telephone. For example “2” represents 2abc etc.  
Note: The length limit is 8 characters or 4 words.  
d). HDD overwrite: You have two options – “Yes” & “No”. When “Yes” is selected, it will allow recording continuously even  
after the hard drive is full and video will be recorded in FIFO (First-in-first-Out) format; When “No” is selected, it will stop the  
recording function once the hard drive is full.  
e). Video System: The video system can be changed from NTSC to PAL and vice versa using the left and right arrow keys on the  
remote.  
f). Modify the administrator Password: Press enter to access the option to reset the administrator password. You can press the  
number keys on the remote control to enter the new password .  
Please note that only the administrator has the authority to do change this password.  
g). Operator Password: Press enter to access the option to reset the operator password. You can press the number keys on the  
remote control to change the password. Press the Enter key to save this setting.  
Note: Please memorize your password and save it in a secure place to avoid others from accessing it.  
h). HDD format: Use this function to format the hard drive.  
Warning: All the data on the hard drive will be lost.  
i). Default Setup: This function will reset the system to factory settings  
j). Return: This function takes you back to the Main Menu.  
3.3.2 Channel Set  
The channel setting includes channel name, screen display, clock insert, TV screen cover, etc.  
Channel Setup  
CH  
1
2
3
4
Title  
Whse  
CH name Time InSert  
Mask  
Off  
On  
Off  
Off  
CH View  
Allow  
Allow  
Allow  
Blind  
On  
Off  
Off  
Off  
Off  
Top  
Bottom  
Off  
a). Channel: Indicates the channel number. If it has a “X” symbol in front of the channel number it indicates an invalid channel.  
Note: For each channel it means the channel can not record video. However you can still see the camera image under monitoring  
status if the channel has an image signal but, the system will not prompt the alarm message if the image signal of this TV screen  
has lost.  
b). Title: Name of the channel. Enter the title of the camera location. Move the cursor to this topic and press enter and enter the  
channel title. Use the remote control to enter the numbers and letters. The number keys can be used for letters similar to the keys  
on a standard telephone. For example “2” represents 2abc etc. When you have finished press enter.  
c). Screen display: Two choices are switch on or switch off. If you choose switch on, it will show the channel title while  
monitoring. If you choose off, it will not show a channel title while monitoring.  
d). Time Insert: There are three choices for users Off, Bottom, or Top. If you choose Top, the system will insert the time at the  
top of the TV screen. If you choose bottom, the system will insert the time at the bottom of the TV screen. If you choose off, the  
system will not display the time on the screen.  
e). Mask: Two choices for users are switch on or switch off. You can press enter to change the setting. TV mask is used to  
hide an area of the camera view that you do not want to appear on the TV screen. When you select Yes the screen will appear with  
a white square. You can use the direction keys on the remote and the enter button to select the area you want to mask, and then  
use the exit button on the remote to return to the previous screen.  
f). Channel View: Two choices for users are allow or blind. You can press enter to change the setting. Choose Allow to display  
the video from the camera on the TV and Blind if you do not want the video from the camera to appear on the TV. If you select  
16  
 
QT19D328SC User’s Manual  
Blink the video from the camera will still be recorded.  
3.3.3 Alarm Set  
Alarm/Timing Setup  
Port Alarm Mode Timing Setup  
1
2
3
4
On  
On  
Off  
Off  
Close Record Delay: 030  
Open Output Delay: 010  
Close Buzzer Duration: 000  
Close I/O Alarm Out: On  
Motion Alarm Out: On  
a). Terminal Port: 1,2, 3, 4 represent the 4 outer I/O alarm input ports.  
b). AlarmTwo choices are On or Off. Users have the option to turn on /off alarm for each channel  
c). Input Mode: Two choices are Close/Open, closed circuit and open circuit. Users have the option to Normally Closed or  
Normally Open alarms.  
d). Record Delay: Record delay is the length of time the DVR keeps the file open once the alarm has stopped before starting a  
new file with the next detected alarm event. The options are from 10 to 300 sec.  
e). Output Delay: Under the alarm recording mode, the system is communicating the alarm output signal with the alarm output  
end point automatically after moving the testing signal has received the alarm signal from the I/O. Delay the alarm output  
means delaying the continuous time of the alarm’s output signal.  
f). I/O alarm output: Two choices are On or Off. This option opens or closes the option to send a signal from the DVR to  
another alarm device.  
g).Motion alarm output the same as the above except for built-in motion detection instead of an external alarm sensor.  
3.3.4 Work Set  
Record Setup  
Channel  
Schedule  
Setup  
Setup  
Setup  
Setup  
Area Set  
Setup  
Setup  
Setup  
Setup  
1
2
3
4
Return  
The Work Set Menu includes scheduling recording for each channel and the option to set up the senitive area for each channel for  
motion detection.  
The specific operation of each function is given below:  
17  
 
QT19D328SC User’s Manual  
I. Setting the recording time: Press Setup for each channel under “Schedule” to setup the day (Mon-Sun), Time of First Segment,  
recording mode (Time, Alarm or motion) Time of Second Segment, and type of recording mode. There are 2 segments of  
recording to accommodate recording overnite. For example, if you start recording at 11:30pm on Monday and stop at 11:00am  
on Tuesday, the first set will be 11:30pm to 11:59pm and the second set will be 12:00am to 11:00am.  
II. Setting Recording Area:  
The sensitivity area of the screen is made up of 192 small areas. The light green represents the area that has not be selected; the  
purple area represents the area that has been selected; the small purple square represents the present position of the cursor. To  
setup the area you want to be sensitive after you go into the setting interface; the purple small square will be flickering between  
two colors alternatively which are purple and green. Use the direction keys and enter button to switch the squares of the area you  
want to be sensitive to purple.  
3.3.5 PTZ Set  
PTZ Setup  
Channel Protocol Baud Rate ID  
1
2
3
4
Pelco-D  
Pelco-D  
Pelco-D  
Pelco-D  
9600  
9600  
9600  
9600  
01  
63  
63  
63  
Return  
By moving the cursor to PTZ Set and pressing [ENTER] key you can enter into quad channel Pan/Tilt/Zoom port setting interface  
1.Channel: Denotes systems channel number.  
2.Protocol: Denotes the communication protocol between the DVR and camera. By moving the cursor to this column and  
pressing the [ENTER] key you can choose the protocol you want to use from the following options:  
Pe1co-D/P/09-15/Dscp/FastDome/PIH1016-1017/JECFastD/RM110/Neocam,  
The protocol you select must match a protocol that is available on the camera or the DVR will not be able to communicate with  
the camera.  
3.Baud Rate: Denotes communication speed between the DVR and camera. By moving the cursor to this column and pressing the  
[ENTER] key you can choose the baud rate you want to use from the following options: (1200/2400/4800/9600), the baud rate  
you select must match the camera’s baud rate or the DVR will not be able to communicate with the camera.  
4.Camera ID: By moving the cursor to this column and pressing the [ENTER] button you can select the ID number you want to  
use to communicate with the camera. The options are: (01-63). You must set the same ID number on the DVR and the camera. All  
PTZ cameras attached to the DVR must have a different ID number. They can have the same protocol and baud rate, but they  
have to have different ID numbers so the DVR can determine which camera it is communicating with. The ID number can match  
the channel number, but it does not have to as long as the ID number in the DVR settings and the camera are the same.  
5.After completing all of the settings move the cursor to [RETURN] and press the [ENTER] key to return to the previous menu,  
and save the Pan/Tilt/Zoom camera settings.  
Attention: Pan/Tilt/Zoom protocol, baud rate, and ID number in the DVR must match the settings on the camera  
or the DVR will not be able to communicate with the camera.  
Pan/Tilt/Zoom operation: After setting Pan/Tilt/Zoom parameters correctly, press [F2] key on the remote control under  
single monitoring mode, the top left corner of screen will display “Pan/Tilt control” message temporarily, then you can operate  
the channels Pan/Tilt/Zoom camera by pressing the keys on the remote control and front panel.  
Pressing [F2] once more will exit Pan/Tilt/Zoom operation, and return to single image monitoring mode; Switch monitoring  
image and pressing [F2] key can enter into another channels Pan/Tilt/Zoom operation.  
Warning 1: When operating Pan/Tilt/Zoom function, system can not startup manual video recording function.  
Warning 2: When operating Pan/Tilt/Zoom function, once system starts up video recording (timing or alarm startup), you  
temporarily can not use Pan/Tilt operation.  
18  
 
QT19D328SC User’s Manual  
Troubleshooting: When Pan/Tilt/Zoom does not operate normally, Please check RS-485 connection and Pan/Tilt/Zoom setup.  
3.3.6 Network Set  
Move the cursor to Network Set and press Enter to get into the system’s network setup menu.  
See picture below:  
Network Setup  
IP Address:  
Subnet Mask:  
192.168.001.200  
255.255.255.000  
Default Gateway: 192.168.001.001  
Bandwidth:  
Video Port:  
Web Port:  
Setup  
08080  
08100  
Return  
a). IP address: Enter an IP address that will work with the settings on the router you attach the DVR to.  
b). Subnet Mask: Enter the Subnet Mask from the router the DVR is attached to.  
c). Default Gateway: Enter the Default Gateway from the router the DVR is attached to.  
d). Bandwidth: This feature can be used to set the speed of transfer of data over the network or internet. The options are 384kt,  
512kt, 1Mt, 2Mt. The lower the setting the lower the bandwidth needed to transfer the video but the video quality will be less, the  
higher the setting the more bandwidth needed but the quality of the video will be higher.  
e). Video Port: If you are connecting through an Internet Explorer browser set to 06101, if connecting through the client software  
program set to 08080  
f). Web Port: Set to 08100 for Internet Explorer or client program.  
NOTICE: Refer to the Internet Quick Start Guide for information on setting up the DVR for remote access.  
3.3.7 System Info  
Moving the cursor over [System Info] and pressing the [ENTER] key will enter into system information interface shown  
below:  
NOTICE: You can also get to this screen by pressing the CHECK button on the remote control while the DVR is in  
preview mode.  
19  
 
QT19D328SC User’s Manual  
Search Menu  
Playback All Record  
Log  
Record Status  
HDD Status  
Machine Info  
Exit  
a). Playback All Record: Use this option to search for recordings by record type (All, Timing, Alarm) and Date/Time.  
Date Time: Move cursor to this selection, and directly input the date and time, based on the recording date and time you want to  
playback;  
Now press [START] to see the available recording for that duration. If there is no record found, it will say “No Record”  
When selected date has video record, it will display the screen below:  
2009-06-17 All Record  
01 02 03 04 05 06 07 08 09 10 11  
12 13 14 15 16 17 18 19 20 21 22  
UP DN 23 24 25 26 27 28 29 30 31  
1 00000000 0800 - 0900 A 25  
1 00000000 0900 - 1000 R 25  
You can also scroll through other dates during the month to view the recording. If the date is in yellow color it means that there  
is a recording for that particular day. Press [ENTER] to view the available recording for that day.  
b). Log: Use this option to search the system log by type of event (All, Alarm, Motion Detection, Operation) and Date  
Moving cursor to [LOG] item, and pressing [ENTER] key will enter into inquiry log interface  
Input Date and Type of the Log  
Type: All Events  
Date: 2009-06  
Start  
 
Return  
QT19D328SC User’s Manual  
Type: includes all events recording mode, alarm mode, motion detection and operation mode; select the type of event you want,  
or select All Events and click start, the screen below will be displayed:  
Log Search: All Events  
06-17 12:20  
06-17 01:00  
06-17 02:15  
Motion Detect 1  
Parameter Set 5-01  
Video Loss 2  
Return PageUp  
PageDown  
c). Record Status: Current Recording Settings on the system.  
By moving cursor to [Record Status] option, and pressing [ENTER] key you will enter into record status interface, this  
screen will display video recording status, including video record mode, status, image quality, and frame rate.  
Channel Status  
Mode  
Quad  
Status  
Q Frame Alarm Motion  
30 Disar Off  
Return  
Record  
5
1) Mode: Displays current recording mode, Single mode, dual mode, quad image  
21  
 
QT19D328SC User’s Manual  
2Status: video status: Record/Idle  
3Image Quality: displays video record quality  
4Frame rate: displays video recording frame rate  
5Alarm: setting status alarm/disarm alarm two  
6Motion detection: turn on/ turn off.  
d). HDD Status: By moving cursor to [HDD Status] option, and pressing the [ENTER] key you will enter into the hard drive  
status information, this window will display current hard drive status, including total capacity and remaining space.  
HDD Status  
HDD  
1
Status  
Record  
Capacity  
249G  
Free_Space  
169,069MB  
2
3
4
None  
None  
None  
000G  
000G  
000,000MB  
000,000MB  
000,000MB  
000G  
Return  
e). Machine Info: By moving cursor to [Machine Info] option, and pressing the [ENTER] key you will enter into the machine  
information screen. This screen will display the current software version (firmware) and MAC address information (network).  
Version: 6214C-P-01.010  
MAC Address: 000.111.111.111.110  
Return  
You can change the MAC address by pressing [ENTER] key and entering numbers.  
Note: only super user can hold changing MAC address authority  
f). Exit: Moving cursor to this selection item, and pressing the [ENTER] key to confirm will exit to inquiry menu, and exit to  
monitoring screen.  
22  
 
QT19D328SC User’s Manual  
3.3.8 Basic Set  
By moving the cursor to [Basic Set] option and pressing the [ENTER] key will take you to the basic setup screen:  
Basic Setup  
Record Settings:  
Buzz Settings:  
Setup  
Off  
Language Settings:  
Fastigium Settings:  
English  
On  
Record Bag Settings: 30 minute  
USB Settings: Setup  
Video Spot Settings: 05 Second  
Return  
A). Record Settings: Selecting Setup and pressing the enter key display the screen below:  
Record Setup  
Quality:  
Frames: 30 (Global)  
Mode: VBR  
Return  
5
1) Quality: You can select from 1 to 8, The smaller the number the higher the image quality.  
2) Frames: The number of frames per second recorded from the cameras, the options are 8, 15, and 30. The more frames  
per second, the smoother the video, the lower the frames per second the more video files you can save on the hard drive.  
3) Mode: The bit rate format, there are 2 options, VBR (Variable Bit Rate), or CBR (Constant Bit Rate). With VBR the bit  
rate decreases when there is less motion and increases when there is more motion, so the quality of the image is less  
when there is less motion, and the quality is better when there is more motion. This can save hard drive space since  
smaller files are sent to the hard drive when there is no motion. With CBR the bit rate is always the same.  
4) Buzz Settings: The options are On or Off. If the setting is on the buzzer will sound if there is a hard drive error or  
password error.  
5) Language Settings: There are 2 choices, English and Chinese.  
6) Fastigium Settings: This setting prevents the monitor from going into sleep mode. By default the setting is On and  
the schedule is set for all day everyday. If you switch it to Off then the monitor can go into sleep mode and you will need  
to power the system off and back on to display the screen. To see the schedule, go to the On setting of the Fastigium line  
and press the enter button 3 times to display the following screen:  
Fastigium Time Setup  
Week  
First_Period Second_Period  
00:00-00:00  
Everyday 00:00-23:59  
******** 00:00-00:00 00:00-00:00  
******** 00:00-00:00 00:00-00:00  
******** 00:00-00:00 00:00-00:00  
******** 00:00-00:00 00:00-00:00  
******** 00:00-00:00 00:00-00:00  
******** 00:00-00:00 00:00-00:00  
******** 00:00-00:00 00:00-00:00  
Return  
B) Record Bag Settings: This option determines the length of the recorded files when you are recording manually. The  
options are 30, 45, and 60 minutes. As an example, if you select 30 minutes after recording for 30 minutes the system  
23  
 
QT19D328SC User’s Manual  
will start a new file.  
C) USB Settings: Select Setup and press the Enter button. You will have two options, Disable and Enable. Select Enable  
to active the USB port. After you select this option on press Enter the DVR will restart. After enabling the port you can  
connect the USB 2.0 port on the DVR to a USB 2.0 port on a PC you will be able to back up the files from the hard  
drive on the DVR to the hard drive on the PC.  
Playback: You will have an icon for the DVR in My Computer on the PC. The PC will find the new hardware and will  
put a new drive letter in "My Computer". Open the new drive letter by clicking on the icon to see the files. You can play  
the files back using the client program that comes with this DVR through the record info option and local playback.  
NOTICE: You will need to backup the entire hard drive from the DVR to the hard drive on the PC before you  
will be able to select individual files for playback.  
G) Video Spot Settings: When you attach a monitor to the second video out port it will display each of the cameras in  
sequence. You can use this option to select the length of time that each camera appears before switching to the next camera.  
The options are 5, 10, and 15 seconds.  
3.4 Screen Settings  
When the system is in the single screen mode you can adjust the picture quality  
Brightness: press the analog key on the remote control, the screen will show “Brightness” on the top right hand corner.  
Press “–” or “+” to adjust the brightness as desired.  
Saturation: Press the “Analog” key for second time and “Saturation” appears on the top right hand corner. Press “–” or “+”  
to adjust the saturation as desired.  
Contrast: Press the “Analog” key for third time and “Contrast” appears on the top right hand corner. Press “–” or “+” to  
adjust the contrast as desired.  
Hue: Press the “Analog” key for the fourth time and “Hue” appears on the top right hand corner. Press “–” or “+” to adjust  
the color as desired.  
Appendix A System Specifications  
Monitor  
17'' 4:3 TFT/LCD  
Video Input  
Four Channels Independent Input 1.0Vp-p, 75Ω BNC  
Video  
Two Channels PAL/NTSC output1.0Vp-p, 75Ω BNC, Multiple Video Signal  
Video Output  
One Channel VGA display output  
24  
 
QT19D328SC User’s Manual  
Video Display  
Single picture, built-in quad display  
PAL system: 25 frames/second CCIR625 lines 50 fields  
NTSC system: 30 frames/second CCIR625 lines 50 fields  
Video Standard  
Real time recording resources, one or four channels can play backward at the same  
System Resources  
timeone or four channel monitoring, network real time monitoring  
Audio Input  
Two channels independent input 600Ω RCA  
Audio Output  
Two channels independent output  
1.0-2.2V  
600Ω RCA  
Basic Output Gain  
Distortion Plus Noise  
Recording Solutions  
Audio Compression  
Operating Language  
Operating Interface  
Password control  
Image Compression  
Audio  
-30dB  
Volume and Image are Synchronized  
MPEG-1 LAYER2  
English  
System  
OSD (On Screen Display) menu  
Password for users and administrators  
MPEG-4 Variable bit streams/ Constant bit streams  
Built-in quad CIF format352×288 Single picture HD1 format 704×576  
Image format  
pixels )  
pixels)  
Video code rate  
6.25-350Kbyte/s  
22.5M-1260Mbyte/hour  
6.25-250Kbyte/s  
22.5M-900Mbyte/hour  
Video volume taken in H.D.  
Play backward 352×288 Pixelsreal time monitoring 704×576 pixelsVGA output  
Resolution  
704×576 pixels  
Digital  
Processing  
and Storage  
Video current standard  
Audio current standard  
Audio code rate  
ISO14496  
ISO11172  
24Kbyte/s  
Audio volume taken in H.D.  
Internal Storage  
86.4Mbyte/hour  
One IDE hard driveup to 300GB  
8 adjustable levels1-8 with 1 highest quality  
Full duplex  
Image quality  
Data read and write method  
Motion Detection  
Alarms  
192 detecting areas can be set, and 16 levels adjustable sensitivity  
25  
 
QT19D328SC User’s Manual  
Four channels alarm inOn/off valueinput independently  
Open/ close circuit  
Alarm input  
Alarm Input options  
One channel linkage alarm outputone channel power trouble alarm outputone  
channel other trouble alarm output  
Alarm Output  
Relay on/off value1A 120VAC/24VDClongtime on/off optional  
PTZ Port  
RS485  
Other Ports  
Serial Port  
RS232 universal serial interface  
RJ-45 10M/100M Ethernet interface  
Support TCP/IP  
Network Port  
Network Transport protocols  
Network Transport  
Browsing Solutions  
Clock  
Network  
interface  
ADSL, ISDN, LAN, CAN  
Software included, Internet Explorer  
Built-in hard clock and permanent calendar  
AC90 250  
Power  
Power Consumption  
Video System  
Max Brightness  
Max Contrast  
Response Time Tr/Tf  
Visual Angle  
Max55W  
Universal video system  
300cd/m2  
Others  
450:1  
Tr+Tf=16ms)  
170°/150°  
Weight  
13 lbs (6.0Kg)Not Including H.D.)  
Dimensions  
15.25 in x16 in x 121 in (387mm×406mm×121mm)  
( W×H×D)  
Appendix B Camera Specifications  
Model  
Image Sensor  
Lens  
QD28414 & QD28414W  
1/4" Sony Super HAD Color CCD  
4-QD28414 with 6mm and 4-QD28414W with 3.6mm  
420TVL  
Horizontal Resolution  
26  
 
QT19D328SC User’s Manual  
Effective Pixels  
Field of View  
510x492 NTSC  
42° for 6mm, 74° for 3.6mm  
BNC (F), 12VDC 2.1mm (F)  
0 Lux  
Connectors  
Minimum Luminance  
Infrared LEDs/Distance 12/30ft  
IR LED Wavelength  
Video Output  
850nm  
1 Vp-p75 ohm  
Electronic Shutter Speed 1/50 (1/60)-1/100,000sec  
Audio Output  
None  
S/N Ratio  
>48dB  
Gamma Characteristic  
Power Supply  
0.45  
12V DC  
Power Consumption  
Operating Temperature  
Dimensions  
120mA (300mA Max with LEDs on) per camera  
-4°F to 122°F  
2.5(W) x 3.5 (D) x 2.5 (H) in  
12 oz (340 g)  
Weight  
Appendix C Product Service & Warranty  
Thank you for choosing our products.  
All of our products have a conditional free warranty repair service for hardware within 12 months starting  
from purchase date, and a free exchange service within one month (valid for manufacturing defects). Permanent  
upgrading service is provided for the software.  
Liability Exclusions:  
Any product malfunction, abnormalities in operation or damage caused by following reasons are not within  
the free service scope of our company. Please select payable service.  
27  
 
QT19D328SC User’s Manual  
(1) Equipment damage caused by improper operation  
(2) Improper environment and conditions in/on which the equipment operates, e.g., improper power, environment  
temperature, humidity and lightening strike etc. that cause equipment damage.  
(3) Damage caused by acts of nature: earthquake and fire etc.  
(4) Equipment damage caused by the maintenance of personnel not authorized by our company.  
(5) Product sold over 12 months ago.  
In order to provide various services to, please complete registration procedure after you purchase the  
product. Cut off or copy Your Information Card and fax or mail it to us after the card is filled in. You can also  
register the product by going to the www.q-see.com website and clicking on the Register link.  
If you have questions:  
Contact Us:  
Mailing Address:  
DPS Inc.  
8015 E. Crystal Dr  
Anaheim, CA 92807  
Customer Service:  
Phone: 877-998-3440 x 538  
Live Chat from www.q-see.com  
Website:  
Tech Support:  
Fax: 714-998-3509  
Phone: 877-998-3440 x 539  
Live Chat from www.q-see.com  
28  
 
Customer Information Card  
You’s Name  
Company Name  
Postal Address  
Postal code  
Phone Number  
E-mail  
Mr./Mrs.  
Model Number  
of Product  
Serial Number of  
Product  
Purchase Date  
Distributor  
The material in this document is the intellectual property of our company.  
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by  
any means without our company’s prior written permission.  
1. Our products are under continual improvement and we reserve the right to make changes without notice.  
But no guarantee is given as to the correctness of its contents.  
2. We do not accept any responsibility for any harm caused by using our product.  
3. The product picture may differ from the actual product, which is only for r reference. The accessories will  
probably be different according to the different selling areas. For details of accessories, please refer to r local  
distributor.  
Copyright reserved  
 

Radica Games Handheld Game System I7008 User Guide
Radio Shack MP3 Player 42 541 User Guide
Radio Shack Telephone ET 501 User Guide
Recoton Advent Scale EC Series User Guide
Remington Trimmer BS1812A User Guide
Ricoh Printer BP20 User Guide
Runco Flat Panel Television CX 42HD User Guide
SanDisk Computer Drive 20 10 00038 User Guide
Sanyo Flat Panel Television AVP 429 User Guide
Schumacher Battery Charger SCF 10000A User Guide